• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.310-313
• /
• 2002

Structures obtained with a direct boning of two FZ silicon wafers joined in such a way that a smooth surface of one wafer was attached to the grooved surface of the other were studied. A square net of grooves was made with a conventional photo lithography process. After high temperature annealing the appearance of voids and the rearrangement of structural defects were observed with X-ray diffraction topography techniques. It was shown that the formation of void free grooved boundaries was feasible. In the cases when particulate contamination was prevented, the voids appeared in the grooved structures could be eliminated with annealing. Since it was found that the flattening was accompanied with plastic deformation, this deformation was suggested to be intensively involved in the process of void removal. A model was proposed explaining the interaction between the structural defects resulted in "a dissolution" of cavities. The described processes may occur in grooved as well as in smooth structures, but there are the former that allow to manage air traps and undesirable excess of dislocation density. Grooves can be paths for air leave. According to the established mechanisms, if not outdone, the dislocations form local defect arrangements at the grooves permitting the substantial reduction in defect density over the remainder of the interfacial area.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.211-211
• /
• 2011

Nanostructures, with a diversity of shapes, built on substrates have been developed within many research areas. Lithography is one powerful, but complex, technique to make structures at the nanometer scale, such as platinum nanowires for studying CO catalytic reactions [1], or aluminum nanodisks for studying the plasmon effect [2]. In this work, we approach a facile method to construct nanostructures using noble metals on a titania thin film by using self-assembled structures as a pattern. Here, a large-scale silica monolayer is transferred to the titania thin film substrates using a Langmuir-Blodgett trough, followed by the deposition of a thin transition metal layer. Owing to the hexagonal close-packed structure of the silica monolayer, we would obtain a metal nanostructure that includes separated metallic triangles (islands) after removing the patterning silica beads. This nanostructure can be employed to investigate the role of metal-oxide interfaces in CO catalytic reactions by changing the patterning silica particles with different sizes or by replacing the oxide support. The morphology and chemical composition of the structure can be characterized by scanning electron microscopy, atomic force microscopy and X-ray photoelectron spectroscopy. In addition, we modify these islands to a connected island structure by reducing the silica size of the patterning monolayer, which is utilized to generating hot electron flow based on the localized surface plasmon resonance effect of the metal nanostructures.

• 한국분말재료학회지
• /
• 제9권4호
• /
• pp.267-272
• /
• 2002

The production of micro components is one of the leading technologies in the fields of information and communiation, medical and biotechnology, and micro sensor and micro actuator system. Microfabrication (micromachining) techniques such as X-ray lithography, electroforming, micromolding and excimer laser ablation are used for the production of micro components out of silicon, polymer and a limited number of pure metals or binary alloys. However, since the first development of microfabrication technologies there have been demands for the cost-effective replication in large scale series as well as the extended range of available material. One such promising process is micro powder injection molding (PIM), which inherits the advantages of the conventional PIM technology, such as low production cost, shape complexity, applicability to many materials, applicability to many materials, and good tolerance. This paper reports on a fundamental investigation of the application of W-Cu powder to micro metal injection molding (MIM), especially in view of achieving a good filling and a safe removal of a micro mold conducted in the experiment. It is absolutely legitimate and meaningful, at the present state of the technique, to continue developing the micro MIM towards production processes for micro components.

• 대한기계학회논문집A
• /
• 제34권7호
• /
• pp.859-866
• /
• 2010

본 연구에서는 다단 마이크로 구조물의 대량성형을 위하여, 모듈화된 초소형몰드 시스템(MSMS)을 이용한 초소형 사출성형 공정을 수행하였다. 본 연구에서 적용된 초소형몰드 시스템은 여러 모듈들로 구성되어 있으며, 각 모듈들은 다양한 단면 마이크로 구조물을 가지고 있다. 초소형몰드 시스템의 모듈들은 X-선 리소그래피 공정 및 니켈 전주도금 공정으로 제작되었으며, 다양한 모듈들을 조합 및 결합함으로써 복잡한 형상을 가지는 초소형몰드 시스템을 효과적으로 구현할 수 있다. 이와 같은 초소형몰드 시스템을 적용함으로써, 본 연구에서는 다단 구조물의 표면에 마이크로 삼각 프리즘이 주기적으로 배열되어 있는 다단 마이크로 구조물의 초소형 사출성형 공정을 성공적으로 수행하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.469-469
• /
• 2011

