• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.271-274
• /
• 1999

This paper proposes a simple architecture of digital dividing block in dual-modulus prescaler phase-locked loop used in the wireless communication. Proposed architecture eliminates a swallow counter in the conventional one and demonstrates the advantages in reducing the power consumption and the gate-counts. Therefore, it is suitable for small die area and low power applications. The circuit is designed in a standard 0.35${\mu}{\textrm}{m}$ CMOS process.

• Journal of the Korean Operations Research and Management Science Society
• /
• v.36 no.3
• /
• pp.45-59
• /
• 2011

OFDMA systems have been expected to be widely used to provide multimedia services over wireless channels. To evaluate performance of the OFDMA system, power should be considered as system resource as well as subcarriers. This study propose a queueing traffic model incorporating two kinds of resources (power and subcarriers), and an extended model giving a priority to handoff calls over new calls. Some extensive experiments are conducted to illustrate the usefulness of the proposed traffic model.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2018.10a
• /
• pp.503-505
• /
• 2018

본 논문에서는 마이크로파 무선전력전송에서 성능을 열화시키는 요인인 주파수 오프셋 문제와 위상 오차에 대해서 다룬다. 2.4GHz 대역을 사용하는 무선랜 표준에서 주파수 오프셋을 추정하기 위한 알고리즘을 소개하고 수신 전력을 증가시키기 위한 RF 빔포밍에 대해서 논의하였다.

• Proceedings of the KIPE Conference
• /
• 2013.07a
• /
• pp.315-316
• /
• 2013

This paper presents a parameter tuning method of a LLC resonant converter for a wireless charging circuit. A switched-capacitor is used to change the resonant frequency of the resonant circuit. The simulation results verify that the efficiency of the power transfer can be improved by a duty control of the switched-capacitor for various values of the coupling coefficient.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.881-885
• /
• 2008

Wireless energy transmission system to a Micro Aerial Vehicle is now under development. A 5.8 GHz microwave phased array antenna and rectenna array receiver have been developed. An electric motor on a circling MAV model was driven by the transmitted power. In addition, 140GHz millimeter-waves of up to 1MW was beamed to a "Microwave Rocket" and its thrusting has been successfully demonstrated.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.1
• /
• pp.182-187
• /
• 2009

In this paper, the power management module of wireless sensor node is designed and fabricated utilizing RF energy from reader antenna of commercial RFID system, which is mainly categorized in the energy harvesting. For this, the rectenna and the high efficient boost converter is designed to get the DC power from RF power for the charging the battery. When the RF power from RFID reader antenna is 1.2[W], the DC power of 3.1[mW] at the distance of 1[m] and 1[mW] at 5.5[m] are obtained. Considering the connection to the battery, the boost converter for enhancing the conversion efficiency is designed. The conversion efficiency at the distance of 4[m] is 79.3[%] and the harvested power is 1.36[mW] which is actually used for the charging the battery. This value is available in the wireless sensor networking.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.26 no.6
• /
• pp.437-445
• /
• 2021

This paper proposes an operating frequency design method that limits the voltage applied to aload-side converter during the initial operation of a loosely coupled resonant dual-active bridge (LCR-DAB) converter and an initial operating strategy that applies it. The LCR-DAB converter uses two wireless power transfer coils instead of the high-frequency transformer of the general DAB converter. The wireless power coil has a physical distance of several tens of millimeter or more between the two coils; thus, the LCR-DAB converter is a bidirectional isolated power conversion system that can easily achieve high insulation performance. However, for the initial operation of the LCR-DAB, if the power-side converter is operated at the resonance frequency while the load-side converter is not operating, then a very high voltage due to resonance is applied to the load-side converter, thereby causing damage to the converter. Therefore, a method that can stably charge the DC link voltage of the secondary-side converter during the initial operation is needed. This paper proposes a method to initially charge the secondary-side DC link by operating the primary-side converter at a frequency with limited voltage gain rather than at a steady-state operating frequency. The validity of the proposed frequency design method and initial operating sequence is verified through simulation and experimentation of the 1 KW LCR-DAB converter.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.6
• /
• pp.593-596
• /
• 2015

In this paper, we design a high efficiency class E power amplifier operating at low drain bias voltage for wireless power transfers. A 13.56 MHz power amplifier is designed at drain bias voltage of 12.5 V using Si MOSFET with the breakdown voltage of 40 V. High quality-factor solenoidal inductor is designed and fabricated for use in output matching circuit to improve output power and efficiency. Input matching circuit simply consists of resistor and inductor to reduce the circuit area and improve the stability. The fabricated power amplifier shows the measured output power of 38.6 dBm with the gain of 16.6 dB and power added efficiency of 89.3 % at 13.56 MHz.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.24 no.1
• /
• pp.62-65
• /
• 2019

Wireless power transfer systems require an algorithm to determine the presence of the target object for mitigating standby power and safety issues. Although many schemes that sense various external objects have been actively proposed for inductive power transfer systems, not many studies on capacitive power transfer systems have been conducted compared with those on inductive power transfer systems. This study proposes a target object detection algorithm by monitoring the capacitance in transmitter-side electrodes without additional pressure sensors or distance sensors. The proposed algorithm determines the presence of a target object by monitoring the change in capacitance in transmitter-side electrodes using the step pulse of the microcontroller unit. The algorithm is verified by two step processes. First, the performance in capacitance measurement is compared with that of an LCR meter. Then, the verification is conducted in a 5-W capacitive power transfer hardware. Experimental result shows that the interelectrode capacitance increases by 6 times when the target object is fully aligned. Thus, the proposed scheme can successfully detect the presence of the target object.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.969-972
• /
• 2015

Many studies have been carried out in order to develop a frequency efficient communication system than the current communication system for satisfying the increasing demands of wireless data services in mobile communication systems. If a communication system dramatically improving the frequency utilization efficiency is not developed, service providers must maintain more number of base station equipments to meet the increasing demands of wireless data service. Service provider needs a system or method to reduce maintenance costs. Demands of wireless data service are changed according to time of day, location and so on. Power consumption can be reduced if the supplied power of communication systems is controlled by wireless data traffics. This paper describes the design and implementation of power management system of mobile communication base station's equipment based on smart grid. The proposed power management system controls the supplied power to the mobile communication infrastructures depending on the demand of wireless data. Field test results of the implemented system show the proposed system saves 26% of the power consumption in the base stations.