• 한국세라믹학회지
• /
• 제46권5호
• /
• pp.452-455
• /
• 2009

A cost-effective route to synthesize $\beta$-SiAlONs from Si mixtures by reaction bonding followed by post-sintering was investigated. Three different z values, 0.45, 0.92 and 1.87, in $Si_{6-z}Al_zO_zN_{8-z}$ without excess liquid phase were selected to elucidate the mechanism of SiAlON formation and densification. For RBSN (reaction-bonded silicon nitride) specimens prior to post-sintering, nitridation rates of more than 90% were achieved by multistep heating to $1400^{\circ}C$ in flowing 5%$H_2$/95%$N_2$; residual Si was not detected by XRD analysis. An increase in density was acquired with increasing z values in post-sintered specimens, and this tendency was explained by the presence of higher amounts of transient liquid phase at larger z values. Measured z values from the synthesized $\beta$-SiAlONs were similar to the values calculated for the starting compositions. Slight deviations in z values between measurements and calculations were rationalized by a reasonable application of the characteristics of the nitriding and post-sintering processes.

• Fibers and Polymers
• /
• 제4권4호
• /
• pp.199-203
• /
• 2003

In order to investigate the effects of cross-sectional shapes on the sound characteristics of polyester fibers, 10 specimens were woven into a twill structure made of round, hollow, triangular, u-shape, cruciform, and composite cross-sectional (▲/▲ ,()/▲, Y/Y) fibers. Their rustling sounds were recorded, and their sound spectra were obtained from FFT analysis. Physical sound parameters (LPT, ΔL, Δf) and Zwicker's psychoacoustic parameters of the loudness(Z), sharpness(Z), roughness(Z), and fluctuation strength(Z) were calculated from the sound spectra. According to noncircular cross-section fibers, the hollow shaped fiber had the highest value of LPT, ΔL, loudness(Z), and fluctuation strength(Z). The triangular shaped fiber had a lower value of LPT, ΔL, loudness(Z), and roughness(Z) than those of the round shaped fiber. Among composite cross-section fibers, C1(▲/▲) and C3 (Y/Y) had higher values of LPT, ΔL, Δf and loudness(Z) but C2(()/▲) had lower values. Also the LPT, ΔL, sharpness(Z), and roughness(Z) values of different denier were similar to each other, but the Δf and loudness(Z) values increased as the denier increased.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제51권8호
• /
• pp.368-373
• /
• 2002

The inverse z-transform of a z-domain expression of a sequence can be Performed in many different methods among which the recursive computational method is based on the difference equation. In applying this method, a few initial values of the sequence should be obtained separately. Although the existing method generates the right initial values of the sequence, its derivation and justification are not theoretically in view of the definition of z-transform and its shift theorems. In this paper a general approach for formulating a difference equation and for obtaining required initial values of a sequence is proposed, which completely complies to the definition of the z-transform and an interpretation of the validity of the existing method which is theoretically incorrect.

• The Journal of Advanced Prosthodontics
• /
• 제3권3호
• /
• pp.126-131
• /
• 2011

PURPOSE. The aim of this in vitro study was to examine the curing efficiency of various resin-based materials polymerized through ceramic restorations with 3 different thicknesses. Curing efficiency was evaluated by determining the surface microhardness (VHN) of the resin specimens. MATERIALS AND METHODS. Four kinds of resin materials were used. Z350 (3M ESPE $Filtek^{TM}$ Z350: A2 Shade), Z250 (3M ESPE $Filtek^{TM}$ Z250: A2 Shade) and $Variolink^{(R)}$ II (VL: Ivoclar vivadent, base: transparent) either with or without a self-curing catalyst (VLC: Ivoclar vivadent, catalyst: low viscosity/transparent) were filled into the silicone mold (10 mm diameter, 1 mm thick). They were cured through ceramic discs (IPS e.max Press MO-0 ingot ivoclar vivadent, 10 mm diameter, 0.5, 1 and 2 mm thicknesses) by LED light-curing units for 20 and 40 seconds. Vicker's microhardness numbers (VHNs) were measured on the bottom surfaces by a microhardness tester. Data were analyzed using a 3-way analysis of variance (ANOVA) at a significance level of 0.05. RESULTS. The thickness of ceramic disc increased, the VHNs of all four resin types were decreased (P<.05). The mean VHN values of the resins light cured for 40 seconds were significantly higher than that of LED for 20 seconds in all four resin materials (P<.05). VLC showed significantly higher VHN values than VL regardless of other conditions (P<.05). Z350 and Z250 showed higher values than VL or VLC (P<.01). CONCLUSION. Thinner ceramic disc with increased curing time resulted higher VHN values of all resin materials. The use of a catalyst produced a greater hardness with all polymerization methods. Restorative resin materials (Z350, Z250) showed higher VHN values than resin cement materials (VL, VLC).

