• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.7A
• /
• pp.935-942
• /
• 2000

In this paper, miniature voltage-controlled oscillator(VCO) for 1.6GHz PCS band is designed and implemented. Colpitts type LC resonating oscillator is designed with multilayer PCB and circuit parameters are optimized using the circuit simulator. Using the optimized design parameters, miniature VCO with 6X6X1.8mm3 (0.065cc)dimensions is fabricated and experimented. Developed VCO has -1.67dBm $\pm$0.5dBm output power level in52.5MHz tunung range, and has -99.33dBc/Hz phase noise performance at 10 KHz frequency offset.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.3
• /
• pp.49-57
• /
• 2000

In this paper, lumped-element isolator is analyzed and designed using the scattering matrix approach. Using the designed parameters, compact isolator with 7.0x7.0x2.3 mm$^3$ dimensions is fabricated and tested in 1.765GHz PCS phone band. Implemented isolator shows 29.95dB isolation characteristic at center frequency and has 0.35dB insertion loss in overall 30MHz operating bandwidth. Return losses of input and output port are measured below -19 dB. Experimental results show that the implemented isolator has better performances than the conventional one.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.1
• /
• pp.87-97
• /
• 1998

This paper describes an analysis of tunable characteristic for magnetically tunable E-plane type finline filter on a ferrite substrate. The proposed design is based on using of quarter wavelength transmission line for compensating the negative length transmission line of end K-inverters of E-plane type waveguide filters and the tunable characteristics of designed filters are analyzed. The analysis results of filter and inverter structure loaded with finline on a ferrite substrate are obtained using the edge based finite element method including higher order mode effects. The X-band experimental results for bilateral and unilateral finline magnetically tunable E-plane type waveguide filters agree well with the simulated data.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.3
• /
• pp.223-228
• /
• 2010

In this paper, temperature compensation circuit for the X-band voltage controlled oscillator(VCO) is presented by using the temperature sensor with the OP-AMP circuit. The frequency drifting by the temperature could be compensated by applying the tuning voltage which include the linearly changing output voltage of the temperature sensor. As a result, the frequency variation is reduced to 6.6~4.4 MHzfrom the 71~73 MHz variation with the compensation circuit over -30~+$60^{\circ}C$ range, when VCO is operated in the frequency range of 9.95~10.05 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.7
• /
• pp.823-830
• /
• 2010

This paper deals with a coaxial-to-waveguide transition generating circularly polarized wave to be connected with horn antennas. By combining vertical coaxial fed structure, back-short and the polarization twisting structure, the circular polarization is successfully generated in the waveguide. The designed and implemented transition shows that the present structure can significantly reduce the size of the antenna part at X-band.

• Geophysics and Geophysical Exploration
• /
• v.15 no.1
• /
• pp.16-22
• /
• 2012

In this study, we setup a ground-based scatterometer using an antenna of which the center frequency is 9.5 GHz (X-band), and measured radar backscatterings from air/ice and ice/water interfaces to extract ice thickness. Both of air/ice and ice/water interfaces make strong radar backscatterings and so we can clearly identify two peaks in measured data by scatterometer. By using the distance of two peaks and refractive index of ice, we confirmed that it is possible to measure ice thickness. Field survey was performed at the downstream of Jiam River flowing into Chuncheon Lake. We measured radar backscattering from river ice along a survey path and extracted ice thickness. The ice thickness map of the downstream of Jiam River was produced by using kriging which is one of well known interpolation methods. The ice thickness was about 50 cm along the mainstream while ice was thin as 30 ~ 40 cm at a fast-flowing meander. Ice thickness was particularly thinner at some locations than that of surrounding areas even in the mainstream region of constant flow. This was because of impurities in ice or artificially formed refrozen holes after fishing. We expect that this study helps to expand utilization field of X-band SAR and airborne scatterometer system.

