• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.12
• /
• pp.1308-1315
• /
• 2009

A full-polarimetric scatterometer(HPS: Hongik Polarimetric Scatterometer) for X-band is designed, fabricated, and verified using the theoretically well-known point-targets in this paper. The X-band full-polarimetric scatterometer consists of an OMT(Orthogonal-Mode Transducer)+horn antenna, the angle control part for the OMT+horn antenna, a transmitter/receiver with a network analyzer and a frequency-conversion circuitry, and a movable support of these parts. We use an inclinometer sensor to control the vertical and horizontal incidence angles. The full polarimetric data can be obtained because of the polarization switches and the OMT. The accuracy of the scatterometer system is verified by measuring the polarimetric RCS(Radar Cross Section) of one of the theoretically well-known point-targets, i.e., a corner reflector.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.11
• /
• pp.1311-1316
• /
• 2014

To be used in a transmitter of a satellite transponder of this paper, X band 25W power amplifier module, a part constituting of high-power amplifier is transmitted to the equipment for transmitting to geostationary communications satellites(36,000Km distance). PAM consisted a total of four power amplifier module has a high output characteristic of the high-output amplifier is used in the ground station. Used in conjunction with the structured type power amplifier module is composed of Serial Combining Structure. This PAM(Power Amplifier Module) configured by combining the circuit with the power amplifier, 10 MMIC chips and the Al2O3 thin film substrate using a Hybrid Technique of power amplifier module, was implemented at X band PAM(Power Amplifier Module) of 25W grade.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.7
• /
• pp.1210-1218
• /
• 2001

In this paper, A X-band voltage-controlled hair-pin resonator oscillator(VCHRO) is able to a local oscillator or a signal source in transmitter/receiver of a microwave communication system for mobile radar, is designed and fabricated In order to apply mobile radar system is used the hair-pin resonator stronger on shock or vibration than the dielectric resonator, and also, in order to improvement the phase noise and output power is used a system of serial feedback format A hair-pin resonator was simulated by momentum method of HP ADS and then a oscillator circuit was designed that operates at 10.525 GHz by nonlinear method in harmonic balance simulation. The HRO generated output power of 6.93 dBm at 10.525 GHz, phase noise of -57.74 dBc at 100 kHz offset from carrier and the 2'nd harmonic was suppressed -23.90 dBc.

• Proceedings of the IEEK Conference
• /
• 2003.07b
• /
• pp.1125-1128
• /
• 2003

This paper presents the design method of a Colpitts type oscillator with coplanar waveguide(CPW) structures in the range of Ka-band frequency for transmitter and receiver modules. Series short stubs of CPW patterns provide inductances and capacitances in the range of Ka-band which can be expressed as a CLC-$\pi$ equivalent circuit. The experimentation has employed ro4003 substrates as a CPW substrate which has a dielectric constant of 3.38 and a signal and ground space of 100um. A method of momentum simulation for the CPW patterns has performed with an ADS software tool of Hewlett-Packard Corp. Inductance and capacitance circuits of a Colpitts oscillator was interconnected to a MESFET with CPW bend structures of including the input and output impedance matching circuits of the active transistor. Circuit parameters for impedance matching were determined through the network conversion to the equivalent length of CPW transmission lines by using T-network 1 $\pi$-network conversion circuit. A Colpitts oscillator was fabricated on the substrate of a area of 8.5mm x 17.4mm with a MESFET of Fujitsu FMM5704X and CPW series short stubs. The design suggested the possibility of realizing oscillators on a planar surface for the wireless system of tansmitter and receiver modules in the frequency range of 30GHz

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.2
• /
• pp.97-104
• /
• 2017

In this paper, we designed and fabricated the multi band Transceiver Assembly(TCA) for the Multi Channel Synthetic Aperture Radar(MCSAR) containing C-band, X-band, Ku-band and we researched to verify electrical performance of TCA. The transceiver consists of transmitters, receivers, signal selection modules for each band, and stability oscillator, frequency synthesizer, controller, power distributor. The transceiver has a receive path selection and bandwidth selection functions in accordance with the operating mode. And the transceiver can transmit and receive all three bands simultaneously, each band has a bandwidth of up to 300 MHz. Final transmission output of transceiver for each band is over 20 dBm to be suitable for driving the T/R module. Receiver bandwidth is selected according to the required function and receiver gain has approximately C-band 52 dB, X-band 50 dB, Ku-band 60 dB, the maximum noise figure of Ku-band V polarization is 4.28 dB in the whole band H, V polarization. As a result of the electrical performance test, a multi-band TCA is satisfied the property requirements of the MCSAR.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.5
• /
• pp.486-489
• /
• 2016