• 대한전자공학회논문지
• /
• 제22권3호
• /
• pp.23-30
• /
• 1985

디지탈 필터의 구성이 차분방정식에 근거하였을 때, 그 주파수 특성을 구하는 방법은 계산에 의해 할 수 있는 식이 없으므로 Z-변환식으로 미루어 짐작하거나 실험에 의해 측정하는 방법 밖에 없다. 본 논문에서는 차분방정식으로 표현된 함수의 주파수 응답 진폭특성을 계산하는 방법을 Parseval의 정리를 도입하여 제시하고, 이 식의 타당성을 확인하기 위해 실제로 두 종류의 디지탈 필터를 설계 제작하고 실험 측정하였다. 측정된 결과와 Z-변환식에 의한 계산값, 본 논문에서 제시한 계산식에 의한 값을 서로 비교하였다. 그 결과 차분방정식에 의해 계산된 값이 훨씬 실제 측정값에 접근하였다. 또한 Z-변환식에 의한 결과보다 예리한 roll-off 특성을 보여 줌을 확인했다. 따라서 차분방정식을 기초로 하여 구성된 디지탈 필터의 진폭응답 특성은 Z-변환식보다 차분방정식에 의한 계산이 보다 나은 실제적인 결과를 예측해 준다.

• Advances in materials Research
• /
• 제5권2호
• /
• pp.93-105
• /
• 2016

KNN-based ceramics modified with small amounts of $Bi_4Zr_3O_{12}$ (BiZ) has been synthesized using high-throughput experimentation (HTE). The results from X-ray diffraction show that for samples with base composition $(K_{0.5}Na_{0.5})NbO_3$ (KNN), the phase present changes from orthorhombic to pseudo-cubic with more than 0.2 mol% BiZ addition; for samples with base composition $(K_{0.48}Na_{0.48}Li_{0.04})(Nb_{0.9}Ta_{0.1})O_3$ (KNNLT), the phase present changes from a mixture of orthorhombic and tetragonal symmetry to pseudo-cubic with more than 0.4 mol % while for samples with base composition $(K_{0.48}Na_{0.48}Li_{0.04})(Nb_{0.86}Ta_{0.1}Sb_{0.04})O_3$ (KNNLST), the phase present is tetragonal with <0.3 mol% BiZ addition and transforms to pseudo-cubic with more dopant addition. The microstructures of the samples show that addition of BiZ decreases the average grain size and increases the volume of pores at the grain boundaries. The values of dielectric constant for KNN and KNNLT compositions increase slightly with BiZ addition while that for KNNLST decreases gradually with BiZ addition. The dielectric loss values are between 0.02 and 0.04 for KNNLT and KNNLST compositions while they are ~ 0.05 for KNN samples. The resistivity values increases with BiZ addition and values in the range of $10^{10}{\Omega}cm$ and $10^{12}{\Omega}cm$ are obtained. The piezoelectric charge coefficient ($d{^*}_{33}$) is highest for KNNLST samples and decreases gradually from ~400 pm/V to ~100 pm/V with BiZ addition.

• 대한수학회보
• /
• 제54권2호
• /
• pp.593-605
• /
• 2017

In this paper, we consider some normality criteria concerning multiple values. Let $\mathcal{F}$ be a family of meromorphic functions defined in a domain D. Let k be a positive integer and ${\psi}(z){\not\equiv}0$, ${\infty}$ be a meromorphic function in D. If, for each $f{\in}\mathcal{F}$ and $z{\in}D$, (1) $f(z){\neq}0$, and all of whose poles are multiple; (2) all zeros of $f^{(k)}(z)-{\psi}(z)$ have multiplicities at least k + 3 in D; (3) all poles of ${\psi}(z)$ have multiplicities at most k in D, then $\mathcal{F}$ is normal in D.

• 대한수학회보
• /
• 제56권3호
• /
• pp.789-799
• /
• 2019

In this paper, we deal with unicity of a nonconstant zero-order meromorphic function f(z) and its shift f(qz) when they share four distinct values IM or share three distinct values with multiplicities truncated to level 4 in the extended complex plane, where $q{\in}\mathbb{C}{\setminus}\{0\}$. We also give an uniqueness result for f(z) sharing sets with its shift.

