• Journal of the Korea Convergence Society
• /
• v.10 no.5
• /
• pp.165-171
• /
• 2019

Engineering and Technology have been influencing a lot in the field of sports. Competitiveness, attributes of sports, have forced not only sports players but sports goods to enhance those performance. Particularly in the field of motorsports, the convergence of sports and technology has long been done to satisfy between performance and safety. In this study, strength analysis was carried with FEM to develop CFRP Laminate(Carbon Fiber Reinforced Plastic Laminate) bucket seat targeted to motorsports and car tuning industries and FIA($F\acute{e}d\acute{e}ration$ Internationale de l'Automobile) regulation was applied to design the racing seat and evaluate its strength. FEM modeling considered the attributes of composites was followed by strength evaluation based on Tsai-Wu failure index were done according to Lay-up sequence and layer numbers. The result showed that the lay-up sequence with stacking angle such as $[0^{\circ}/30^{\circ}/60^{\circ}/90^{\circ}/-30^{\circ}/-60^{\circ}]_4$ with 3mm form core was optimal selection in the field of weight and strength evaluation.

• The Journal of the Convergence on Culture Technology
• /
• v.5 no.2
• /
• pp.337-344
• /
• 2019

The purpose of this study men and women 20 to 30 of 16 patients wearing thick insoles 5cm before and after squat exercise based on the angle of the knee joint(0-, 60-, 90-degree) was to observe the muscle activities. For this through the analysis of the rectus femoris EMG, vatus medialis vatus lateralis, tibialis anterior, gastrocnemius MVIC were quantified using. The results following results were obtained. After wearing the thick insole standing position(0') had increased EMG activity of vastus lateralis muscle, the knee angle is rectus femoris, vatus medialis, vastus lateralis, tibialis anterior, gastrocnemius muscles were increased muscle activity. thick insole of the ankle joint, causing plantar flexion forward weight distritbution by focusing is normally the body would lead to an array. When an array of everyday life, these abnormalities increases energy consumption, and muscle fatigue, increase will cause an imbalance in the muscles. Therefore, wearing thick insoles by changing the activity of the muscles may cause knee pain.

• Journal of the Korea Convergence Society
• /
• v.10 no.4
• /
• pp.81-89
• /
• 2019

This study was analyzed about the relationship between culture microenvironment and cell differentiation of HPV 16 E6/E7-transfected immortalized oral keratinocyte(IHOK). By the alteration of culture environment, IHOK-EF and IHOK-EFKGM were obtained, and the modulation of cell properties was observed by cell proliferation assay, immunofluorescence, microarray, and quantitative real-time PCR analysis. IHOK-EF losed the properties of epithelial cells and obtained the properties of mesenchymal cells, and in the result of microarray analysis, genes related to the inhibition of differentiation such as IL6, TWIST1, and ID2 were highly expressed in IHOK-EF. When the culture environment was recovered to initial environment, these changes were recovered partially, presenting the return of genes involved in the inhibition of differentiation such as IL6, and ID2, particularly. This study will contribute to understand adjustment aspect for cell surviving according to the change of culture microenvironment in the study for determining the cell characteristic, and facilitate therapeutic approach for human disease by applying surviving study according to the change of cancer microenvironment.

• Journal of the Korea Convergence Society
• /
• v.12 no.1
• /
• pp.251-257
• /
• 2021

ln this study, natural extracts extracted from cypress sapiens, a natural material, were investigated as materials that could protect skin aging caused by ultraviolet rays, and experiments were conducted on the synthesis of filaggrins that make up the natural moisturizing factor of the skin, the synthesis of pro-colagen, a fibrous protein, which plays an important role in moisturizing the dermis, and elastin, which is an enzyme that decomposes collagen. As a result, cypress ethanol extract (COE) was a dependent inhibitor to collagenase and elastase, inhibiting the synthesis of filaggrin and the expression of MMP-1 for exfoliated cells damaged by ultraviolet rays. Therefore, it is estimated that ethanol extract will have the effect of delaying wrinkles and as a functional cosmetic material that inhibits skin aging convergence. Based on this study, we would like to further study the mechanism of the synthesis of filaggrin on the suppression of expression of MMP, which is the anti-wrinkle effect.

