• Journal of the Korean Wood Science and Technology
• /
• v.27 no.3
• /
• pp.23-30
• /
• 1999

have been many studies to analyze the behavior of metal plate connector that most widely used to connect light frame wood trusses. Finite element method{FEM) was one of the methods for those studies. FEM using linear model may well be applicable to predict the initial slope of load-displacement curve for metal plate connection. However, displacement may be overestimated above experimental results with the increase of load. Therefore, linear model cannot be used for the nonlinear behavior part. To predict real behavior more exactly, nonlinear term was included to FEM model in this study. It was found out that EA and AA mode showed the high agreement between predicted results and experimental ones. However, EE and AE mode showed a little difference between predicted results and experimental ones in nonlinear part. This results might be caused by insufficient reflection of the slip effect. Consequently, the effect of slip shall be considered to approve the accuracy of nonlinear analysis for the behavior of metal plate connection.

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.4
• /
• pp.96-105
• /
• 2002

Shear wall is the most important component resisting lateral loads imposed to a building by wind or earthquake. In shear walls, lateral load applied to framing is transmitted to sheathing panel through nailed joints between sheathing and framing so that the load is resisted by in-plane shear strength of sheathing. Therefore, nailed joints are the most basic and important component in the viewpoint of stiffness and strength of shear walls. In this study, stiffness and strength of single nailed joint were measured by single shear tests of nailed joints and used as input for theoretical models developed to estimate racking behavior of shear walls. And shear walls were tested to check the accuracy of theoretical models estimating racking resistance of shear walls. Stiffness of nailed joint was affected by grain direction of stud but direction of sheathing panel had little effect. Behavior of nailed joint and shear walls under lateral loads could be represented by three lines. Theoretical model II was more accurate than theoretical model I in estimating racking behavior of shear wall under loads.

• Journal of the Korea Furniture Society
• /
• v.27 no.3
• /
• pp.185-196
• /
• 2016

This study is about watching the changes in Modern and Contemporary ages, through Traditional Ottchil Painting analyzed the formative characteristics presented on 23 pieces of Najeon Master Bong-Ryong Kim. He restored and reproduced the Ottchil Painting Technique by making Najeon ware (lacquer ware inlaid with the mother-of-pearl) on the Korean Modern and Contemporary period. The formative characteristics of his Ottchil Painting Technique are as follows. He used a lot of the Myochilchaehoi Technique as the technique of expression, along with the Najeon Yanggam Technique mixed with Myochilchaehoi Technique. The frame material of Ottchil Painting Ware is handcrafted wood. And in the painting foundation, red is presented more than black. The colors of painting and the pattern drawn on the foundation of Ottchil painting are mainly bright red, blue, yellow, black, and white (five-color). The main pattern used is the dragon, and the subordinate patterns are clouds and Arabesque. Also, the main pattern is solo, and the subordinate pattern is mostly an arrangement combination of radiation symmetry. This style of art was most commonly used for painting fruit trays. As stated above, Bong-Ryong Kim presented various and masterful aesthetic quality based on sincere and exquisite Najeon ware production skills.

• Journal of the Korea Furniture Society
• /
• v.20 no.5
• /
• pp.440-456
• /
• 2009

Because PBD was started as a design tool for steel construction and concrete construction, it was able to applied to the post and beam method of wooden building constructions. But, it may not suitable to light frame wooden construction that is becoming popular in domestic construction market due to the economical efficiency and the constructive simplification. Owing to the share effects between member and sheathing material or among structural members, light frame wooden construction is different from post and beam construction that use a single structural member. Therefore, consideration on the system analysis and system design are urgently needed to use in actual life and inspect the reliability of structures from the system view. With this in mind, code conversion from ASD to PBD that is pressing issue in domestic wooden building construction was studied, also various countries status about PBD were considered and then approaching methods on the system reliability were referred. Finally, several considerations for the development of PBD were explored. PBD should be considered as, not only a new structural design process that select sizes of structural member, but a industrial tool that can lead a development of more reliable wood products. A strongest point of PBD is independent of various construction materials and construction types.

• Journal of the Architectural Institute of Korea Planning & Design
• /
• v.34 no.8
• /
• pp.59-67
• /
• 2018

In a state where ancient buildings was left a lot in the case of Korea, many parts do not remain the documentation, and there is a Kiwarisho lot in Japan, however, the present methods and tree split does not exist in the Korea. However, it is impossible to make a perfect building without splitting exact member when making a building. Thus will not be revealed simply by presumption that there is a similar way to wood comparatively far in Korea. Without a comparison of building dimensions and Korea calculation dimensions Kiwarisho In the first study about the proportionality of Korea, I do not know until now, other studies of the following documents which house a high approximation ratio and member size of Korea consider reason to have is impossible. View compared with respect to the axis of the building in the early stages of research first. In the case of Japan and Korea to form a tree frames in basic form that form the building, the shaft portion is easy to understand and easy compared in common is at most the shaft portion.

