• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.3
• /
• pp.352-357
• /
• 2016

More recently, workers and passengers of casualties has increased by rear-end collisions of unexpected while working on the road. Recently attracted air chamber TMA mounting car accidents which occurred in 3 years, and analyzed the effect of reducing the shock absorption and protection performance and casualties. There is a risk of the vehicle AIS4 more injury of high five accidents of casualties risk, also, was the analysis that there is risk of death was avoided by the air chamber TMA and SGT. Therefore, by mounting the TMA in the rear-end accident, so you can reduce the death and casualties, it must be increased this of attach rate for road construction vehicle.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.51 no.5
• /
• pp.1-12
• /
• 2023

This study evaluated the overturning stability of portable tripod ladders used for high-altitude work such as tree management and pruning work in landscaping construction and management. Portable tripod ladders, which are included in general mobile or portable ladders frequently used in industrial sites, are supported in a triangular support structure, not a 4-point support like common A-type Ladders. In addition, since the working height is more than twice that of a mobile or portable ladder, the possibility of an overturning accident that threatens the safety of workers with a fall accident is high. Therefore, based on the overturning stability test specified in ANSI-ASC A14.7 and EN 131-Part 7, which are related standards for about 130 types of portable tripod ladders sold and used in Korea. An equation to calculate each moment according to working height was derived. Then, each calculated moment was compared to evaluate the safety factor for overturning and stability. As a result of the overturning stability evaluation according to each standard, when the provisions of EN 131-Part 7 were applied, portable tripod ladders with 8 steps in the rear direction and 6 steps or more in the side direction were evaluated as unstable against overturning, but according to ANSI-ASC A14.7 regulations. It was evaluated that the stability against overturning was secured in all directions and number of steps.

• Journal of the Korean Society of Safety
• /
• v.28 no.6
• /
• pp.42-48
• /
• 2013

Forensic engineering is the application of engineering principles covering the investigation of constructed facilities and systems that fail to perform as intended, causing personal injury or damage to property, environmental, economy etc. In the year 2012, two collapsed accidents of the large scaffolding system in national thermal power station occurred one after another, causing many casualties. In this study, we had performed to investigate the collapsed accident of scaffolding system occurred in the a thermal power station of two accidents. First, the investigation about the collapsed accidents site had performed to understand collapsed state and structures of the scaffolding system. Second, reviewing the materials concerning about the applied weight on the scaffolding system had performed. The applied weight is sum of the weights of the 15 workers, additional materials for coating work and dispersed and loaded shot ball on the foothold etc. the applied weight that calculated exceed more three times than the safe working load. Third, we had confirmed the install state of the materials of the scaffolding system by reviewing the quantity of the materials on the manual and the real system. Last, structural analysis had performed to evaluate structural integrity of the scaffolding system using Ansys. Through a series of this processes, the definite accidents causes of the collapsed scaffolding system revealed. Through these studies, the collapse accident that may occur in the scaffolding system in thermal power station can be minimized by performing specialized and systematic investigation on the accidents in terms of Forensic engineering.

• Research in Community and Public Health Nursing
• /
• v.15 no.1
• /
• pp.84-94
• /
• 2004

Purpose: The purpose of this study was to examine the health care management status of preschoolers depending on the children's characteristics. Methods: The sample of this study were 212 mothers of preschoolers attending Child Care Centers in three cities, Seoul, Daejon, and Suwon, in Korea. A self administered questionnaire developed by investigators was used to collect data from September 15 to October 31, 2002. Data was analyzed with SPSS 11.5 Win program. Results: 5.7% of the children had not completed their vaccination programs. Children who were second or later birth order showed less complete vaccination rates than firstborn babies. Children who had working mothers showed less complete vaccination rates than those whose mothers did not work. Among the various vaccinations, the DPT and MMR booster vaccination rates were the lowest. Home safety scores were higher when mothers have younger children. higher monthly incomes and reside in apartment type houses. Forty one(41%) of the preschoolers experienced accidents, and the accident rate was higher in boys and children with easy temperament. The most frequently experienced accident was laceration. Twenty eight point eight percent(28.8%) of the children experienced hospitalization because of various diseases. Most of the mothers perceived their children healthy. However, children who were second or third born were perceived less as healthy. Children in families with less monthly income were perceived as less healthy. Conclusions: This study provided basic data about preschoolers' health care management status focusing on vaccinations and accident rates. More attention should be paid to preschoolers' health and safety. Related factors found in this study should be considered when providing anticipatory guidance for parents.