• Journal of Aerospace System Engineering
• /
• v.17 no.1
• /
• pp.42-50
• /
• 2023

In this study, hexagonal ferrite powder with chemical formula SrZn_2-xCo_xFe₁₆O₂₇ was synthesized by a solid-state reaction method and its electromagnetic (EM) wave absorption characteristics were evaluated in the frequency range of 0.1-18 GHz with absorber thickness range of 0 - 10 mm. Reflection loss (RL) affecting electromagnetic wave absorption performance was calculated based on the transmission line theory using measured complex permeabilities and permittivities. RL spectra were also directly measured for some samples. They were well matched with calculated results. High-frequency complex permeability characteristics were changed gradually according to the amount of Co substitution (x). The EM wave absorption frequency band could be tuned accordingly. Hexaferrite samples with x = 1.0, 1.25, and 1.5 exhibited remarkable maximum electromagnetic wave absorption performances with minimum RL (RL_min) lowered than -50 dB. They also showed a very broad frequency band (Δf > 10 GHz) in which more than 90% of the EM wave energy absorption occurred (RL ≤ -10 dB).

• Journal of the Korean Society of Radiology
• /
• v.7 no.6
• /
• pp.403-408
• /
• 2013

This study made a tentative estimation of the shielding rate of barium compound by thickness through monte carlo simulation to apply medical radiation shielding products that can replace existing lead. Barium sulfate($BaSO_4$) was used for the shielding material, and thickness of the shielding material specimen was simulated from 0.1 mm to 5 mm by applying $15{\times}15cm^2$ of specimen area, $4.5g/cm^3$ of density of barium sulfate, and $11.34g/cm^3$ density of lead. Entered source was simulated with 10kVp Step in consecutive X-ray energy spectrum(40 kVp ~ 120 kVp). Absorption probability in 40 kVp ~ 60 kVp showed same shielding rate with lead in 3 mm ~ 5 mm of thickness, but it was identified that under 2 mm, the shielding rate was a bit lower than the existing lead shielding material. Also, the shielding rate in 70 kVp ~ 120 kVp energy band showed similar performance as the existing lead shielding material, but it was tentatively estimated as fairly low shielding rate below 0.5 mm. This study estimated the shielding rate of barium compound as the thickness function of x-ray energy band for medical radiation through monte carlo simulation, and made comparative analysis with existing lead. Also, this study intended to verify application validity of the x-ray shielding material for medical radiation of pure barium sulfate. As a result, it was estimated that the shielding effect was 95% higher than the existing lead 1.5 mm in at least 2 mm thickness of barium compound in medical radiation energy band 70 kVp ~ 120 kVp, and this result is considered valid to be provided as a base data in weight lightening production of radiation shielding product for medical radiation.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.9 no.4
• /
• pp.359-365
• /
• 2016

In this paper, a novel coupled C type resonator is proposed for improvement of phase noise characteristics that is weak point of oscillator using planar type microstrip line resonator. Oscillator using proposed coupled C type resonator is designed, it has improved phase noise characteristics. At the fundamental frequency of 9.8GHz, 2.4dBm output power and -82.7 dBc@100kHz phase noise have been measured for oscillator with coupled C type resonator. The phase noise characteristics of oscillator is improved about 9.7dB compared to one using the general ${\lambda}/4$ microstrip resonator. Due to its simple fabrication process and planar type, it is expected that the technique in this paper can be widely used for low phase noise oscillators for both MIC and MMIC applications.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.3 no.1
• /
• pp.20-27
• /
• 1992

A synthesized isotropic pattern antenna can be realized by arrangeing $\lambda$/ 2 dipole along each x, y, z axis. The sleeve type $\lambda$/ 2 dipole antenna is used as a basic element for a proper impedance matching at feeding point and minimum mutual coupling effect between each element at 820 MHz - 895 MHz band. The total electric field intensity radiated from the designed isotropic pattern antenna is drived from the magnetic vector potential which is produced by each sleeve $\lambda$/ 2 dipole in the far field. This total electric field intensity is inversely proportional only to distance $\gamma$from the origin of coordinates, and pattern factor variation is less than 2.1dB. The measured value of total electric field variation depending on pattern factor is less then 2.8dB, and the difference between the calculated and measured value is 0.7dB.