• Journal of Korea Foresty Energy
• /
• v.18 no.2
• /
• pp.55-61
• /
• 1999

This study was carried out to investigate the influence of viscoelastic properties(or chemical composition) of a series of ethylen-viny1 acetate copolymers on impact noise and vibration damping of wood/polymer/wood sandwich composites. The impact noise and vibration damping of composites were very sensitive to the state of molecular motion of polymer. The noise and vibration damping of composites were maximum when the polymer was under the glass transition(vinylacetate 55~75%) at the test-temperature, and minimum rubbery state(vinyl-acetate 47~20%) or glassy state(vinylacetate 100~87%). The polymer under glass transition reduced the impact noise by 6~12 dB.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.40 no.3
• /
• pp.48-52
• /
• 2008

Waste paper plastic composites were prepared with old newspaper and old corrugated containers and mixed office waste and those properties were evaluated. The results were summarized as fellows. 1. The strength properties like as tensile and Young's modulus reveled most high level in MOW composite. 2. The coagulation of fibers in paper particle should interrupt equal dispersion of polymer and paper particle. 3. The micrograph of the surface of composites showed the most high dispersion in ONP composite.

• Composites Research
• /
• v.31 no.5
• /
• pp.202-208
• /
• 2018

In this paper, mechanical and hygroscopic properties of teak sawdust and recycled polypropylene (RPP) composites are evaluated and compared with virgin polypropylene (VPP) matrix based composites. Verities of composites are prepared by variation in the plastic types, wood plastic ratio and the addition of coupling agent in the formulations. Mixing of wood sawdust and polypropylene is done by a twin screw extruder, and then sheets of wood plastic composites (WPCs) are produced by using the compression molding method. The results show that recycled matrix composites exhibit better tensile, flexural strength with low impact strength than virgin matrix based composites. Recycled composites show low water absorption and thickness of swelling than virgin matrix based composites. The results confirm that wood content in the polymer matrix affects the performance of composites while presence maleated polypropylene (MAPP) improves the properties of the composites significantly. Developed RPP matrix composites are as useful as VPP matrix composites and have the potential to replace the wood and plastics products without any adverse effect of the plastics on the environment.

• Polymer(Korea)
• /
• v.37 no.2
• /
• pp.204-210
• /
• 2013

Effects of additives (lubricant and antioxidant) and melt-blending condition (temperature, time and rotor speed) on the mechanical properties of polypropylene-based wood polymer composites (WPCs) were investigated. WPCs were prepared by melt-blending followed by compression molding. To understand melt-blending procedure, torque change of the WPC melt-blend was monitored. Maleic anhydride modified PP and nanoclay were used as a compatibilizer and a reinforcing filler, respectively. UTM and izod impact tester were used to measure the mechanical properties of the WPCs and a color-difference meter was used to measure the discoloration of the WPCs according to melt-blending condition. The mechanical properties showed that the optimized melt-blending condition was $170^{\circ}C$, 15 min, and 60 rpm. The mechanical properties of the WPCs decreased with increasing lubricant and antioxidant content. The two step method, adding wood flour later separately during melt-blending, was more effective than the typical one step method for improving the mechanical properties of the WPCs.

• Journal of Forest and Environmental Science
• /
• v.14 no.1
• /
• pp.1-13
• /
• 1998

In this paper, it has been discussed on the relation between the anatomical features of woods and the penetration of methyl methacrylate monomer system into major Korean tree species, especially the Pinus koraiensis, Larix leptolepis, Quercus mongolica and Tilia amurensis. 1. There was some differences in penetration of polymers among different tree species, but generally the penetration of ring porous woods seems to be larger than that of diffuse porous woods and it was very difficult to penetrate to Larix leptolepis, especially to the that of heart wood. 2. The penetration on transeverse surface was relatively easy but radial and tangential impregnation were somewhat hard and differences between them were negligible. 3. The penetration of sapwood was larger than that of heartwood and its differences varied according to the existence of tyloses or contents in vessel. 4. Generally the polymer penetration of earlywood was larger than that of latewood in ring porous woods, but on the contrary, penetration of earlywood was small than that of latewood on diffuse porous woods. 5. Vessel diameter of wood had nearly no relation to polymers penetration. This seems to come from the reason that effective vessel diameter varies with the existence of tyloses or contents in vessel. 6. The penetration of ray tracheids was larger than that of ray parenchyma cells in softwoods, but penetration of hardwood rays seems to be small in comparison with softwood ray parenchyma cells. 7. Specific gravity and annual ring width had no relation to the penetration of polymer.

