• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.6
• /
• pp.59-67
• /
• 2014

A numerical model and a controller of Active Front wheel Steer (AFS) system are designed in this study. The AFS model consists of four sub models, and the AFS controller uses sliding mode control and PID control methods. To test this model and controller an Integrated Dynamics Control with Steering (IDCS) system is also designed. The IDCS system integrates an AFS system and an ARS (Active Rear wheel Steering) system. The AFS controller and IDCS controller are compared under several driving and road conditions. An 8 degree of freedom vehicle model is also employed to test the controllers. The results show that the model of AFS system shows good kinematic steering assistance function. Steering ratio varies depends on vehicle velocity between 12 and 24. Kinematic stabilization function also shows good performance because yaw rate of AFS vehicle tracks the reference yaw rate. IDCS shows improved responses compared to AFS because body side slip angle is also reduced. This result also proves that AFS system shows satisfactory result when it is integrated with another chassis system. On a split-m road, two controllers forced the vehicle to proceed straight ahead.

• Journal of Auto-vehicle Safety Association
• /
• v.5 no.2
• /
• pp.32-38
• /
• 2013

This paper presents collision avoidance using model predictive control algorithm. A model predictive control algorithm determines lateral tire force and yaw moment and steering angle input and differential braking input is determined from lateral tire force and yaw moment. A constraint for model predictive control is designed for obstacle avoidance. A objective function is designed to minimize lateral tire force and yaw moment input and to follow changed lane after collision avoidance. The performance of proposed algorithm has been investigated via computer simulation conducted to vehicle dynamic software CARSIM and Matlab/Simulink.

• Journal of Power System Engineering
• /
• v.8 no.4
• /
• pp.57-63
• /
• 2004

Conventionally, 2WS is used for vehicle steering, which can only steering front wheel. In case of trying to high speed lane change or cornering through this kind of vehicle equipped 2WS, it may occur much of Yaw moment. On the other hand, 4WS makes decreasing of Yawing Moment, outstandingly, so it is possible to support vehicle movement stable. And conventional ABS and TCS can only possible to control the longitudinal movement of braking equipment and drive which can only available to control of longitudinal direction. There after new braking system ESP was developed, which controls both of longitudinal and lateral, with adding of the function of controlling Active Yaw Moment. On this paper, we show about not only designing of improved braking and steering system through establishing of the integrated control system design of 4WS and ESP but also designing of the system contribute to precautious for advanced vehicle stability problem.

• Wind and Structures
• /
• v.6 no.1
• /
• pp.53-70
• /
• 2003

Tsing Ma Bridge in Hong Kong is the longest suspension bridge in the world carrying both highway and railway. It has two H-shape concrete towers, each of which is composed of two reinforced concrete legs and four deep transverse prestressed concrete beams. A series of wind tunnel tests have been performed to measure the aerodynamic coefficients of the tower legs and transverse beams in various arrangements. A 1:100 scaled 3D rigid model of the full bridge tower assembled from various tower components has been constructed for different test cases. The aerodynamic coefficients of the lower and upper segments of the windward and leeward tower legs and those of the transverse beams at different levels, with and without the dummy bridge deck model, were measured as a function of yaw wind angle. The effects of wind interference among the tower components and the influence of the bridge deck on the tower aerodynamic coefficients were also investigated. The results achieved can be used as the pertinent data for the comparison of the computed and field-measured fully coupled buffeting responses of the entire bridge under yaw winds.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.2
• /
• pp.81-86
• /
• 2013

This paper presents the lane change system for collision avoidance. The proposed algorithm for the collision avoidance consists of path generation and path following. Using a calculated TTC (Time to Collision), partial braking is operated and collision avoidance path is generated considering relative distance, velocity and acceleration. Based on the collision avoidance path, desired yaw angle and yaw rate are calculated for the automated path following. The lateral controller is designed by a Lyapunov function approach using 3 D.O.F vehicle model and vehicle parameters. The required steering angle is determined from wheel velocity, longitudinal and lateral velocity in order to follow the desired yaw angle and yaw rate. This system is developed MATLAB/Simulink and its performance is evaluated using the commercial software CarSim.

