• Progress in Superconductivity
• /
• 제6권2호
• /
• pp.133-137
• /
• 2005

We fabricated the Au/Ni template for YBCO coated conductors and evaluated texture formation and the microstructural evolution. The cube textured Ni substrate was fabricated by rolling and recrystallization annealing, and subsequently Au layer formed on the substrate by electroless-plating method. The texture was evaluated by pole-figure with x-ray goniometer with orientation distribution function (ODF) analysis. The surface roughness and grain boundary morphology of template were characterized by atomic force microscopy (AFM) We observed that Au layer deposited epitaxially on Ni substrate and formed a strong cube texture when plating time was optimized. The full-width at half-maximum (FWHM) was $8.4^{\circ}$ for out-of-plane and $9.98^{\circ}$ for in-plane texture for plating time of 30 min. Microstructural observation showed that the Au layer was homogeneous and dense without formation of crack/microcrack. In addition, we observed that root-mean-square (RMS) and depth of grain boundary were 14.6 nm and 160 $\AA$ for the Au layer, respectively, while those were 27.0 nm and 800 $\AA$ for the Ni substrate, indicating that the electoless-plated Au layer had relatively smooth surface and effectively mollified grain groove.

• Progress in Superconductivity
• /
• 제7권2호
• /
• pp.135-139
• /
• 2006

We fabricated YBCO coated conductors (CCs) by TFA-MOD process and evaluated microstructure, texture formation, and critical temperature ($T_c$) and current ($I_c$). YBCO precursor solution was synthesized using metal-trifluoroacetates and dip coated on $LaAlO_3$(LAO) substrate. The phase formation and microstructure was characterized by X-ray diffraction and scanning electron microscopy (SEM) and the degree of texture was evaluated by pole-figure analysis. The CC was heat-treated in various calcining temperatures ($370^{\circ}C-460^{\circ}C$) and firing temperatures ($750^{\circ}C-800^{\circ}C$). As fired at $775^{\circ}C$ for 4h, the CC had the highest $T_c$ of 89.5 K and $I_c$ of 40 A/cm-width ($J_c=2.0\;MA/cm^2$). Microstructural observation indicated that the YBCO film was dense and homogeneous and had a strong cube texture without formation of second phase and its in-plane full-width at half-maxima; $5.2^{\circ}$ under optimum condition.

• 한국재료학회지
• /
• 제9권11호
• /
• pp.1049-1054
• /
• 1999

근사단결정 다이아몬드막 성장시 입자의 정렬을 개선하기 위한 집합조직성장의 2단계 성장방법을 제안하였다. 메탄조성 4%, 기판온도 $850^{\circ}C$ 조건에서 (100) Si 기판에 - 200V 바이어스를 인가하여 20분동안 전처리 하였다. 처리한 기판을 2%[CH$_4$], 기판온도 $810^{\circ}C$에서 2~35시간동안 <100> 집합조직을 지니도록 1단계로 성장시켰다. 이 시편의 성장표면을 평탄화하기 위하여 (100) 면이 성장하도록 2% [CH$_4$], 기판온도 $850^{\circ}C$ 조건에서 2단계 성장시켰다. 1단계 성장시간에 따른 다이아몬드막의 배열정도를 {111} X-ray pole figure의 반가폭 변화를 통해 관찰하였다. 1단계 성장 후 입자정렬은 막의 두께가 증가할수록 개선되었다. 그러나 <100> 집합조직의 표면조직은 피라미드 형태의 굴곡을 피할 수 없었다. 2단계 성장시 (100) 면의 성장으로 인해 막의 표면은 평탄화되었으며, 이때 입자의 정렬은 1단계 성장시간에 크게 의존하였다.

• 열처리공학회지
• /
• 제21권3호
• /
• pp.144-149
• /
• 2008

It has been reported that copper and copper alloys have a large anisotropy of functional properties such as electrical, thermal and mechanical properties, which means that the texture of polycrystalline alloy should be considered to achieve better properties. In this study, the determination of grain growth orientation and texture formation in the cold-rolled, heat-treated and Ni-plated hybrid copper sheets was investigated. Grain growth direction and texture formation were analyzed by the X-ray pole figure. The influence of texture on the mechanical properties could be quantitatively confirmed by the results from the orientation distribution function and the tensile test. The heat-treated texture in the cold-rolled hybrid copper sheet is also investigated and discussed.

• 한국진공학회지
• /
• 제5권2호
• /
• pp.133-138
• /
• 1996

단일 선구물질인 1, 3 -디실라부탄을 사용하여 고진공 하의 온도 영역 900-$1000^{\circ}C$에서 탄화규소 환충층이 형성된 Si(001) 기질 위에 입방형 탄화규소 박막을 적층 성장시켰다. 얻어진 탄화규소 박막의 화학량론적 비, 양질의 결정성 및 표면형태의 특성을 반사 고에너지 전자 회절, Xtjs 광전자 분광법, X선 회절, Xtjs 극접도, 주사 전자 현미경 및 투과 전자 현미경으로 확인하였다. 이들 결과로부터 단일 선구물질인 1, 3-디실라부탄이 입방구조를 가지는 탄화규소 박막의 적층 성장에 적절한 물질임을 밝혔다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.II
• /
• pp.1576-1579
• /
• 2005

