• 대한기계학회논문집
• /
• 제17권5호
• /
• pp.1115-1122
• /
• 1993

Several yield criteria for porous materials are compared with each other, defining the apparent yield stress as the yield stress of the porous material in simple compression. It was found that the plastic Poisson's ratio is the parameter needed to define the yield criterion, rather than the relative density. The plastic Poisson's ratio is regarded as a material characteristic that is obtained from a simple compression test. A new form of yield criterion was suggested, and it was applied to hydrostatic compression as well as uniaxial strain compression of sintered Al-2024 powder. The crossover point in the mean stress vs volume change curves of the processes was predicted. It is presented that the flow stress of the fully densed material can be obtained from that of the porous material using relations obtained from the yield criterion.

• Earthquakes and Structures
• /
• 제12권4호
• /
• pp.397-407
• /
• 2017

To estimate the structural seismic demand, some methods are based on an equivalent linear system such as the Capacity Spectrum Method, the N2 method and the Equivalent Linearization method. Another category, widely investigated, is based on displacement correction such as the Displacement Coefficient Method and the Coefficient Method. Its basic concept consists in converting the elastic linear displacement of an equivalent Single Degree of Freedom system (SDOF) into a corresponding inelastic displacement. It relies on adequate modifying or reduction coefficient such as the inelastic deformation ratio which is usually developed for systems with known ductility factors ($C_{\mu}$) and ($C_R$) for known yield-strength reduction factor. The present paper proposes a rational approach which estimates this inelastic deformation ratio for SDOF bilinear systems by rigorous nonlinear analysis. It proposes a new inelastic deformation ratio which unifies and combines both $C_{\mu}$ and $C_R$ effects. It is defined by the ratio between the inelastic and elastic maximum lateral displacement demands. Three options are investigated in order to express the inelastic response spectra in terms of: ductility demand, yield strength reduction factor, and inelastic deformation ratio which depends on the period, the post-to-preyield stiffness ratio, the yield strength and the peak ground acceleration. This new inelastic deformation ratio ($C_{\eta}$) is describes the response spectra and is related to the capacity curve (pushover curve): normalized yield strength coefficient (${\eta}$), post-to-preyield stiffness ratio (${\alpha}$), natural period (T), peak ductility factor (${\mu}$), and the yield strength reduction factor ($R_y$). For illustrative purposes, instantaneous ductility demand and yield strength reduction factor for a SDOF system subject to various recorded motions (El-Centro 1940 (N/S), Boumerdes: Algeria 2003). The method accuracy is investigated and compared to classical formulations, for various hysteretic models and values of the normalized yield strength coefficient (${\eta}$), post-to-preyield stiffness ratio (${\alpha}$), and natural period (T). Though the ductility demand and yield strength reduction factor differ greatly for some given T and ${\eta}$ ranges, they remain take close when ${\eta}>1$, whereas they are equal to 1 for periods $T{\geq}1s$.

• 한국물환경학회지
• /
• 제23권5호
• /
• pp.650-658
• /
• 2007

The Universal Soil Loss Equation (USLE) has been used in over 100 countries to estimate potential long-term soil erosion from the field. However, the USLE estimated soil erosion cannot be used to estimate the sediment delivered to the stream networks. For an effective erosion control, it is necessary to compute sediment delivery ratio (SDR) for watershed and sediment yield at watershed outlet. Thus, the Sediment Assessment Tool for Effective Erosion Control (SATEEC) was developed to compute the sediment yield at any point in watershed. In this study, the SATEEC was applied to the Sudong watershed, Chuncheon Gangwon to compare the sediment yield using area-based sediment delivery ratio (SDRA) and slope-based sediment delivery ratio (SDRS) at watershed outlet. The sediment yield using the SDRA by Vanoni, SYA and the sediment yield using the SDRS by Willams and Berndt, SYS were compared for the same sized watersheds. The 19 subwatersheds was 2.19 ha in size, the soil loss and sediment yield were estimated for each subwatershed. Average slope of main stream was about 0.86~3.17%. Soil loss and sediment yield using SDRA and SDRS were distinguished depending on topography, especially in steep and flat areas. The SDRA for all subwatersheds was 0.762, however the SDRS were estimated in the range of 0.553~0.999. The difference between SYA and SYS was -79.74~27.45%. Thus site specific slope-based SDR is more effective in sediment yield estimation than area-based SDR. However it is recommended that watershed characteristic need to be considered in estimating yield behaviors.