• International Journal of Aeronautical and Space Sciences
• /
• v.10 no.2
• /
• pp.43-51
• /
• 2009

In the flight of air vehicles, accurate air data information is required to control them effectively. Especially, helicopters are often put in drastic motion involved with high angle of attacks in order to perform difficult missions. Among various sensors, the multi function probe (MFP) has been used in the present study mainly owing to its advantages in structural simplicity and capability of providing various information such as static and total pressure, speed, and pitch and yaw angles. In this study, a five-hole multi-function probe (FHMFP) is developed and its calibration is conducted using multiple regressions. In this work a calibration study on the FHMFP, an air data sensor for helicopters, is reported. It is shown that the pitch and yaw angles' accuracy of calibration is ${\pm}0.91^{\circ}$ at a cone angle of $0^{\circ}{\sim}30^{\circ}$ and ${\pm}2.0^{\circ}$ at $30^{\circ}{\sim}43^{\circ}$, respectively, which is summarized in table 3.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.4
• /
• pp.121-129
• /
• 2000

this paper develops a computational model for the turning maneuver analysis of a cabover type heavy truck. The model having 42 degree-of-freedom is developed using ADAMS. Leaf springs used in the front and rear suspension systems are modeled by dividing it three links and joining them with joints. Force and displacement relationship showing nonlinear hysteric characteristics of the leaf spring is measured and modeled with an exponential function. A velocity and force relationship of a shock absorber is measured and modeled with a spline function. And a stabilizer bar is modeled using ADAMS beam element to consider a twisting and bending effect. To verify the developed model an actual vehicle test is performed in the double lane change course with 50kph and 60kph vehicle velocity. In the actual vehicle test lateral acceleration roll angle and yaw rate are measured, The tendency and peak-to-peak values of the actual vehicle test and simultion results are compared each other.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.3
• /
• pp.43-52
• /
• 2010

In this study, the shapes of the wheel and rail are represented by using 3-dimensional surface functions with surface parameters and a 3-dimensional wheel-rail contact analysis is presented. A whole numerical solution of wheel-rail contact at tread and flange including 2-point contacts can be achieved with the proposed numerical algorithm. Kinematic characteristics such as variances of vertical displacement and roll angle, and variance of wheel radius difference for arbitrary yaw and lateral displacement of wheelset, are determined for the KTX wheel-rail pair as an example. The condition of yaw and lateral displacement occurring 2-point contacts to analyze derailment are compared between standard and worn wheels. Differences of contact characteristics between curved and straight rails are also analyzed.

• 유체기계공업학회:학술대회논문집
• /
• 2000.12a
• /
• pp.193-199
• /
• 2000

The effects of Reynolds number on the non-nulling calibration of a cone-type five-hole probe in low-speed flows have been investigated at the Reynolds numbers of $2.04{\times}10^3,\;4.09{\times}10^3$, and $6.13{\times}10^3$. The calibration is conducted at the pitch and yaw angles in ranges between -35 degrees and 35 degrees with an angle interval of 5 degrees. The result shows that each calibration coefficient, in general, is a function of the pitch and yaw angles, so that the pre-existing calibration data in a nulling mode are not enough in accounting for the full non-nulling calibration characteristics. Due to the interference of the probe stem, the calibration coefficients have more Reynolds number sensitivity at positive pitch angles than at negative ones.

• 제어로봇시스템학회:학술대회논문집
• /
• 1994.10a
• /
• pp.601-604
• /
• 1994

This paper describes an effective method to estimate a position of an automous vehicle equipped with a single CCD-camera along indoor passageways. Using the sequential image data from the self-movement of the vehicle, the position is estimated by integrating the approximated motion parameters. The detection of the yaw angle that is one of the motion parameter is difficult in general, e.g. slip or error for noise, therefore the different detection is presented, which is, without shaft encoders, based on a projection function for 2D-image data and a cross-correlation function so as to be robust for noise. The approximated geometric function to estimate the position is used to reduce the computational effort. To verify the effectiveness of the method, the analysis and the computational results are shown through the simulations. Furthermore, the experimental results by using the test vehicle for the real indoor passageway are shown.