• Journal of the Architectural Institute of Korea Planning & Design
• /
• v.34 no.9
• /
• pp.129-140
• /
• 2018

The purpose of this study was to reconsider existing hypotheses on the orinination and changes of changbang-anchogongs and their types and suggest an alternative hypothesis. The earliest changbang-anchogongs in $17^{th}$ century is presumed to originate as imitations of chungbang ppaelmoks for ornamental and reinforcing parts for changbangs. They were framed whole sides of buildings equally, and were used in small numbers of extant royal buildings and Buddhist halls. From late $17^{th}$ century, enlarged dragon shape changbang-anchogongs applied to Buddhist halls maily to decorate and strengthen front side of buildings. As a result of exchange between changbang-anchogongs and Ikgong type brackets, combined changbang-anchogongs in Buddhist halls were invented for stronger connection with upper bracketing units and have been spread during $18^{th}$ century. Danpyeongbang anchogongs were originated by the connection between short pieces of pyeongbangs and early type of anchogongs similar to ppaelmoks. They belong to minority subtype, but were drawn in illustrations by mistake, as parts of main halls of royal palaces from $19^{th}$ century, because of painter's confusion about new techniques for changbang-anchogongs. Combined changbang-anchogongs for royal buildings were presumed to be invented in 1790s by stimulation from a Buddhist hall related to royal tomb. However, unlike Buddhist precedence, they were used to reinforce and decorate whole sides, even corners, of buildings, and their frameworks and shapes were imported from Daeryang-anchogongs at flanks of ritual halls in royal tombs and royal shrines from $17^{th}$ century.

• Journal of the Architectural Institute of Korea Planning & Design
• /
• v.35 no.8
• /
• pp.23-34
• /
• 2019

The façade, a fundamental function as a skin that protects human life from external environment such as cold and hot weather, snow, rain, and wind, etc, has served as a media for communication between indoor space of the building and outside space. From the media for communication point of view, the approach to envelope design, in which environmental elements are transmitted internally through the filtering of external environments, has been evolving in various ways from the past to the present. Today, modern architecture technologies including curtain wall systems and user-friendly computer programming and environmental analysis programs demonstrate a differentiated approach to envelope design related to the indoor environment. For this reason, it is worth noting that the envelope design factors and trends that appear variously in the UNStudio's projects before and after the 2000s. The factors reflected in the envelop design in conjunction with the indoor environment obtained through the case study of the UNStudio's office projects were daylight environment, thermal environment, ventilation, noise, privacy and view, and consideration for daylight environment and thermal environment was reflected in many cases through the case study. Looking at the changes in the diagrams in order of year, it can be seen that the envelope design using the environmental analysis tool has been performed since 2006. This is a clue to show the envelop design changes from the conceptual method to the data-based one. The diagrams and analysis results related to the envelop design showed that the thermal environment related to solar radiation was the most, and no diagrams and analysis related to the indoor illumination were found. Since 2010, PV panel installation has been shown in the envelope design, which can be found in the increased efficiency of PV panels due to the technological advances and the decrease in production cost.

• Journal of the Architectural Institute of Korea Planning & Design
• /
• v.35 no.11
• /
• pp.69-78
• /
• 2019

The purpose of this study is to propose a modeling methodology through the exchange of coordinate data of a three-dimensional custom curtain wall panel between Rhino and Revit, and to examine the validity of the model implemented in the drawing. Although the modeling means and method are different, a fundamental principle is that all three-dimensional modeling begins by defining the position of the points, the most primitive element of geometry, in the XYZ coordinate space. For the BIM modeling methodology proposal based on this geometry basic concept, the functions and characteristics associated with the points of Rhino and Revit programs are identified, and then BIM implementation process model is organized and systemized through the setting of the interoperability process algorithm. The BIM implementation process model proposed in this study is (1) Modeling and panelizing surface into individual panels using Rhino and Grasshopper; (2) Extraction of vertex coordinate data from individual panels and create CSV file; (3) Curtain wall modeling through Adaptive Component Family in Revit and (4) Automatic creation of Revit curtain wall panels through API. The proposed process model is expected to help reduce design errors and improve component and construction quality by automatically converting general elements into architectural meaningful information, automating a set of processes that build them into BIM data, and enabling consistent and integrated design management.

