• Journal of The Korean Society of Grassland and Forage Science
• /
• v.35 no.2
• /
• pp.81-86
• /
• 2015

"Youhan" (Hordeum vulgare L.), a new whole-crop barley cultivar, was developed by the breeding team at National Institute of Crop Science, RDA in 2012. Youhan has the growth habit of III, a light green and mid-sized leaf, hooded and lax-type spikes. The cultivar showed 107 cm of culm length, 641 spikes per $m^2$. The heading date of Youhan was May 1, which is one day later than that of the check cultivar "Yuyeon" in upland, and 2 days earlier than that of Yuyeon in paddy field. The maturation time was similar to check cultivar Yuyeon on June 4 in upland and May 31 in paddy field. In terms of winter hardiness and resistance to lodging and disease, Youhan also performed better than the check cultivar. The average forage dry matter (DM) yield in the regional yield trial was approximately 12.6 ton $ha^{-1}$ and 12.0 ton $ha^{-1}$ in upland and paddy field, respectively, which were 6% and 5% higher than that of the check. The yield also showed 7.3% of crude protein, 26.8% of ADF (acid detergent fiber), 47.8% of NDF (neutral detergent fiber), 67.7% of TDN (total digestible nutrients), and a higher grade of silage quality for the whole-crop barley. Fall sowing cropping of Youhan is recommended only in those areas where the average daily minimum-mean temperatures in January are higher than $-8^{\circ}C$, and it should not be cultivated in mountainous areas of Korea.

• Proceedings of the SAREK Conference
• /
• 2007.06a
• /
• pp.124-124
• /
• 2007

• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.866-869
• /
• 2004

무선을 이용한 위치 추적방법은 최근에 많은 관심을 받고 있다. 이 방법들은 적용지역환경 및 대상에 따라 적절한 방법을 선정하여 사용하는 것이 중요할 뿐만 아니라 신뢰성을 갖는 것 또한 매우 중요하다. 본 논문에서는 일정한 노선으로 움직이는 열차라는 이동체를 대상으로 하여 적용 가능한 알고리즘에 대하여 검토하였으며, 이는 1차원에서 물체의 위치를 추적하는 방법으로써, 열차와 같은 일정한 노선 위를 이동하는 물체의 위상을 추적하여 이동체의 위치를 결정하는 알고리즘을 구현을 위한 방법과 조건을 제시하였으며 철도시스템으로 확장 적용을 위한 알고리즘을 제시하였다.

• Proceedings of the KIEE Conference
• /
• 2001.04a
• /
• pp.317-319
• /
• 2001

A Switched Reluctance Generator attracts much attention in the generator because of high efficiency, simplicity, and ruggedness. However, they require rotor position information to operate. In many systems, the rotor position sensor is expensive, limited and undesirable. This paper describes a new approach to estimating the rotor position of a SRG from the measured terminal voltage and current for rotor position sensorless control. The proposed method Is based on the instantaneous inductance of the SRG. The proposed technique is very simple and it is able to apply to high speed operation under the stable condition because of its simplicity. The initial rotor position estimation algorithm is efficient and reliable. The proposed method is verified by computer simulation.

• Journal of the Korean Society of Safety
• /
• v.20 no.3 s.71
• /
• pp.14-18
• /
• 2005

The ultrasonic handy scanner to be developed in this research is a nondestructive inspection equipment with various facility. The ultrasonic inspection is the technique area which apply range is increasing greatly with IT. The purpose of this research is development of a ultrasonic handy scan inspection device with the utility in a work spot. The ultrasonic handy scanner to be developed with portability in this research is able to carry out the spot inspection. It can contribute to the quality improvement, cost reduction and safety design.

• Proceedings of the SAREK Conference
• /
• 2006.06a
• /
• pp.566-571
• /
• 2006

The purpose of this code is to relate the various controllable factors to the comfort and well-being of the people using the building, so that the requirements of the system may be specified to the designers and the constructor. This study deals with the work involved in design and installation of residential mechanical ventilation. The recommendations made in this code recognize the need to optimize the use of energy, reduce hazards and minimize effects detrimental to the environment. This code was prepared by a committee convened by SAREK. The code provides broad guidance only on certain topics. The titles of standard and code referred to in this code are listed on the reference.

• Korean Journal of Materials Research
• /
• v.28 no.10
• /
• pp.601-609
• /
• 2018

To study the effects of graphite shape and the composite fabricating method on the mechanical properties of graphite/copper (Gr/Cu) composites, a copper composite using graphite flakes or graphite granules as reinforcing phases is fabricated using mechanical mixing or electroless plating method. The mechanical properties of the Gr/Cu composites are evaluated by compression tests, and the compressive strength and elongation of the Gr/Cu composites using graphite granules as a reinforcing phase are compared with those of Cu composites with graphite flakes as a reinforcing phase. The compressive yield strength or maximum strength of the Gr/Cu composites with graphite granules as a reinforcing phase is higher than that of the composites using graphite flakes as a reinforcing phase regardless of the alignment of graphite. The strength of the composite produced by the electroless plating method is higher than that of the composite material produced by the conventional mechanical mixing method regardless of the shape of the graphite. Using graphite granules as a reinforcing phase instead of graphite flakes improves the strength and elongation of the Gr/Cu composites in all directions, and reduces the difference in strength or elongation according to the direction.

• Journal of the Korean institute of surface engineering
• /
• v.50 no.4
• /
• pp.244-250
• /
• 2017

Effects of plating conditions (dispersant concentration, plating time, and ultrasonication) on electroless Cu plating on SiC fabric woven by crossing of SiC continuous fibers vertically were studied. The ultrasonic dispersion treatment not only did not improve the dispersion of the SiC fibers, but also did not change the plating thickness. The ultrasonication in the pretreatment step of electroless plating did not improve the dispersion of the fibers, while the ultrasonication in the plating step enhanced the dispersion of the fibers and decreased the thickness of the Cu films. It was possible to control the thickness of the Cu coating layer as well as the dispersion of the fibers in the fabric by changing the plating conditions such as dispersant concentration, plating time, and ultrasonication, but it was very difficult to coat copper on the intersection of vertical fibers in the fabric.

• Korean Journal of Materials Research
• /
• v.28 no.12
• /
• pp.725-731
• /
• 2018

We investigate the reduction of $SnO_2$ and the generation of syngas($H_2$, CO) using methane($CH_4$) and hydrogen($H_2$) or a mixed gas of methane and hydrogen as a reducing gas. When methane is used as a reducing gas, carbon is formed by the decomposition of methane on the reduced Sn surface, and the amount of generated carbon increases as the amount and time of the supply of methane increases. However, when hydrogen is used as a reducing gas, carbon is not generated. High purity Sn of 99.8 % and a high recovery rate of Sn of 93 % are obtained under all conditions. The effects of reducing gas species and the gas mixing ratio on the purity and recovery of Sn are not significantly different, but hydrogen is somewhat more effective in increasing the purity and recovery rate of Sn than methane. When 1 mole of methane and 1 mole of hydrogen are mixed, a product gas with an $H_2/CO$ value of 2, which is known to be most useful as syngas, is obtained.