• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.2
• /
• pp.172-182
• /
• 2014

In this paper, is is presented the result of design and fabrication for X band T/R module using in active array radar. The high power RF circuit was fabricated using GaN element, so that high power and high efficiency was fulfilled comparing with the previous T/R module that have under 50 W output power for X band. Designed X band T/R module demonstrated 200 W(53 dBm) peak power, 20 us pulse width with 0.4 dB pulse droop and 20 % duty cycle. And it has characteristics of 26 dB receive gain and 4.5 dB noise figure. The structure was applied to prevent serious damage of receive path and GaN HPA by transmitting power during trasmit time of a pulse radar.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.11
• /
• pp.1311-1316
• /
• 2014

To be used in a transmitter of a satellite transponder of this paper, X band 25W power amplifier module, a part constituting of high-power amplifier is transmitted to the equipment for transmitting to geostationary communications satellites(36,000Km distance). PAM consisted a total of four power amplifier module has a high output characteristic of the high-output amplifier is used in the ground station. Used in conjunction with the structured type power amplifier module is composed of Serial Combining Structure. This PAM(Power Amplifier Module) configured by combining the circuit with the power amplifier, 10 MMIC chips and the Al2O3 thin film substrate using a Hybrid Technique of power amplifier module, was implemented at X band PAM(Power Amplifier Module) of 25W grade.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.6 no.1 s.12
• /
• pp.38-46
• /
• 2007

In this paper an X-band low phase noise HBT oscillator using a planar type MMIC resonator is designed. The chip area of the proposed resonator shows a quarter of the conventional hair-pin resonator using distributed transmission lines. The measurement results show oscillation frequency of 8.295 GHz, the power output of 4.8 dBm, and phase noise characteristic of -106.8 dBc/Hz and -121.7 dBc/Hz at 100 kHz and 1 MHz offset frequencies respectively.

• Journal of Satellite, Information and Communications
• /
• v.10 no.3
• /
• pp.131-136
• /
• 2015

In this paper, prior to the flight model X-band dual-mode circular cavity filter required for the high power transmission of the observation payload in the geostationary satellite, the development model are designed and analyzed to show the analytical multipactor requirement margin. First of all, the multipaction breakdown power sensitivities were analyzed by changing the iris width and thickness within the filter, and through that the iris width and thickness was selected and then the multipaction threshold powers over the frequencies within the bandwidth were analyzed and the required margin of 8 dB was obtained. Also for the high power transmission filter, another important phenomena known as corona breakdown are analyzed for the iris width and thickness changes. Finally the development model manufactured was tested and the results met the key requirements.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.32 no.3
• /
• pp.141-147
• /
• 2019

In this paper, a systematic beam splitter design for multi-beam forming is proposed. The objective of this research is to a design beam splitter that splits and focuses scattering microwaves into intense beams in multiple directions. It is difficult to split multi-beam to non-specific directions with theoretical approaches. Therefore, instead of using transformation optics(TO), which is a widely used process for controlling electromagnetic wave propagation, we used a systematic design process called the phase field design method to obtain an optimal topological structure of beam splitter. The objective function is to maximize the norm of electric field of the target areas of each direction. To avoid island structure and obtain the structure in one body, volume constraint is added to the optimization problem by using augmented Lagrangian. Target frequency is set to X-band 10GHz. The optimal beam splitter performed well in multi-beam forming and the transported electric energy of target areas improved. A frequency dependency test was conducted in the X-band to determine effective frequency range.

• Journal of Advanced Navigation Technology
• /
• v.22 no.1
• /
• pp.31-36
• /
• 2018

In this paper, we designed and implemented an ultra wideband(UWB) antenna with band rejection characteristics. The proposed antenna consists of a planar radiation patch with slots and ground planes on both sides. Due to the slots in the radiation patch, the antenna shows band rejection characteristics. U-type slot contributes for wireless local area network(WLAN, 5.15~5.825 GHz) band rejection and n-type slot contributes for X-Band(7.25~8.395 GHz) band rejection. To make voltage standing wave ratio(VSWR) less than 2.0 for UWB frequency band except rejection bands, the shapes of planar radiation patch and ground plane was modified. The Ansoft 's high frequency structure simulator(HFSS) was used for the design process and simulations of the proposed antenna. The simulated antenna showed VSWR less than 2.0 for all UWB band excepts for dual rejection bands of 5.15 ~ 5.94 GHz and 7.02 ~ 8.45 GHz. And measured VSWR for the implemented antenna is less than 2.0 for all UWB band of 3.10~10.60 GHz excluding dual rejection bands of 5.12~5.95 GHz and 7.20~8.58 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.1
• /
• pp.1-9
• /
• 2017

In this paper, ETRI's $0.25{\mu}m$ GaN MMIC process is introduced and the fabricated results of X-Band 3 W power amplifier MMIC are discussed. The one-stage X-Band 3 W power amplifier MMIC using the $0.25{\mu}m$ GaN MMIC devices has been designed and fabricated. From the fabricated GaN MMIC, the characteristics of the $0.25{\mu}m$ GaN MMIC process and devices are evaluated and analyzed. The X-band power amplifier MMIC shows output power of 3.5 W, gain of 10 dB, and power-added efficiency of 35 %.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.11
• /
• pp.1663-1668
• /
• 1993

An X-band contiguous band diplexer is realized by using asymmetrical coupled microstrip lines. The design is based on the singly terminated low pass prototype filter and optimized by using SuperCompack. The designed channel 1 and channel 2 bandwidth is 22%, and 18% respectively, where the center frequency is 9,11 GHz. The measured results of the fabricated diplexer are in good agreement with the designed ones, but the measured insertion loss is slightly highier(0.5dB) than those of the designed value.

• Journal of IKEEE
• /
• v.22 no.2
• /
• pp.413-419
• /
• 2018

An UWB(Ultra Wide Band) antenna with band rejection characteristics is designed and implemented. A planar radiation patch with slot, parasitic elements on both sides of strip and ground plane on back side consist the proposed antenna. The slot in the radiation patch and parasitic elements contribute corresponding bands rejection characteristics. The slot contributes for WiMAX(World interoperability for Microwave Access, 3.30~3.70 GHz) band rejection and parasitic elements contribute for X-Band(7.25~8.395 GHz) rejection. Ansoft's HFSS(High Frequency Structure Simulator) was used to design the proposed antenna and performance simulations. Simulation result showed VSWR(Voltage Standing Wave Ratio) less than 2.0 for UWB band except for dual rejection bands of 3.30~3.86 GHz and 7.21~8.39 GHz. And VSWR measurement result for the implemented antenna shows less than 2.0 for 3.10~10.60 GHz band except dual rejection bands of 3.25~3.71 GHz and 7.25~8.46 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.1
• /
• pp.80-83
• /
• 2017

In this paper, the X-band reconfigurable frequency selective surface having flexible geometry was proposed. The proposed RFSS is composed of patterns of cross-shaped loop with inductive stub, which can control the frequency response for C-Band and X-band by ON/OFF state of PIN diode. To minimize the parasitic effect and to obtain the high level of isolation between the unit cell of FSS and the bias circuit, we designed the grid type bias line on bottom layer through via hole. The measured transmission characteristics show good agreement with the simulation results and good stability of frequency response for different incident angles and curvatures of surface.