• Earthquakes and Structures
• /
• 제13권1호
• /
• pp.59-66
• /
• 2017

Modern seismic codes rely on performance-based seismic design methodology which requires that the structures withstand inelastic deformation. Many studies have focused on the inelastic deformation ratio evaluation (ratio between the inelastic and elastic maximum lateral displacement demands) for various inelastic spectra. This paper investigates the inelastic response spectra through the ductility demand ${\mu}$, the yield strength reduction factor $R_y$, and the inelastic deformation ratio. They depend on the vibration period T, the post-to-preyield stiffness ratio ${\alpha}$, the peak ground acceleration (PGA), and the normalized yield strength coefficient ${\eta}$ (ratio of yield strength coefficient divided by the PGA). A new inelastic deformation ratio $C_{\eta}$ is defined; it is related to the capacity curve (pushover curve) through the coefficient (${\eta}$) and the ratio (${\alpha}$) that are used as control parameters. A set of 140 real ground motions is selected. The structures are bilinear inelastic single degree of freedom systems (SDOF). The sensitivity of the resulting inelastic deformation ratio mean values is discussed for different levels of normalized yield strength coefficient. The influence of vibration period T, post-to-preyield stiffness ratio ${\alpha}$, normalized yield strength coefficient ${\eta}$, earthquake magnitude, ruptures distance (i.e., to fault rupture) and site conditions is also investigated. A regression analysis leads to simplified expressions of this inelastic deformation ratio. These simplified equations estimate the inelastic deformation ratio for structures, which is a key parameter for design or evaluation. The results show that, for a given level of normalized yield strength coefficient, these inelastic displacement ratios become non sensitive to none of the rupture distance, the earthquake magnitude or the site class. Furthermore, they show that the post-to-preyield stiffness has a negligible effect on the inelastic deformation ratio if the normalized yield strength coefficient is greater than unity.

• 한국작물학회지
• /
• 제31권3호
• /
• pp.299-303
• /
• 1986

녹두재배시 토양중 검기비 조절효과에 대한 기초자료를 얻기 위하여 pH가 낮은 개간지 토양과 pH가 높은 숙전의 토양에 질소, 인산, 가리를 조합 시비한 시험에서 식물체와 토양시료를 심취 분석하여 이들의 검기비와 녹두수량과의 관계를 검토한 결과는 다음과 같다. 1. 개화기 토양중 Ca/Mg비는 녹두의 검수, 분지수 및 수량과 정의 관계가 있었으며 (equation omitted) 비는 검수 및 수량과 정의 상관관계가 있었다. 2. 개화기 토양중 Ca/Mg의 절위는 1.9∼6.4 절위이었으며 3.9 이상에서는 녹두 수량에 크게 영향하지 않았으나 1.9∼3.9 사이에서는 3.9에 가까울수록 녹두수량은 급격히 증가되었다. 3. 개화기 토양중 (equation omitted) 비는 0.17∼0.33절위이었으며 0.23이상에서는 수량차이가 없었으나 그 이하에서는 수량감소가 심했다. 4. 수확기 식물체중 Ca/Mg의 절위는 1.4∼4.3이었으며 2.6 이상에서는 수량차이가 없었으나 1.4∼2.6 사이에서는 Ca/Mg 비가 클수록 수량이 증가되었다.

• Journal of Biosystems Engineering
• /
• 제37권1호
• /
• pp.58-64
• /
• 2012

Purpose: The objective of this study was to investigate the feasibility of anaerobic digestion of Chinese cabbage waste juice (CCWJ) and swine manure(SM). Methods: The anaerobic digestion test was conducted under batch and continuous conditions at mesophilic temperature ($36-38^{\circ}C$). The batch test was divided into Experiment I and II. In the Experiment I, biogas potential and production rate of CCWJ was evaluated. In Experiment II the effect of F/M ratio (2.0, 3.2, 4.9) at mixture ratio of 25:75(CCWJ: SM, % vol. basis) on biogas yield was studied. Results: CCWJ produced biogas and methane yield of 929 and 700 mL/g VS added respectively. The biogas yield from the mixture of CCWJ and SM was almost same at F/M ratio of 2.0 and 3.2 but dropped by 14% when F/M ratio increased from 3.2 to 4.9. In continuous test the mixture of CCWJ and SM (25:75, % vol. basis) produced biogas yield of 352 mL/g VS added which is around 11% higher compared to biogas yield from SM alone. Addition to biogas yield digester performance was also improved with co-digestion of CCWJ with SM. Conclusions: The results showed that the anaerobic digestion of CCWJ with SM could be promising for improving both the biogas yield and digester performance at mesophilic temperature.