• Journal of the Architectural Institute of Korea Planning & Design
• /
• v.35 no.11
• /
• pp.13-24
• /
• 2019

The history of tall buildings begins in 1853with the development of elevators. After the Industrial Revolution of the 18th century, the development of high-rise buildings will be carried out in earnest as a means to efficiently use the limited land of cities. The development, which began around Chicago, extended over a long period of time to Asia, maximizing the high competition. However, in the 2000s, not only was it high due to the development of construction and digital technology, but it also became competitive in eco-friendly elements and unstructured forms. High-rise building plans that have gained elemental and morphological diversity are completed by the interrelationships of various plans. Among them, it is important that the core plan has a reasonable approach from the initial planning stage as the basis for the vertical copper plan linking vertically-intensive functions. The cores should be designed to be clear and adequately responsive to changes in the shape of the building. This study aims to provide designers with a reasonable understanding of core planning by identifying core characteristics of irregular high-rise. In particular, we want to analyze the shape of the ground layer core and the relationship between the area and components of the ground layer core. The analysis results are as follows, classified according to the type or use of the building. Of the atypical forms composed of double bending, the TAPER-Curve and TWIST forms are the most distributed, and the plane and core shapes of the ground floor are the most commonly used. Based on the analysis of the validity of the ground floor cores by shape of the cores, the most commonly used forms for core shapes in the planning of the atypical high-rise are square, circular and Oval, and the most efficient oval cores and relatively inefficient ones when planned.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.3
• /
• pp.74-79
• /
• 2021

This study examined the mixing efficiency of exhaust gas and urea according to the mixer shape in the SCR system. For the experiment, an SCR simulation system was manufactured, and a uniformity detector was attached to the catalyst location to measure the uniformity. The experiment was conducted by setting the exhaust-gas flow rate, temperature, mixer type, and catalyst distance as variables. The experimental results confirmed the swirl angle analysis, urea number distribution, and uniformity. The swirl angle experiment of Models A and B confirmed that the swirl angle of Model A was formed approximately 7 to 8 degrees higher over the entire RPM range. When there was no mixer in the SCR system, the urea and water were concentrated to one side. Mixer Model A showed an even distribution overall, and Model B showed a slightly concentrated tendency at the beginning but then showed a stable distribution of urea. The mixing efficiency of 90%, which was the uniformity target, could be satisfied in Model A and Model B. In particular, Model A showed excellent results that satisfied 90% efficiency at 10 cm of the catalyst position.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.24 no.3
• /
• pp.33-47
• /
• 2021

This study was conducted to investigate the influence of eco-friendly restoration in forested bog on the structure of benthic macroinvertebrate community. The benthic macroinvertebrates collected from the surveyed sites were composed of 1,071 individuals, 60 species, 40 families, 13 orders, 6 classes and 5 phyla. At the control and Site 3(small dam), the number of species and individuals were larger than that of other sites, and EPT group ratio was same as well. Considered by index, the dominance index (DI) was found the highest at the biotope area. The diversity index (H') and richness index (RI) were the highest at the control and Site 3. In addition, the ecological score of benthic macroinvertebrate (ESB) showed the highest at site 3, while the lowest at biotope area. The stability and recovery of benthic macrointebrates showed different according to restoration types at forested bog. After restoration project, the benthic macroinvertebrates were observed to get recovery at Site 3, and to have the highest communities stability at control and Site 3. At biotope areas (Site 4, Site 5 and Site 6) communities stability were the lowest, but showed different community stability values according to the presence of water. It is confirmed that the eco-friendly restoration projects indeed provided the better environment for the inhabitation of benthic macroinvertebrate community. The change of community index depending on the restoration projects suggests that the eco-friendly restoration can provide a more suitable environment for benthic macroinvertebrate ecosystem that prefers the stream environment.