• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.1
• /
• pp.84-87
• /
• 2016

In this paper, a receiver for wireless power transfer is proposed. The receiver consists of a 100 W rectifier in 1.8 MHz frequency band, and a constant current charger. In particular, two kinds of protection circuits are installed in the rectifier. They are a over-voltage protection circuit which block the input voltages greater than 30 V and a active-dummy load which maintains the receiver input impedance by automatically consuming the remaining input power. The constant current charger is designed to charge the battery with a charging current of up to 1 A. A wireless charging system is fabricated using the proposed receiver. The system is composed of a 130 W transmitter, two magnetic resonator, and proposed receiver for charging a 48 V Li-Ion battery using the coupled magnetic resonance method. By the measurement result, the system efficiency is about 54 %.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.6
• /
• pp.679-689
• /
• 2014

In this paper, an analysis of the effect of time-variant reflected impedance and its detection method on wireless power transfer(WPT) systems are presented. The reflected resistance at WPT systems is very important parameter as it indicates how well matched antenna is and will exhibit high efficiency. Proposed detection method is based on transmitter current variation analysis with respect to frequency sweep. Using the proposed design method, a wireless power transfer system operating at the frequency of 125 kHz, is design and detect reflected impedance variation. The proposed design method provides good agreements between measured and simulated results. Therefore, The proposed detecting method provides a nonintrusive method to detect harmful object in WPT system.

• Journal of Convergence for Information Technology
• /
• v.8 no.6
• /
• pp.237-242
• /
• 2018

There are various 'wireless communication technologies' around us. Wireless mobile communication has evolved through various stages, and its utilization is also diverse. However, due to the development of wireless communication technology, the demand for frequency resources is much higher than the supply, so frequency shortage is serious. Recently, 'visible light communication' has been attracting attention as an emerging communication technology that can solve the frequency shortage. 'Visible light communication' is a communication method based on serial data transmission / reception, and there is a difficulty in transmitting / receiving parallel data because the transmitter and the receiver are arbitrarily present. In this paper, we have studied parallel data processing of visible light communication. We could solve the problem by analyzing parallel data using image processing. Through this study, communication performance can be verified through I / O data comparison by implementing parallel data analysis method. It is expected that diversity in parallel data analysis will be presented through the results.

• Biomedical Engineering Letters
• /
• v.8 no.4
• /
• pp.365-371
• /
• 2018

Uninterrupted monitoring of multiple subjects is required for mass causality events, in hospital environment or for sports by medical technicians or physicians. Movement of subjects under monitoring requires such system to be wireless, sometimes demands multiple transmitters and a receiver as a base station and monitored parameter must not be corrupted by any noise before further diagnosis. A Bluetooth Piconet network is visualized, where each subject carries a Bluetooth transmitter module that acquires vital sign continuously and relays to Bluetooth enabled device where, further signal processing is done. In this paper, a wireless network is realized to capture ECG of two subjects performing different activities like cycling, jogging, staircase climbing at 100 Hz frequency using prototyped Bluetooth module. The paper demonstrates removal of baseline drift using Fast Fourier Transform and Inverse Fast Fourier Transform and removal of high frequency noise using moving average and S-Golay algorithm. Experimental results highlight the efficacy of the proposed work to monitor any vital sign parameters of multiple subjects simultaneously. The importance of removing baseline drift before high frequency noise removal is shown using experimental results. It is possible to use Bluetooth Piconet frame work to capture ECG simultaneously for more than two subjects. For the applications where there will be larger body movement, baseline drift removal is a major concern and hence along with wireless transmission issues, baseline drift removal before high frequency noise removal is necessary for further feature extraction.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.15 no.1
• /
• pp.8-13
• /
• 2022

This paper investigates the method to implement a RF (Radio Frequency) energy harvesting sensor node and to build a sensor network using a CATV network and a leaky coaxial cable. The power supply of a sensor node is designed with the WPTS (Wireless Power Transfer System) receiver operating at 915MHz. A sensor network has limited coverage by the loss of RF signal at a wireless transmission link. The paper proposes to build a sensor network that the BLE signal of a sensor and the signal of a WPTS power transmitter are transmitted through a coaxial cable of a CATV network by utilizing WOC (WiFi over Coax) technology and radiates at a leaky coaxial cable. The length of a leaky coaxial cable and the total loss of a wire link are allowed to the point that the RSSI of a sensor node is more than the minimum value (-78dBm) and lead to extend wireless coverage.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.8 no.3
• /
• pp.9-14
• /
• 2008