• Conservation Science in Museum
• /
• v.15
• /
• pp.122-137
• /
• 2014

The National Museum of Korea own a historical document box ^K976 that was once used to store Joseon Wangjo Sillok ^{Annals of the Joseon Dynasty} of the Joseon Dynasty. The rectangular box has a lid, and the entire surface is varnished with black lacquer. The wood of the box had become warped and the upper part of the wooden frame had been damaged. In some areas, the paint was flaking off, exposing the underlying wood, and an iron ring that connected the lid to the body of the box was missing. Thus, in 2013, Conservation Science Department in National Museum of Korea began to repair and restore the Joseon document box. Before the treatment, analyses were conducted to examine the box's structure, damaged parts, species of wood, and lacquering techniques. The wood was found to be that of a linden tree. As for the lacquering technique, the surface of the box was first coated with a layer of lacquer and bone ash, and then covered with Korean traditional paper. Next, the box was painted with a layer of mud and ashes, followed by a layer of black pigment mixed with soot, and then varnished again with lacquer.

• Journal of agriculture & life science
• /
• v.45 no.6
• /
• pp.21-32
• /
• 2011

This research is intended to study literatures relating to western rocking chairs style in early 20th century in order to provide basic data of designs for rockers of today in Korea and investigate characteristics of rocking chair from academic, formative and pragmatic perspectives. During the first half of 20th century, western rocking chairs (1925~1945) embodied actively the simple functionalism concept that furniture design must follow functionality considerations. Therefore, bare wood rocking chairs were without any surface decoration and tubular steel frame rocking chairs often included black leather upholstery in a bold attempt to express exposed structure. And the fact that tubular steel produced such lightweight furniture was crucial importance. Many Modernist designer created curvaceous lines of new pattern changes in their furniture. The structure of Modern rocking chair became all-important, for stylistic as well as functional reasons. Designers equated exposed structure of tubular steel and wooden frame with integrity and rationality and create an equalitarian style of design. Especially, designers in the early 20th century did use various brilliantly colored upholstery and wooden frame with simple forms of modern characteristics.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.1
• /
• pp.40-47
• /
• 2016

Instead of metal connector generally used on the structural glued laminated timber rahmen joints, the GFRP reinforced laminated plates combining veneer and GFRP (Glass Fiber Reinforced Plastic) and bonded type GFRP rod were used as the connectors. As a result of moment resistance performance evaluation on the joint part applied with these connectors, the yield moment of specimen using the GFRP reinforced laminated plates and GFRP rod pin was measured 4 % lower in comparison to the specimen (Type-1) using the metal connectors, but the initial rotational stiffness was measured 29% higher. Also, the yield moment and rotational stiffness of the specimen using the GFRP-reinforced laminated plates and wood (Eucalyptus marginata) pin showed were measured 11% and 56% higher in comparison to the Type-1 specimen, showing the best performance. It was also confirmed through the failure shape and perfect elasto-plasticity analysis that it showed ductility behavior, not brittle fracture, from the shear resisting force by the pin and the bonding strength increased and the unification of member was carried out. On the other hand, in case of the specimen bonded with GFRP rod, it was impossible to measure the bonding performance or it was measured very low due to poor bonding.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.1
• /
• pp.30-39
• /
• 2016

The evaluation of the lateral load performance for larch glulam portal frames was carried out using glass fiber reinforced plastic (GFRP) as connector in two different systems: the GFRP-reinforced laminated plates combined with veneer, and GFRP rod joints glued with epoxy resins to replace usual metal connectors for the structural glulam rahmen joints. As a result the yield strength, ultimate strength, initial stiffness of glulams of GFRP rod joints glued with epoxy resin decreased to 49%, 52% and 61% compared to those of the conventional metal connector. This connector will be a stress device where the bonding strength between the GFRP rod and glued laminated timber is important. Thus, there will be a high possibility that a problem may occur when it is applied to the field. On the other hand, the GFRP-reinforced laminated plates and wood (Eucalyptus marginata) pin were measured all within 3% for all measurements of the yield strength, ultimate strength, initial strength and ductility factor, regardless of high cross sectional loss on the glued laminated timber slit joint. In addition, the variation of stiffness on the cycle was 35%, which was the lowest, confirming that it was almost the same performance as the specimen prepared with the metal connector.

• Journal of the Korean Institute of Rural Architecture
• /
• v.4 no.1
• /
• pp.29-36
• /
• 2002

The characteristics of the rural dwelling houses of the Korean communities were investigated and analyzed to understand their rural dwelling culture in east-northern China. This research was done by the field survey of rural village, Longshancun, Yanbian. The structures of their houses are changed into the brick houses from the earthen houses with wood frame. The floor plans are changed into Dual-bay-type of Divided-space from Single-bay-type of Hollistic-space, the largest ratio at present, and the numbers of space are increased. In the view of total outline, their dwelling houses are based to those of east-northern Korea and are sustained to the vernacular dwelling styles(ex : floor heating, ondol, and sit-down), and are adapted to the geography and climate of Yanbian and accepted to the culture of other communities(ex : indoor-kitchen, indoor-removing-shoes).