• 한국철도학회논문집
• /
• 제8권6호
• /
• pp.525-532
• /
• 2005

Fatigue life of catenary wires in various environments is reduced when stress is concentrated on some points, which are often found in corroded areas by surrounding pollutants. Therefore, the fatigue test were performed in order to investigate the effect of the surface corrosion on the destructive behavior in service environment and accelerated corrosion environment as well as th examine the corrosive property and mechanism of the catenary wires. In the fatigue test of the messenger stranded wire, the corrosion degraded materials showed 35~50% of fatigue life at a same stress amplitude compared to original material. Because the catenary wires have variable load by the interaction of periodic contacts with pantographs the maximum stresses of trolley wire and messenger wire calculated by simulation at the messenger wire during operation was estimated thought the corrosion behavior interpretation of variable stress and fatigue test.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 추계학술대회 논문집 전력기술부문
• /
• pp.246-248
• /
• 2004

The lower voltage distribution box of service wire has been usually employed to supply an electric power to the consumers through low voltage overhead line. Now-a-days, electric shock accident at the distribution box of service wire installed in the seashore areas has been often occurred. The reason is mainly due to the electric leakage in the distribution box of service wire. This paper described insulation breakdown mechanism of distribution box of service wire, analysis of electric shock path and safety countermeasure of distribution box of service wire.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제33회 춘계학술대회 개최
• /
• pp.319-326
• /
• 2001

The sliding wear characteristics of carbon steel castings were Investigated using a ball on disk type tester. The experiment was conducted using high carbon steel wire rods as ball material and carbon steel castings as disk material and different operating conditions, at room temperature under a lubrication and dry conditions. The results showed that the carbon steel castings appeared average wear volume Is lowed after annealing under a lubrication conditions and wear curve linear Increased. The specific wear rate of carbon steel castings Increased with wire diameter lubrication and dry also Increased 125 times In Ory. The sliding wear mechanism were Investigated due to fatigue wear lubrications and abrasive wear dries also wire Included fatigue and abrasive wear by plastic flow.

• 항공우주시스템공학회지
• /
• 제12권5호
• /
• pp.69-75
• /
• 2018

본 논문에서는 전기 접속부 역할을 하는 포고핀을 활용한 극초소형 위성용 나일론선 절단방식 태양전지판 분리장치를 제안하였다. 제안된 분리장치는 종래 나일론선을 이용한 분리장치에 비해 높은 체결력 및 횡/종방향 동시구속이 가능하고, 체결작업이 용이하며, 또한 다수의 태양전지판의 동시분리가 가능한 장점을 갖는다. 또한 제안된 분리장치에 적용된 포고핀은 전력공급을 위한 전기 접속부 기능과 함께 전개 상태 스위치 및 태양전지판의 분리 스프링 역할이 동시에 가능하다. 본 논문에서는 제안된 포고핀 분리장치의 기능성 입증을 위해 체결횟수에 따른 분리 기능시험을 통해 기능성을 검증하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 추계학술대회 논문집
• /
• pp.29-30
• /
• 2010

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1991년도 추계학술대회 논문집 학회본부
• /
• pp.119-121
• /
• 1991

Multifilamentary superconducting wires exposed to an alternating field generate the coupling loss and hysteresis loss. The geometric shapes of multifilamentary superconducting wire are very complicate, and loss generating mechanism is too. In this paper, coupling loss of superconducting wire in case of twelve filament is calculated by two dimensional numerical analysis, and compared with value of conventional formulus. The basic idea of this calculating method is potential difference of external transverse field.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1690-1695
• /
• 2007

Lightweight metallic truss structures with open, periodic cell are currently being investigated because of their multi-functionality such as thermal management and load bearing. The Kagome truss PCM has been proved that it has higher resistance to plastic buckling, more plastic deformation energy and lower anisotropy than other truss PCMs. The subject of this paper is an examination of the failure mechanism of Wire woven Bulk Kagome(WBK). To address this issue, the out-of-plane compressive responses of the WBK has been measured and compared with theoretical and finite element (FE) predictions. For the experiment, 2 multi-layered WBK are fabricated and 3 specimens are prepared. For the theoretical analysis, the brazed joints of each wire in WBK are modeled as the pin-joint. Then, the peak stress of compressive behavior and elastic modulus are calculated based on the equilibrium equation and energy method. The mechanical structure with five by five cells on the plane are constructed is modeled using the commercial code, PATRAN 2005. and the analysis is achieved by the commercial FE code ABAQUS version 6.5 under the incremental theory of plasticity.

• 한국항공우주학회지
• /
• 제42권6호
• /
• pp.529-534
• /
• 2014

전개형 우주 구조물의 구속 및 분리를 위해 일반적으로 적용되는 폭발식 분리장치의 경우, 극초소형 위성으로 분류되는 큐브위성에는 적용불가가 설계요구조건으로 규정되어있다. 큐브위성의 제한된 장착 공간과 이로 인한 저충격 요구조건, 저가의 개발비 등의 요구조건으로부터 일반적으로 적용이 용이한 나일론선 열선절단방식이 적용되고 있다. 하지만 나일론선 적용에 따른 낮은 체결력과 복수 구조물의 구속/분리를 위해 복수의 체결부와 열선을 필요로 하는 등 시스템 복잡화 및 신뢰도 저하의 문제점이 존재한다. 본 연구에서는 상기의 문제점 해결을 위해 힌지 구동형 분리너트를 적용한 구속분리장치를 제안하였으며, 인증시험 온도범위에서의 분리장치 동작 기능시험, 정하중 시험, 충격레벨 측정시험을 통해 설계의 유효성을 입증하였다.

• 한국공작기계학회논문집
• /
• 제16권2호
• /
• pp.50-56
• /
• 2007

Wire forming machine is widely used in industries to make a variety of wire products such as coil springs and links. Along with the rapid development of CNC technologies, the usage of wire forming machine varies from single-purpose machinery to universal CNC machinery. Rotating the wires while feeding them simultaneously, we can improve the performance of the machines with aspects of efficient tooling and complicated geometric forming. In this study, a new gear train is developed for the control of both feeding and rotating wires independently at the same time. The developed mechanism has many benefits as following, making more complicated geometric and precision products, easier tooling, and simpler programming.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.1662-1667
• /
• 2005

In this paper, analysis, design, control and prototype construction of a wearable wire-driven haptic interface called HapticPen is discussed. This device can be considered as a wire driven parallel mechanism which three wires are attached to a pen-tip. Wire tensions are provided utilizing three DC servo motors which are attached to a solid frame on the user's body. This device is designed as input as well as output device for a wearable PC. User can write letters or figures on a virtual plate in space. Pen-tip trajectory in space is calculated using motor encoders and force feedback resulting from contact between pen and virtual plate is provided for constraining the pen-tip motion onto the virtual plane that can be easily setup by arbitrary non-collinear three points in space. In this paper kinematic model, workspace analysis, application analysis, control and prototype construction of this device are presented. Preliminary experiments on handwriting in space show feasibility of the proposed device in wearable environments.