• Journal of Ship and Ocean Technology
• /
• v.5 no.3
• /
• pp.1-13
• /
• 2001

Present-day rules and regulations for the design and construction of ships are almost without exemption of a prescriptive and deterministic nature. Often it is argued that this situation is far from ideal; it does no right to the advances, which have been made during the past decades in engineering tools in marine technology, both in methodology and in computational power. Within IMO this has been realized for some time and has resulted in proposals to use Formal Safety Assessment(FSA) as a tool to improve and to modernize the rule making process. The present paper makes use of elements of the FSA methodology, but instead of working towards generic regulations or requirements, a Risk Assessment Approach, not unlike a 'safety case'; valid for a certain ship or type of ship is worked out. Delft University of Technology investigated the application of safely assessment procedures in ship design, in co-operation with Anthony Veder Shipowners and safety experts from Safely Service Center BV. The ship considered is a semi-pressurized-fully refrigerated LPG carrier. On the basis of the assumption that a major accident occurs, various accident, scenarios were considered and assessed, which would impair the safety of the carrier. In a so-called Risk Matrix, in which accident frequencies versus the consequence of the scenarios are depicted, the calculated risks all appeared lo be in the ALARP('as low as reasonable practicable') region. A number of design alternatives were compared, both on safety merits and cost-effectiveness. The experience gained with this scenario-based approach will be used to establish a set of general requirements for safety assessment techniques in ship design. In the view that assessment results will be most probably presented in a quasi-quantified manner, the requirements are concerned with uniformity of both the safety assessment. These requirements make it possible that valid comparison between various assessment studies can be made. Safety assessment, founded on these requirements, provides a validated and helpful source of data during the coming years, and provides naval architects and engineers with tools experience and data for safety assessment procedures in ship design. However a lot of effort has to be spent in order to make the methods applicable in day-to-day practice.

• Journal of the Korean Society of Safety
• /
• v.31 no.2
• /
• pp.112-118
• /
• 2016

The labor force has moved to services industry. An industrial accidents of service industry is three people on 10 persons in 2013. This research conducted questionnaire surveys of 1:1 directly person interviews with a structured questionnaire intended for 150 service workplaces, in order to improve occupational safety and health in very small service workplace with less than 5 employee. The survey contents is employment type, safety and health management system, safety and health training, activities. In the results, working with non-regular(informal) workers is two people on 10 persons 27.1% and female workers is about five people on 10 persons with 58.1%, and that 67.9% of non-regular workers who are mainly engaged in the production line appeared. And the work-related injury and accident experience was 3.3% and the occupational injury rate was 1.02%, especially occupational injury rate of female workers was 0.88%. Workplace risk assessment carried out in response that it was very low as 10.0% of the total. Also the safety & health education and activities was very low. Thus the safety consciousness and education is urgently required in order to prevent the industrial accidents.

• Journal of the Korea Safety Management & Science
• /
• v.13 no.4
• /
• pp.61-69
• /
• 2011

The hazard conditions on plant works of the steel industry have been investigated to efficiently prevent from industrial accidents. The plant works are eventually carried out by workers of smaller service companies where the safety management systems are not well established, on behalf of the main steel company. Based on the preliminary risk assessment on the plant working and open literature reviews, the safety management systems, which can be applied to the plant workplace of each process, are studied and then the step-by-step 4M check-list method is established. Accordingly, the risk assessment technique using 4M checklist for the plant workplace is proposed. In addition, a standardized flow-chart for safety management of plant work is introduced. These risk assessment technique and flow-chart can definitely contribute to the reduction of industrial accidents, considering the risk characterization and the unsafe conditions in small and medium-sized plant workplace, as effective safety management tools and safety guide line.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.11a
• /
• pp.63-64
• /
• 2020

The purpose of this study is to find out how construction sites workers experience adaptation processes in relation to the prevention of safety accidents in the workplace through the method of grounded theory. In order to understand the experience of preventing safety accidents of workers at construction sites, a grounded theory analysis method was chosen. In order to achieve the purpose of this study, the first questionnaire was sent to 17 people working in the construction site by e-mail, and the participants of the study were met one by one for in-depth interviews. As a result of this study, the paradigm model of the experience of preventing safety accidents of workers at construction sites was classified into causal conditions, contextual conditions, central phenomena, intervening conditions, action/interactions, and outcomes. The conclusions of this study are as follows. First, forming a safety culture that can improve the safety awareness of construction sites is a priority. Second, it is necessary to improve self-management capabilities so that construction workers can accurately diagnose their current state such as their own body, emotion, and cognition and provide appropriate safety education. Third, providing safety education for construction workers with negative thoughts or distorted beliefs about safety accidents needs to include psychological treatment and counseling, such as methods of emotional purification, methods of relieving and managing stress, and methods of removing trauma.

• Journal of the Korean Society of Safety
• /
• v.39 no.2
• /
• pp.44-53
• /
• 2024

In addition to being used for ascending and descending to work locations, portable ladders are widely used as a substitute for work platforms when working at heights in homes and industrial sites. However, accidents continue to occur in industrial sites owing to structural instabilities of ladders and the negligence of safety measures by users. To prevent accidents involving workers using portable ladders, it is important to encourage workers to use them correctly through laws and regulations; however, establishing effective preventive measures that go beyond regulations can increase acceptance in industrial sites and maximize the effect of reducing industrial accidents. Therefore, this study conducts a fact-finding survey and portable safety ladder product analysis and collects stakeholder opinions to develop a Korean-style safety ladder that can replace step ladders with a high risk of accidents.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 2004.05a
• /
• pp.581-585
• /
• 2004

The purpose of this study is to suggest a method to support decision making of researchers, when we estimate the safety of the high-speed railway using F-AHP. To apply this method, Korean type of high-speed railway was engaged, and the 8 Stages of accident type and the five criteria were suggested that we must meet. Then, the interview with the researchers working for high-speed railway was used to confirm the alternatives suggested. The employed F-AHP for this study estimate using emotional words based on AHP of Saaty, so it is very good to estimate the high-speed railway safety.