고효율 염료감응형 태양전지(DSSC, Dye-Sensitized Solar Cell)의 구현을 위해서 유용한 방법중 하나는 정렬된 기공 (pore)을 $TiO_2$막 내에 형성시키는 것이다. 메조포러스 (mesoporous) $TiO_2$막은 dip coating이나 spin coating과 같은 방법으로 주로 증착되고 있으며, P123이나 F127과 같은 amphiphilic triblock copolymer를 메조포러스 구조를 만들기 위한 뼈대로 사용하고 있다. 또한, 이렇게 생성된 구조에서 amphiphilic triblock copolymer는 열처리 공정을 통하여 쉽게 제거될 수 있다. 고효율 태양전지를 구현하는 또 다른 방법으로는 패턴 된 기판을 사용하는 것이다. 패턴 된 기판은 빛의 반사를 억제하여 흡수율을 높이는 역할을 한다. 그러나 패턴 된 기판 위에서 메조포러스 $TiO_2$막의 형성에 관한 연구는 부족한 실정이다. 본 연구에서는 spin coating 방법으로 패턴 된 Si (111) 기판 위에 메조포러스 $TiO_2$를 성장하고 그 미세구조를 분석하였다. 패턴 된 기판은 nanosphere lithography(NSL) 법으로 mask를 증착한 후 건식 식각 (dry etching) 공정을 통해서 제작되었으며, 마스크와 불순물 등 은 초음파 세척 등으로 제거되었다. 메조포러스 $TiO_2$막은 1-propanol, P123, titanium isopropoxide와 HCl을 섞어 만든 용액으로 1 cm${\times}$1 cm 기판 위에 3000 rpm과 4000 rpm으로 각각 증착하였으며, 5일 동안 4도에서 에이징한 후 350도에서 3시간 열처리하였다. 이렇게 형성한 메조포러스 막의 형상과 미세구조적 특성이 주사전자현미경(SEM, scanning electron microscope), X-선 회절(XRD, X-ray diffraction) 등을 이용하여 연구되었다. 특히, 증착 조건에 따른 메조포러스 $TiO_2$박막의 형성 기구에 관한 고찰이 진행되었다. 나아가, $TiO_2$박막과 패턴 사이에 형성되는 계면 구조에 관한 연구를 투과전자현미경을 이용하여 진행하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.285-285
• /
• 2011

EUVL (Extreme Ultra Violet Lithography) is one of competitive lithographic technologies for sub-30nm fabrication of nano-scale Si devices that can possibly replace the conventional photolithography used to make today's microcircuits. Among the core EUVL technologies, mask fabrication is of considerable importance since the use of new reflective optics having a completely different configuration compared to those of conventional photolithography. Therefore new materials and new mask fabrication process are required for high performance EUVL mask fabrication. This study investigated the etching properties of SnO2 (Tin Oxide) as a new absorber material for EUVL binary mask. The EUVL mask structure used for etching is SnO2 (absorber layer) / Ru (capping / etch stop layer) / Mo-Si multilayer (reflective layer) / Si (substrate). Since the Ru etch stop layer should not be etched, infinitely high selectivity of SnO2 layer to Ru ESL is required. To obtain infinitely high etch selectivity and very low LER (line edge roughness) values, etch parameters of gas flow ratio, top electrode power, dc self - bias voltage (Vdc), and etch time were varied in inductively coupled Cl2/Ar plasmas. For certain process window, infinitely high etch selectivity of SnO2 to Ru ESL could be obtained by optimizing the process parameters. Etch characteristics were measured by on scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) analyses. Detailed mechanisms for ultra-high etch selectivity will be discussed.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.332-332
• /
• 2011

The extreme ultraviolet (EUV) radiation, whose wavelength is from 120 nm down to 10 nm, and the energy from 10 eV up to 124 eV, is widely utilized such as in photoelectron spectroscopy, solar imaging, especially in lithography and soft x-ray microscopy. In this study, we have investigated the plasma diagnostics as well as the debris characteristics between the two types of dense plasma focusing devices with coaxial electrodes of Mather and hypocycloidal pinch (HCP), respectively. The EUV emission intensity, electron temperature and plasma density have been investigated in these cylindrical focused plasma along with the debris characteristics. An input voltage of 5 kV has been applied to the capacitor bank of 1.53 uF and the diode chamber has been filled with Ar gas at pressure ranged from 1 mTorr and 180 mTorr. The inner surface of the cathode was covered by polyacetal insulator. The central anode electrode has been made of tin. The wavelength of the EUV emission has been measured to be in the range of 6~16 nm by a photo-detector (AXUV-100 Zr/C, IRD). The visible emission has also been measured by the spectrometer with the wavelength range of 200~1,100 nm. The electron temperature and plasma density have been measured by the Boltzmann plot and Stark broadening methods, respectively, under the assumption of local thermodynamic equilibrium (LTE).