• Polymer(Korea)
• /
• v.37 no.5
• /
• pp.613-617
• /
• 2013

The effects of nano size kenaf cellulose fiber on mechanical property of polypropylene (PP) composite were investigated. The addition of nano-kenaf in place of natural kenaf showed higher tensile strength, flexural strength, impact strength, and heat deflection temperature compared to the natural kenaf filled PP composite, while it shows lower melt flow index, elongation%, and flexural modulus. These seemed to be due to the increased surface area of nano-kenaf fiber contacting PP matrix and reduced impurities such as volatile extractives on the fiber surface.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2007.11a
• /
• pp.93-102
• /
• 2007

Biocomposite was organized with biodegradable polymer and natural fiber that has potential to be used as replacement for glass fiber reinforced polymer composite with the benefits of low cost, low density, acceptable specific strength, biodegradability, etc. Until now, non-wood fibers have been used as reinforcements of biocomposite which are all plant-based fibers. The present study focused on investigating the fabrication and characterization of biocomposite reinforced with red algae fiber. The bleached red algae fiber(BRAF) showed very similar crystallinity to the cellulose. It has high stability against thermal degradation (maximum thermal decomposition temperature of 359.3$^{\circ}C$) and thermal expansion. Biocomposites reinforced with BRAF have been fabricated by a compression molding method and their mechanical and thermal properties have been studied. The storage modulus and the thermomechanical stability of PBS matrix are markedly improved with reinforcing the BRAF. These results support that the red algae fiber can be used as an excellent reinforcement of biocomposites as "green-composite" or "eco-composite".

• Journal of Korea Foresty Energy
• /
• v.17 no.1
• /
• pp.36-46
• /
• 1998

The aim of this study was to develop the noise and vibration damping wood-based composites by using viscoelastic polymer materials. Polyvinylchloride(PVC) was plasticized with 20-140 phr bis(2-ethylhexyl) phthalate(DOP) and the dynamic tensile mechanical properties were measured at 110Hz and approximate temperature range -100 to 150$^{\circ}$ using a Rheovibron Instrument. The PVC/DOP blends were shown to be compatible in all proportions, and both T(E”$_{max}$) and T(tan${\delta}_{max}$) shifted to the lower temperature side as the DOP content increased. The vibration damping properties of wood/polymer composites were measured using the Rheovibron instrument in a bending mode. The composite damping factor(tan ${\delta}_{c}$) of wood /PVC-DOP/wood sandwich structure correlated with the loss factor and that of the coated structure correlated with the loss modulus(E”) of the polymer layer. In addition, the sandwich structure was found to be more effective in damping than the coated structure. The logarithmic decrement (${\Delta}$c) curve of a sandwich structure, which was determined by the free-free flexural vibration method was similar in shape to the tan ${\delta}_{c}$ curve.

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.2
• /
• pp.155-163
• /
• 2009

This study examined the thermal stability of PLA-WF bio-composites. Wood flour (WF)-filled PLA bio-composites were reinforced with the flame retardants, Melamine pyrophosphate (MPP), resorcinol bis (diphenyl phosphate) (RDP) and zinc borate (ZB). The flame retardant was compounded with PLA and natural biodegradable filler. The thermal properties of the biodegradable polymer and bio-composites reinforced with the flame retardant were measured and analyzed by DSC, DMA and TGA. The results showed that the flame retardant-reinforced biodegradable bio-composite exhibited improved thermal properties.

• Applied Chemistry for Engineering
• /
• v.10 no.1
• /
• pp.46-50
• /
• 1999

Effects of $(NH_4)_2HPO_4$ and boron compounds ($Na_2B_4O_7:H_3BO_3=5:1\;ratio$) on the flame retarding characteristics of the surface modified wood powder-filled polypropylene composites were studied experimentally. The mechanical properties of m-phenylene dimaleimide(PDMI)-modified polypropylene composite were also compared with those of unmodified one. The flame retardance of $(NH_4)_2HPO_4$-modified wood powder composites was more improved than that of boron compounds-modified one. The impact strength of composites increased and the tensile strength of those decreased progressively with an increase of wood powder loading. The mechanical properties of modified polypropylene composites are more improved than those of unmodified one. The tensile strength also increased marginally with increasing the concentration of flame retardants, yielding a maximum when the concentration of flame retardant is 25.0 wt %. And the tensile strength of the composite was increased up to 16 wt % with increasing concentration of PDMI.