• 한국환경과학회지
• /
• 제7권4호
• /
• pp.451-460
• /
• 1998

The objectives of this study Is to evaluate the total runoff yield, peak flow and peak flow travel time depending on the urbanization, return period and rainfall patterns at the downstream of Manchon urban watershed in TaeGu City. SWM(Storm Water Management Model) is used for runog analysis based on 5 different steps of urbanization and 4 different types of Hufrs quartile according to 8 return periods. It is analyzed that the order of total runoff yield according to raiun patterns is Huffs 4, Huffs 2. Huffs 3 and Huffs 1 quartile, that of peak flow magnitude is Huffs 2, Huffs 1, Huffs 4 and Huffs 3 quartile at present development ratio. under the 60, 70, 80 and 90ft of urbanization to the 50% of urbanization by means of the rainfall patterns, the mean Increasing ratio of total runoff yield for each case is 4.55, 11.43, 16.07 and 20.02%, that of peak flow is 5.82, 13.61, 17.15 and 18.83%, the mean decreasing ratio of peak flow travel time Is 0.00, 2.44, 5.07 and 6.26%, the mean increasing ratio of runoff depth Is 4.51, 11.42, 16.02 and 20.05% respectively. the mean increasing ratio of total runoff yield by means of each and 19.71%. Therefore, as the result of this study. it can be used for principal data as to storm sewage treatment and flood damage protection planning in urban small watershed.

• International Journal of Industrial Entomology and Biomaterials
• /
• 제4권2호
• /
• pp.143-147
• /
• 2002

Studies on the interrelationship between biological yield and harvest index, and their association with shoot rearing were carried out in 9 promising mulberry genotypes, which indicated significant variations among genotypes. Biological yield had close association with leaf yield components indicating that they are inter-related for higher productivity in mulberry, Biological yield revealed highly significant positive correlation with important leaf yield components. However height of the longest branch showed negative correlation with biological yield. Genotypes with higher biological yield associated with low ratio of stem weight to leaf weight and high Harvest index on dry weight basis are to be selected for shoot rearing. Biological yield recorded on fresh weight basis had less impact on the present study in comparison to dry weight basis.

• 한국초지조사료학회지
• /
• 제16권3호
• /
• pp.199-207
• /
• 1996

This experiment was canied out to determine the effects of seeding method and seeding ratio in mixed cropping of forage rye and red clover on dry matter yield, nutritional yield and chemical characteristics of soil. The main treatment was two seeding methods(drilling and broadcasting) and the sub treatment was six seeding ratios between rye and red clover(T1; 150kg : 0 kg/ha, T2; 120 : 3, T3; 90 : 6, T4; 60 : 9, T5; 30 : 12, T6; 0 : 15). The experiment was performed at the College of Natural Science of Kon-Kuk University in Chungju in 1992. The results were summarized as follows; 1. Protein content was increased by increasing the seeding ratio of red clover, but content of NDF and ADF were decreased. 2. The seeding method did not affects significantly the dry matter yield, but broadcasting showed higher dry matter yield than drilling in the same seeding ratio. Especially, T3 of broadcasting was the highest yield of 13, 172 kg/ha The T3 of broadcasting and T4 of drilling showed hlghly crude protein yield of 1, 268 kgha and 1, 252 kg/ha, respectively. 3. Comparing the each seeding ratio of two seeding method, total nitrogen yield of shoot and root of drilling were higher than broadcasting. Especially, T2 and T4 of drilling were the highest in total nitrogen yield. 4. There were more increase in organic matter and nitrogen contents but decrease in K, Ca of soil by increasing the seeding ratio of red clover than soil before experiment. In the seeding methods, broadcasting was an effect of soil improvement.

• Bulletin of the Korean Chemical Society
• /
• 제11권3호
• /
• pp.214-220
• /
• 1990

We have studied the Infrared Multiphoton Dissociation (IRMPD) of 1-bromo-3-chloropropane by using the pulsed $CO_2$ laser. The product yields and the HCl/HBr branching ratios in IRMPD of $BrCH_2CH_2CH_2Cl$ are studied under the focused beam geometry as a function of buffer gas (He) pressure, laser energy, and photolysing wavelength. It is observed that the total dissociation yield has a laser energy dependence of 1.8-2.0 power order and the branching ratio is very slightly dependent on the pulse energy for the laser lines employed. The dependences of total dissociation yield and branching ratio on the buffer gas pressures show that the dissociation yield monotonically decreases and the branching ratio slightly decreases with the increase of the buffer gas pressure. The Energy-Grained Master Equation (EGME) was applied to explain the laser pulse energy and the buffer gas pressure(He) dependence of the dissociation yield and the branching ratio.