• International Journal of Aerospace System Engineering
• /
• 제7권1호
• /
• pp.1-6
• /
• 2020

A deployment mechanism is designed to stow into a small volume efficiently. The panels are fabricated by carbon fiber reinforced plastics (CFRPs). The parameters for the deployment are determined by considering the number of panels, the folding/twisting angles, and the driving force for a deployment device. In addition, a surface accuracy of the manufactured reflector is measured through a photogrammetry methodology. The deployment behavior of CFRP reflector is observed by using the zero-gravity device which compensates the gravity effect during the deployment. The zero-gravity device is constructed wire, motor, controller and loadcell. During the deployment of the reflector panel, the wire and motor compensate for its weight by the feedback process of the controller. Tests result show that a zero-gravity device compensates for the weight of the panel during the deployment of the CFRP reflector.

• 대한안전경영과학회지
• /
• 제21권2호
• /
• pp.9-14
• /
• 2019

Gondola is widely used as a construction facility to perform external finishing work without using scaffolding at a construction site. However, since 2000, there have been 17 deaths from now so these risks associated with work can not be ignored. Therefore, it is expected that it will contribute greatly to prevent related disasters if introducing necessary measures to prevent repeated related disasters and installing additional safety devices. In order to eliminate the risk factor according to the operation of the gondola, it is necessary for the operator to use it to use it while the examination of each product is completed, and to use the over load Dangerous arbitrary measures such as arbitrary operation of the prevention device, removal of the safety fence for convenience of work, installation of the wire rope installed in the air, falling out of the wire rope and falling to the ground Do not perform such sealing measures so that any operation of the overload prevention device can not be done so as not to take such arbitrary measures, or wire the power supply wire to the safety fence so as not to delete the safety fence. Then, when the safety fence is removed, so that it does not become a gondola operation, or when replacing the wire rope in the air, to prevent the wire rope from coming off, Additional measures such as installing falling down prevention device may be necessary.

• 산업공학
• /
• 제9권1호
• /
• pp.63-71
• /
• 1996

A wire harness is an assembly cables and/or wires to transmit signals between electronic assemblies in automobiles and electronic appliances. Inspection of such a wire harness is to check the sequence of assembled cabled each of which is identified by its own color. This paper presents an automated visual inspection system for wire harnesses incorporating back-propagation neural network as a color identification device. The tests performed by using real test specimens show that the inspection system works well enough.

• 한국군사과학기술학회지
• /
• 제5권2호
• /
• pp.116-122
• /
• 2002

Electro Explosive Devices can be susceptible to electromagnetic interference. When these components are exposed to external electromagnetic fields, it may cause to induce sufficient current to generate enough heat for an inadvertent detonation. It is almost impossible to monitor the event of firing throughout the electromagnetic environment test. The survivability of EED for hazards of electromagnetic radiation is investigated. A fiber optic sensor is installed near the bridge wire after removing explosive material in order to measure the induced current on the bridge wire. The length of lead-wire of the EED fabricated is around 15 cm.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 추계학술대회논문집
• /
• pp.629-635
• /
• 2000

Vibrational characteristics and tension fluctuation of a translating wire in WEDM are the main problems to deteriorate the cutting accuracy and processing performance. In this paper, we analyze natural frequencies of the wire used in WEDM, both theoretically and experimentally. To reduce the tension variation of the wire. which directly affects cutting performance. we have designed a simply tension reduction device using springs and rollers. It is shown that tension fluctuation is reduced about 25% using the passive tension controller.

• 한국통신학회:학술대회논문집
• /
• 한국통신학회 1986년도 춘계학술발표회 논문집
• /
• pp.107-112
• /
• 1986

This paper presents one method to resolve the end-to-end digital connectivity through 2-wire subscriber loop. This system which consists of the subscriber`s device and the line termination device makes use of the advantages of time compressed multiplexing and modified DPSK. Experimental results show that the transmission range of the lab test covers 2km and that of the field test covers 1.5km.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 춘계학술대회 논문집
• /
• pp.39-40
• /
• 2008

• 소성∙가공
• /
• 제15권6호
• /
• pp.421-427
• /
• 2006

Drawing process of Al-1%Si bonding wire considering fine Si particle is analyzed in this study using FE-simulation. Al-1%Si boding wire requires electric conductivity because Al-1%Si bonding wire is used for interconnection in semiconductor device. About 1% of Si is added to Al wire for dispersion-strengthening. Distribution and shape of fine Si particle have strongly influence on the wire drawing process. In this study, therefore, the finite-element model based on the observation of wire by continuous casting is used to analyze the effect of various parameters, such as the reduction in area, the semi-die angle, the aspect ratio, the inter-particle spacing and orientation angle of the fine Si particle on wire drawing processes. The effect of each parameter on the wire drawing process is investigated from the aspect of ductility and defects of wire. From the results of the analysis, it is possible to obtain the important basic data which can be guaranteed in the fracture prevention of Al-1 %Si wire.

• 한국기계가공학회지
• /
• 제14권2호
• /
• pp.31-37
• /
• 2015

Recently, mobile phones have become necessary tools for everyday life. In this study, a device that can serve as a separation between a touch panel and an LCD module in a mobile phone was devised for mass repair processes at a smaill business. We used a wire cutting method to separate the bonding plate area between the modules. The device is composed of DC motors and stepping motors that can deliver a precise cutting motion. The motor control system is connected by individual control modules to a CAN network. The developed device showed excellent performance at high temperature conditions.

• 한국기계가공학회지
• /
• 제7권4호
• /
• pp.50-55
• /
• 2008

CNC wire bending machines are used in industries to make a type variety of wire products such as long links. The machines have a long arm device to rotate in order to remove forming errors by flexibility of wire. Generally, the machines which constructed servo motors in the arm have the rotating range of the arm under 360 degree because the servo motors connect with fixed control devices on frame by many cables. The rotating angle under 360 degree limits working speed and forming geometry. Therefore this study developed a gear train to drive a parts in arm and to be independent on arm rotation movement. The developed gear train can transfer four movements to four components in arm and is consists parallel of four pairs of satellite gear trains. This study constructed the CNC wire bending machine with the developed gear train and verified that the gear train could drive internal components independently on arm rotation.