With varying rapid thermal annealing (RTA) temperature, luminescence properties of $Zn_{0.75}Mg_{0.25}S:Mn$ thin film deposited by RF-magnetron sputtering technique were investigated. In this study, $Zn_{0.75}Mg_{0.25}S:Mn$ thin film phosphor showed more red emission than those of the previous studies when annealed around 600 or $650^{\circ}C$. Although all samples were deposited from identical source composition, a main peak wavelength of photoluminescence spectra of $Zn_{0.75}Mg_{0.25}S:Mn$ shifted toward shorter wavelengths depending upon increase of RTA temperature. The same dependence of wavelength on RTA temperature was also observed in cathodoluminescence as well as electroluminescence measurements. It was revealed that the change of the luminescence properties were originated from structural changes in $Zn_{0.75}Mg_{0.25}S:Mn$ thin film phosphor from cubic to hexagonal phases analyze using conventional X-ray pole figure mapping. The phase transition would be the origin of luminescence property changes with respect to RTA temperature.

• 한국분말재료학회지
• /
• 제14권1호
• /
• pp.13-18
• /
• 2007

The mother Ni-W (1-5 wt.%) alloy billets for coated conductor substrate were fabricated by powder metallurgy process. The tensile test results for the sintered Ni-W rods showed the increase of mechanical strength and decrease of ductility with increasing W content due to the solid solution hardening. All the fracture surfaces of the tested specimens showed the typical ductile fracture mode of dimple rupture due to the local necking. The Ni-W alloy billets were made into tape by cold rolling. After the appropriate heat treatment for recrystallization, the brass texture formed by the cold rolling was converted to the complete cube texture. The in-plane and out of plane texture of the tapes estimated by x-ray pole figure were smaller than 9 degree and 7 degree, respectively. The effect of the W addition on the texture development seems not to be significant.

• 한국초전도ㆍ저온공학회논문지
• /
• 제4권2호
• /
• pp.5-10
• /
• 2002

Deposition condition of NiO that is one of Possible buffer layers for YBCO coated conductors was studied. NiO was deposited on textured Ni substrates by a MOCVD (metal-organic chemical vapor deposition) method. The degree of texture, and the surface roughness were analyzed by X-ray Pole figure, atomic force microscope and scanning electron microscope. The (111) and (200) textures were competitively developed , depending on an oxygen partial Pressure(PO2) and deposition temperature (Tp). The (200) textured NiO layer was deposited at Tp=450~47$0^{\circ}C$ and PO2= 1.67 Torr Out-of-Plane ($\omega$-scan) and in-plane ($\Phi$-scan) textures of the (200) NiO films were as good as 10.34$^{\circ}$ and 10.00$^{\circ}$ respectively The AFM surface roughness of NiO was in the range of 3~4.5 nm at PO2=0.91~3.34 Torr and at Tp=47$0^{\circ}C$ , and in the range of 3~13 nm at TP=450~53$0^{\circ}C$ and at PO2=1.67 Torr.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 초전도 자성체
• /
• pp.59-63
• /
• 2002

The purpose of this paper is to investigate the crystal texture of the 2223 phase and its relationship with PIT processing parameter. Ag-sheathed Bi-2223 multi-filament tapes were prepared by changing rolling reduction ratio. We analysed the degree of texture for 2223 phase after heat-treatment. According to X-ray pole-figure, the texture of the filaments located near surface and center were not so different each other for all rolling conditions. we found a little higher degree of texture for 60% rolling reduction. But its difference is not so high compared with those tapes with a lower rolling reduction ratio. Reaction induced texturing seemed to contribute with a large portion under present condition.

• 한국분말재료학회지
• /
• 제10권4호
• /
• pp.241-248
• /
• 2003

Biaxially textured Ni tapes were fabricated by a cold working and recrystallization heat treatment processes from powder compact rods. The processing parameters associated with the cube texture formation in Ni tapes were systematically investigated by using X-ray diffraction and pole-figure analysis. The Ni powder used in this study was 5 $\mu$m in size and 99.99% in purity. To find the optimum sintering temperature, tensile tests were performed for Ni rods sintered at various temperatures. The Ni rods sintered at 100$0^{\circ}C$ showed poor elongation and low fracture strength, while the Wi rods sintered above 100$0^{\circ}C$ revealed good mechanical properties. The higher elongation and fracture strength of the Ni rods sintered at higher temperatures than 100$0^{\circ}C$ are attributed to the full densification of the sintered rods. The sintered Ni rods were cold-rolled with 5% reduction to the final thickness of 100 $\mu$m and then annealed for development of rube texture in rolled Ni tapes. The annealed Ni tapes depicted strong cube texture with FWHM(full-width at half-maximum) of in-plane and out-of-plane in the range of 8$^{\circ}$ to 10$^{\circ}$. The NiO deposited on the Ni tapes by MOCVD process showed good epitaxy with FWHM=10$^{\circ}$, which indicates that the Ni tapes can be used as a substrate for YBCO coated conductors.