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.480-480
• /
• 2011

양극산화(anodization)는 금속을 전기화학적으로 산화시켜 금속산화물로 만드는 기술로서 최근 다양한 크기의 나노 구조를 제조하는 기술로 각광받고 있으며, 이러한 기술에 의하여 얻어지는 anodic aluminum oxide(AAO)는 magnetic data storage, optoelectronic device, sensor에 적용될 수 있는 nano device 뿐만 아니라 nanostructure를 제조하기 위한 template 및 mask로써 최근 광범위 하게 연구되고 있다. 또한, AAO는 Al2O3의 단단한 구조를 가진 무기재료이므로 solid mask로써 다른 porous materials 보다 뛰어난 특성을 갖고 있다. 또한 electron-beam lithography 및 block co-polymer 에 의한 patterning 과 비교하여 매우 경제적이며, 재현성이 우수할 뿐만 아니라 대면적에서 나노 구조의 크기 및 형상제어가 비교적 쉽기 때문에 널리 사용되고 있다. 그러나, AAO 형성 시 생기게 되는 반구형 모양의 barrier layer는 물질(substance)과 기판과의 direct physical and electrical contact을 방해하기 때문에 해결해야 할 가장 큰 문제점 중 하나로 알려져 있다. 따라서 본 연구에서는 실리콘 기판위의 형성된 AAO의 barrier layer를 Cl/BCl3 gas mixture에서 Neutral Beam Etching (NBE)과 Ion Beam Etching (IBE) 로 각각 식각한 후 그 결과와 비교하였다. NBE와 IBE 모두 Cl2/BCl3 gas mixture에서 BCl3 gas의 첨가량이 60% 일 경우 etch rate이 가장 높게 나타났고, optical emission spectroscopy (OES)로 Cl2/BCl3 플라즈마 내의 Cl radical density와 X-ray photoelectron spectroscopy (XPS)로 AAO 표면 위를 관찰한 결과 휘발성 BOxCly의 형성이 AAO 식각에 크게 관여함을 확인 할 수 있었다. 또한, NBE와 IBE 실험한 다양한 Cl2/BCl3 gas mixture ratio 에서 AAO가 식각이 되지만, 이온빔의 경우 나노사이즈의 AAO pore의 charging에 의해 pore 아래쪽의 위치한 barrier layer를 어떤 식각조건에서도 제거하지 못하였다. 하지만, NBE에서는 BCl3-rich Cl2/BCl3 gas mixture인 식각조건에서 AAO pore에 휘발성 BOxCly를 형성하면서 barrier layer를 제거할 수 있었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.252.2-252.2
• /
• 2013

ZnO nanostructures have a lot of interest for decades due to its varied applications such as light-emitting devices, power generators, solar cells, and sensing devices etc. To get the high performance of these devices, the factors of nanostructure geometry, spacing, and alignment are important. So, Patterning of vertically- aligned ZnO nanowires are currently attractive. However, many of ZnO nanowire or nanorod fabrication methods are needs high temperature, such vapor phase transport process, metal-organic chemical vapor deposition (MOCVD), metal-organic vapor phase epitaxy, thermal evaporation, pulse laser deposition and thermal chemical vapor deposition. While hydrothermal process has great advantages-low temperature (less than $100^{\circ}C$), simple steps, short time consuming, without catalyst, and relatively ease to control than as mentioned various methods. In this work, we investigate the dependence of ZnO nanowire alignment and morphology on si substrate using of nanosphere template with various precursor concentration and components via hydrothermal process. The brief experimental scheme is as follow. First synthesized ZnO seed solution was spun coated on to cleaned Si substrate, and then annealed $350^{\circ}C$ for 1h in the furnace. Second, 200nm sized close-packed nanospheres were formed on the seed layer-coated substrate by using of gas-liquid-solid interfacial self-assembly method and drying in vaccum desicator for about a day to enhance the adhesion between seed layer and nanospheres. After that, zinc oxide nanowires were synthesized using a low temperature hydrothermal method based on alkali solution. The specimens were immersed upside down in the autoclave bath to prevent some precipitates which formed and covered on the surface. The hydrothermal conditions such as growth temperature, growth time, solution concentration, and additives are variously performed to optimize the morphologies of nanowire. To characterize the crystal structure of seed layer and nanowires, morphology, and optical properties, X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), Raman spectroscopy, and photoluminescence (PL) studies were investigated.

• Korean Chemical Engineering Research
• /
• 제50권5호
• /
• pp.929-932
• /
• 2012

화면표시장치 제조에 널리 이용되고 있는 미세구조 제조향 노광공정을 대신할 기반기술을 개발하고자 한다. 저가의 Polycarbonate 기판에 미세구조를 제조하기 위하여, Spin Coating으로 Polystyrene 박막을 형성하고 박막 위에 Polydimethylsiloxane 주형으로 소프트석판술을 적용하였다. 제조된 구조에 나노입자들을 배열하기 위해 계면작용을 이용하고자 하므로, 구조의 표면을 화학반응에 의해 소수성으로 개질하였다. 소수성으로의 개질은 Polystyrene 표면을 과망간칼륨으로 처리하고 Aminopropyltriethoxysilane을 반응시켜서 수행되었다. 개질된 특성은 X선광전자분광기로 분석되었다. 개질된 표면에서 친수성나노입자들이 분산되어 있는 수용액을 마이크로리터 단위의 방울로 떨어뜨리고, 수용액을 증발시킨다. 증발과정에서 계면상호작용과 미세구조의 물리적 유도로 특정 영역에 나노입자들이 배열되었다. 그리고, 이 배열의 전기적 응용을 확인하였다.