• Korean Journal of Computational Design and Engineering
• /
• v.9 no.4
• /
• pp.277-285
• /
• 2004

In this paper, a 2 DOF haptic yawing joystick for use as the navigation input device in virtual environments is introduced. The haptic yawing joystick has 360° range for yawing motion and ±100° for pitching motion. The device can support weights of up to 26N for χ axis and 10N for axis with 10kHz of sampling rate. The size of the haptic yawing joystick is so small that it can be assembled on armrest of an arm chair and has relatively larger work space than other conventional 2 DOF joysticks. For the haptic yawing joystick, an ellipse navigation algorithm using the user's velocity in the virtual navigation is proposed. The ellipse represents the velocity of the user. According to the velocity of the navigator, the ellipse size is supposed to be changed. Since the path width of navigation environments is limited, the ellipse size is also limited. The ellipse navigation algorithm is tested in 2 dimensional virtual environments. The test results show that the average velocity of the navigation with the algorithm is faster than the average navigation velocity without the algorithm.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.24 no.4
• /
• pp.426-434
• /
• 2021

In this paper, three-dimensional unsteady computational fluid dynamic(CFD) analyses based on overset grid technique have been performed for a hand-launched unmanned aerial vehicle(UAV) considering the wake effect generated by a rotating propeller. In addition, the defection of rudder is considered in order to consider to predict the equilibrium condition of yawing moment during cruise flight conditions. It is importantly shown in this paper that the wake interference effect of the propeller is significant to accurately predict the yawing moment of the UAV and the yawing moment coefficient corresponding to a flight speed can be different because of its different amount of wake effect due to the different rotating speed of the propeller.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.5 no.2
• /
• pp.62-71
• /
• 2002

A free oscillation technique for obtaining the dynamic stability derivatives in yaw is applied to the pure yawing motion. The procedure of wind tunnel testing is to compute the derivatives after measuring deflecting angles of the model during the free oscillating motion. The charging compressed air is supplied for the initial excitation. The results of this experiment predicted feasible characteristics of the yawing motion, comparing with the data previously reported in the literature.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.485-486
• /
• 2008

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.11
• /
• pp.1130-1136
• /
• 2009

A new control algorithm for the yaw motion control of a unicycle robot has been proposed in this paper. With the increase of life quality, there are various transportation systems such as segway and unicycle robot which provide not only transportation but also amusement. In most of the unicycle robots share the same technology in that the directions of roll and pitch are controlled by the balance controllers, allowing the robots to maintain balance for a long period by continuously moving forward and backward. However, one disadvantage of this technology is that it cannot provide the capability to the robots to avoid obstacles in their path way. This research focuses to provide the yawing function to the unicycle robot and to control the yaw motion to avoid the obstacles as desired. For the control of yawing motion, the yaw angle is adjusted to the inertia generated by the velocity and torque of a yawing motor which is installed in the center axes of the unicycle robot to keep the lateral control simple. Through the real experiments, the effective and robustness of the yawing control algorithm has been demonstrated.

• Journal of IKEEE
• /
• v.26 no.4
• /
• pp.602-613
• /
• 2022

This paper proposes an algorithm for correcting indirect situations resulting from the wheelchair moving the stairs with wheel-type caterpillar and seat position variable. For analyzing the Yawing movement model, the change of Yaw value was estimated using Roll, Pitch, and Yaw in the driving environment, and it was used as a control variable and the information of the wheel drive controller. The verification confirmed the correction of about 10° of Yawing movement within about 7 seconds. It was confirmed that the angular velocity was reduced by 47.5% in seat position change.

• Journal of the Society of Naval Architects of Korea
• /
• v.49 no.4
• /
• pp.327-332
• /
• 2012

International Towing Tank Conference (ITTC) recommended verifying a ship's ability to move transversely at zero forward speed without altering heading by a crabbing test. In sea trial, all available propellers/rudders/thrusters should be used to find the maximum possible transverse speed. For estimating crabbing ability in the design stage, tests to estimate possible swaying force and yawing moment range using all available propellers/rudders/thrusters are conducted. By butterfly diagram, which compares possible swaying force and yawing moment range with external swaying force and yawing moment by wind, a ship's crabbing ability can be estimated. In this study, model tests of a cruise vessel equipped with bow thrusters and POD system were conducted to find out her crabbing ability in the design stage. To mimic quay condition, a model quay-wall was set in the towing tank.

• Proceedings of the KSR Conference
• /
• 2003.10c
• /
• pp.500-506
• /
• 2003

Dopper should performance not only to constrain rolling and yawing system but also to develop capability of pantograph. In orde to get purpose, the survey and study that the type of dropper which convert 'I' type dropper into 'Y' type that performance to constrain rolling,yawing and jamping of catenary system simultaneously.

• The korean journal of orthodontics
• /
• v.47 no.3
• /
• pp.195-206
• /
• 2017

Facial asymmetry can be classified into the rolling-dominant type (R-type), translation-dominant type (T-type), yawing-dominant type (Y-type), and atypical type (A-type) based on the distorted skeletal components that cause canting, translation, and yawing of the maxilla and/or mandible. Each facial asymmetry type represents dentoalveolar compensations in three dimensions that correspond to the main skeletal discrepancies. To obtain sufficient surgical correction, it is necessary to analyze the main skeletal discrepancies contributing to the facial asymmetry and then the skeletal-dental relationships in the maxilla and mandible separately. Particularly in cases of facial asymmetry accompanied by mandibular yawing, it is not simple to establish pre-surgical goals of tooth movement since chin deviation and posterior gonial prominence can be either aggravated or compromised according to the direction of mandibular yawing. Thus, strategic dentoalveolar decompensations targeting the real basal skeletal discrepancies should be performed during presurgical orthodontic treatment to allow for sufficient skeletal correction with stability. In this report, we document targeted decompensation of two asymmetry patients focusing on more complicated yaw-dependent types than others: Y-type and A-type. This may suggest a clinical guideline on the targeted decompensation in patient with different types of facial asymmetries.

• The Journal of Korea Robotics Society
• /
• v.3 no.4
• /
• pp.331-337
• /
• 2008

The field of robots is being widely accepted as a new technology today. Many robots are produced continuously to impart amusement to people. Especially the robot which operates with a wheelbarrow was enough of a work of art to arouse excitement in the audiences. All the wheelbarrow robots share the same technology in that the direction of roll and pitch are acting as balance controllers, allowing the robots to maintain balance for a long period by continuously moving forward and backward. However one disadvantage of this technology is that they cannot avoid obstacles in their way. Therefore movement in sideways is a necessity. For the control of rotation of yawing direction, the angle and direction of rotation are adjusted according to the velocity and torque of rotation of a motor. Therefore this study aimed to inquire into controlling yawing direction, which is responsible for rotation of a robot. This was followed by creating a simulation of a wheelbarrow robot and equipping the robot with a yawing direction controlling device in the center of the body so as to allow sideway movements.