• Restorative Dentistry and Endodontics
• /
• 제23권1호
• /
• pp.424-432
• /
• 1998

To get a satisfactory result in the composite resin restorations, it is necessary to choose correct shade. At present, most of the commercial composite resins are based on the Vita Lumin shade guide or Bioform shade guide, but color differences might be expected even using the same shade in various materials. In this study, five kinds of light-cured composite resins with A2 and B3 shade were used to measure and compare the color each other while one porcelain served as a control. All composite resins (Spectrum TPH (SP), VeridonFil- Photo (VE), Z100 (Z100), Charisma (CH), Prodigy (PRO)) were filled in to the metal mold (12 mm diameter, 2 mm depth), followed by compression, polymerization and polishing with wet sandpaper. The specimens of porcelain were fabricated by using the refractory mold for porcelain. After 24 hours, the specimens were placed on the spectrocolorimeter and spectral reflectance were measured under CIE illuminant D65. After measuring the values of $L^*$, $a^*$, $b^*$ and ${\Delta}E^*$, following results were obtained; 1. The $L^*$, $a^*$ and $b^*$ values of both shade of porcelain specimens showed significantly higher than those of resin specimens(p<0.05). 2. In comparing the resin specimens of the A2 shade, differences were significant except $L^*$ values of SP-CH and PRO-VE, $a^*$ values of the VE-SP and $b^*$ values of the VE-Z100 and SP-PRO(p<0.05), 3. In comparing the resin specimens of the B3 shade, differences were significant except $L^*$ values of PRO-SP, $a^*$ values of the SP-PRO and Z100-VE and b* values of the PRO-SP(p<0.05). 4. In comparing the resin specimens of the A2 shade, color differences between materials (${\Delta}E^*$) showed the lowest value of 1.66, and the highest was 5.16. ${\Delta}E^*$ values of the materials of VE-PRO, CH-PRO, SP-PRO, SP-Z100 and SP-CH were lower than 3.3. 5. In comparing the resin specimens of the B3 shade, the lowest value of the ${\Delta}E^*$ was 0.57 and the highest was 5.92. ${\Delta}E^*$ values of Z100-CH and SP-PRO were lower than 3.3. The present study revealed there was perceptible color difference between materials even if they have the same designated shade based on Vita shade guide. The results of the present study suggested that it would be necessary to establish the reproducible and constant color specification system for an esthetic restoration.

• 한국수산과학회지
• /
• 제12권4호
• /
• pp.209-215
• /
• 1979

부산수산대학실습선 '새바다'(GT: 2,275.7ton)에 관한 조종성능을 구명하기 위하여, 실선에 의한 Z 조종시험을 한 결과를 요약하면 다음과 같다. 1. '새바다'호의 $10^{\circ}Z$시험에서의 선회성지수 K'값은 1.052, 추종성지수 T' 값은 0.815, $20^{\circ}Z$ 시험에서의 K'값은 0.925, T'값은 0.502, $30^{\circ}Z$ 시험에서의 K' 값은 0.877, T' 값은 0.441로서, 소타각사용시의 조종성능과 대타각사용시의 조종성을 비교하여 보면, 대타각을 사용할 때 보다 추종성을 좋아지나 선회성을 낮아진다는 것을 알 수 있다. 2. '새바다'호의 $10^{\circ}Z$ 시험에서의 선회성지수 K' 값과 추종성지수 T' 값은 어선의 표준식에 가까움으로 어선으로서 양호한 조종성능을 가지고 있다고 볼 수 있었다. 다만 길이와 크기에 비하여 K'값이 약간 적은 수치이며, $10^{\circ}Z,\; 20^{\circ}Z,\;20^{\circ}Z$ 시험에서의 회두각곡선의 overshoot angle이 약간 크므로 추종성은 좋으나 선회성은 낮은 편임을 알 수 있었다. 3. '새바다'호의 조종성능은 추종성에 비하여 선회성이 낮으므로 선회경도 크게 되며, 또한 대각도전타시에 비하여 선회성이 낮아지므로, 충돌이나 좌초를 회피하기 위하여 대각도전타를 할 경우에는 안전한게 접근거리를 크게 두어 한기전타하는 등 조선상주의를 요한다. 4. '새바다'호의 $10^{\circ}$시험에서의 1조작간항주거리하는 배 길이의 약 8.6배로서 일반선박의 조종성표준거리 $5\~11$배의 이내가 되므로 '새바다'호의 조종성능은 총합적으로 양호하다는 것을 알 수 있었다.