In this paper, we propose the channel sounding scheme which is made for ideal communication between some application as well as the short distance of high speed data transmission in MIMO-OFDM system for Wireless PAN. This method is able to perceive the duration of the impulse response through the delaying of power delay profile, modeled a power delay profile which has an attenuate characteristic, and obtained the coefficient of channel response by ML (maximum likelihood). Through the amplitudes, phases and delays associated with each multipath component which were acquired from this channel sounding scheme, we can describe the wave propagation characteristics of channels between the transmitter and receiver so that the receiver could enhance not only the reliability but also the ability of communication link.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.10
• /
• pp.2247-2253
• /
• 2010

WiBro(Wireless Broadband Internet) is the standard of high-speed portable internet based on OFDMA/TDD (Orthogonal frequency division multiple access / Time division duplexing) techniques, and the subset of consolidated version of IEEE802.16e Wireless MAN standard. In this paper, we propose performance improvements of WiBro system using the LVQ(Learning Vector Quantization) blind equalization. Proposed method used the prefiltering LVQ neural network blind equalization in the Broadband WiBro system receiver. The prefiltering LVQ neural network constellates 16QAM that is transmitter data shape and the blind equalization removes ICI(Inter Carrier Interference). To verificate the proposed method usability, the MSE(Mean Square Error) and the BER(Bit Error Rate) are simulated. The simulation results shown that is improved the performances of the proposed WiBro system using the LVQ blind equalization than the existing WiBro system.

• The Journal of the Acoustical Society of Korea
• /
• v.23 no.2
• /
• pp.134-145
• /
• 2004

The study aims to develop the underwater wireless telephone system. The system is designed based on the underwater acoustic communication channel parameters such as ambient noise, multipath effect and diver breathing noise. The system adopts SSB modem and its carrier frequency is about 33 kHz in which ambient noise level is low and therefore a high S/N ratio is easily obtained. The source level of the transmitter is designed as 131 dB re 1μPa. Its intelligibility index of sentence shows as 80% or mure in the range of less than 300m in the sea trial.

• ETRI Journal
• /
• v.25 no.5
• /
• pp.328-336
• /
• 2003

Bluetooth is a specification for short-range wireless communication using the 2.4 GHz ISM band. It emphasizes low complexity, low power, and low cost. This paper describes an area-efficient digital baseband module for wireless technology. For area-efficiency, we carefully consider hardware and software partitioning. We implement complex control tasks of the Bluetooth baseband layer protocols in software running on an embedded microcontroller. Hardware-efficient functions, such as low-level bitstream link control; host controller interfaces (HCIs), such as universal asynchronous receiver transmitter (UART) and universal serial bus (USB)interfaces; and audio Codec are performed by dedicated hardware blocks. Furthermore, we eliminate FIFOs for data buffering between hardware functional units. The design is done using fully synthesizable Verilog HDL to enhance the portability between process technologies so that our module can be easily integrated as an intellectual property core no system-on-a-chip (SoC) ASICs. A field programmable gate array (FPGA) prototype of this module was tested for functional verification and realtime operation of file and bitstream transfers between PCs. The module was fabricated in a $0.25-{\mu}m$ CMOS technology, the core size of which was only 2.79 $mm{\times}2.80mm$.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.3 s.357
• /
• pp.92-97
• /
• 2007

Switching mode amplifiers have been studied widely for use at microwave frequency range, and the class E amplifier which is a type of switching mode amplifier offers very high efficiency approaching 100%. In this paper, 2.4GHz microwave class E amplifier with 66% power added efficiency (PAE) and 17.6dBm output has been linearized for use at wireless LAN transmitter, and digital predistortion technique with look up table is applied. With -3dBm input power of wireless LAN, measured output spectrum can meet the required IEEE 802.11g standard spectrum mask, and the digital predistortion output spectrum has been improved by 5dB of ACPR at 20MHz offset from center frequency.