A horn antenna with corrugation structure and a PTFE(Polytetrafluoroethylene) teflon(relative permittivity=2.1) dielectric lens for good impedance matching characteristic and high gain performance is proposed in this paper. The proposed antenna shows measured return loss below -25 dB over the operating X band(8~12 GHz), the peak gain of 22.3 dBi at the center frequency(10 GHz) and has overall size of $110mm{\times}110mm{\times}135mm$. Considering the performance of the proposed antenna, it is suitable for being inserted in a radar level transmitters, particularly for gas tanks on vessels or off-shore plants containing gas with very low reflectivity and relative permittivity such as LNG or LPG.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.16 no.5
• /
• pp.152-161
• /
• 2017

The CBTC(Communication based Train Control) system employed on 2.4GHz ISM band adopt the IEEE802.11.x standard. Therefor communication time delay, distortion and data losses will be produced. To overcome these problems, CPSK(Continuous Phase shift keying) modulated DS/SS(Direct Sequence Spread Spectrum) transmitter with 908MHz carrier frequency is proposed. Through the eye diagram and scatter diagram the performance is analysed. And the phase noise characteristic of the local oscillator is measured about 60dBc/Hz, this means that the phase noise performance is very good compared to the signal. Reference frequency suppression of the 2nd local oscillator is 50dB below compared to the signal. Through the polarities of the complementary signal equally probable, the line spectrum of the output spectrum is eliminated. The nonlinear effects which introduce the spectral spreading or spectral regeneration is reduced remarkably.

• Journal of Korea Society of Industrial Information Systems
• /
• v.23 no.4
• /
• pp.23-31
• /
• 2018

This paper presented the implementation and design of the 2T-2R wireless HD video streaming systems over 1.7 GHz frequency band using 3GPP LTE-TDD standard on NI USRP RIO SDR platform. The baseband of the system used USRP RIO that are stored in Xilinx Kintex-7 chip to implement LTE-TDD transceiver modem, the signal that are transmitted from USRP RIO up or down converts to 1.7 GHz by using self-designed 1.7 GHz RF transceiver modules and it is finally communicated HD video data through self-designed 2x9 sub array antennas. It is that communication method between USRP RIO and Host PC use PCI express x4 to minimize delay of data to transmit and receive. The implemented system show high error vector magnitude performance above 32 dBc and to transmit and receive HD video in experiment environment anywhere. The proposed hybrid beam forming system could be used not only in the future 5G mobile communication systems under 6 GHz frequency band but also in the systems over 6 GHz frequency band like ones in mmWave frequency bands.

• Journal of the Korea Society of Computer and Information
• /
• v.5 no.2
• /
• pp.105-114
• /
• 2000

In this Paper in order to break with real-time position of signal source which have first dimension motion, the N antenna is arrayed with half-circle, the incident angle of signal source from receiving power pattern to receive at receive antenna is estimated and measured, and the system that measure horizontal moving distance of signal source is designed. Signal source is constructed by 10-20dBm transmitter power which frequency is 10.52GHz of X band, and on horizontally moving the position of signal source. validity of new method is confirmed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.8 s.111
• /
• pp.773-787
• /
• 2006

An airborne radar is an essential aviation electronic system for the aircraft to perform various civil and/or military missions in all weather environments. This paper presents the design, development, and test results of the multi-mode X-band pulsed Doppler radar system test model for helicopter-borne flight test. This radar system consists of 4 LRUs(Line-Replacement Unit), which include antenna unit, transmitter and receiver unit, radar signal & data processing unit and display Unit. The developed core technologies include the planar array antenna, TWTA transmitter, coherent I/Q detector, digital pulse compression, MTI, DSP based Doppler FFT filter, adaptive CFAR, moving clutter compensation, platform motion stabilizer, and tracking capability. The design performance of the developed radar system is verified through various ground fixed and moving vehicle test as well as helicopter-borne field tests including MTD(Moving Target Detector) capability for the Doppler compensation due to the moving platform motion.