• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.50 no.3
• /
• pp.396-406
• /
• 2014

Shrimp beam trawl fishery is one of the important coastal fisheries in Korea. It has a regulation to the length of beam (8m) and wing net (7m) of shrimp beam trawl that has been used in the district of Junlanam-do and Gyungsangnam-do. This regulation was made in relation to the size of shrimp beam trawler of 3-ton class at that time. Now the shrimp beam fishing vessel has a limit not greater than 5 tons in gross ton. Recently, with improvement of fishing industry and fishing vessel fishermen asked the expansion of the length of beam and wing net, therefore it is necessary to investigate the effect of lengthening the beam and wing net length. Three different beams (8m, 10m and 12m in length) and three different wing net (7m, 10m and 13m in length) were made and the experiment was conducted near Narodo of Goheng by two fishing vessels of 4.98 and 4.88 tons in gross ton between June 2011 and October 2012. When the length of wing net was increased from 7m to 10m and 13m, the relative catch ratio in total biomass was increased 25% and 79% for shrimp, (17% and 22% in total), respectively. And when the beam length was increased from 8m to 10m and 12m, the relative catch ratio was increased 35% and 84% for shrimp, (21% and 37% in total), respectively. The force exerted to the iron guide of inhauler's with the beam length of 8m was about 30% greater than that with the beam length of 10m when hauling the shrimp beam trawl net.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.36 no.4
• /
• pp.281-286
• /
• 2000

To analyze the shape of the net mouth of bottom trawl which is composed with 6 seams net, the field experiment was carried out on the sea near Kokunsan Is, Western sea of Korea. The distance of otter board, net height, trawl speed and resistance of the fishing gear were respectively measured according to the change of warp length and towing speed. The results obtained are summarized as follows : 1. The spreading distance of the otter board has been increased straightly according to the increment of towing speed and warp length. The rate of increase by the warp length has been greatly higher than the rate of increase by the towing speed. The total variation of the spreading distance was 57.0-82.8m, and it was occupied 43-62% of the hand rope, net pendent and the length of nets. 2. The height of net mouth has been decreased straightly according to the increment of towing speed and warp length. The rate of decrease by the towing speed has been greatly higher than the decrease rate of the warp length. The total variation of the net height was 3.1-4.0m. 3. When the distance of wing tip is increased, the height of net mouth is decreased, but the ratio of the decreasing rate of the height of net mouth for the increasing rate of the distance of wing tip was gradually low according to the increment of warp length. 4. The ratio of the distance of both wing tip for the height of net mouth has been increased gradually according to the increment of towing speed and warp length, and the total variation of the ratio was 4.17-7.81 times.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.22 no.4
• /
• pp.49-55
• /
• 1986

The authors carried out an experiment to determine the horizontal opening of the mid water trawl gear, which is the same as was used in the foreward experiment concerned to the attitude and opening efficiency of otter board. The trawl net .used in the experiment was designed to have a square sectional four-seamed body with two three-sepenlted wings. Each wing tip was rigged with a net pendant of 70 m long and the fore ends of the pendants were directly jointed to the otter pendant without inserting hand rope, and a front weight of 200 kg weigh was rigged with in front of the lowest wing tip. To determine the opening between otter boards ani between wing tips, two 50 KHz fish finders were set sideways on the otter board and on the port middle wing tip so as to detect the distance froa the finders to the starboard otter board and to the wing tip respectively, and the informations were transmitted to the indicators onboard the ship through water-tight cables. The results obtained can be summarized as follows: 1. The openings between otter borads were 43-45 m in case of the warp 100 m, 53-55 m in the war;> 150 m and 54-59 m in the warp 200 m. It was increased in linear according to the increase of towin; speed in the range of 1. 1-1. 8 mlscc. 2. The determined values of the openings between otter boards were greater than the estimated values. which were calculated by the opening between warps at the gallows of the ship and the length of tt~ warp, assuming that the warps from the top rollers to the otter boards were straight. The rates of the determined values to the estimated values were 1. 23-11. 0 in case of the warp 100 m, 1. 23-1. 12 in the warp 150 m and 1. 23-1. 15 in the warp 200 m respectively. The rates were almost the same at the slow towing speed of 1. 3 mlscc or so, then the higher the speed, the less the rate, and the longer the warp, the greater the rate. 3. The rates of the openings between otter boards to the total length of net pendant and the net (excluded cod end) showed 43-43% in case of the warp 150-200 m. It was a little smaller than th~ standard. which is 50%. in the common bottom trawl. 4. The determined openings between wing tips were 18-19 m in case of the warp 100m, 21-22 m in the warp 150 rn, They showed that the higher the speed, the greater the openings even though its range was no more than 1 m or so. 5. The rates of openings between otter boards to th~ openings betwee:l wing tips were almost invariably 38%. 6. The rates of openigs b2tween otter boards to the lenth of h~ad rope were 60-65% in cas': of th~ warp lOa-150m. It were much larg2r than th~ standard. which is 50%. in the common botto:n trawl.

• Journal of Fisheries and Marine Sciences Education
• /
• v.5 no.2
• /
• pp.90-97
• /
• 1993

Pair trawling is one of the important fishing methods for Korean fisheries, and is working in the western sea of Korea - the Yellow Sea and the East China Sea. On the engine power of the trawlers, 72% of 190 pairs of trawlers were equipped with 450ps class engine, and 21% with 450~750ps and merely 7% with in 750ps class 1980. Thereafter the engine power has grown up, so that 450~750ps occupy 28% and 750ps or more 27% in 1992. Main objective fishes of pair trawling were traditionally flat fishes, so the fundamental shape of pair trawl net was a four - seam net, but by the gradual shortage of flat fishes, roundfishes has been noticed. So the six - seam net which performs high opening of net mouth has been used widely since 1985. In the six - seam net, the length of wing was not so short in the beginning but became short in the later instead of the net pendant elongated, and also the pendant was separated into three pieces according to the change of wing structure. Since the 1990's, the objective fishes has gradually been changed into pelagic fishes, the fishing technique is required to fit the behavior of fishes. So the midwater trawling or the multi -layer trawling became required.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.36 no.4
• /
• pp.299-308
• /
• 2000

A model experiment on the anchovy boat seine was carried out in the southern sea of korea to analyze the vertical opening and the underwater geometry. The model net A was made of half size in the length and width of the prototype net. The model net B was attached floats and chain to the model net-A. The vertical opening and the underwater geometry of the model net were determined by distance of Minilog position with the combinations of the distance between paired boats and the towing speed. The results obtained can be summarized as follows; 1. Vertical opening of the model net was gradually lowered according to the increase of the distance between paired beats and the towing speed. 2. Vertical opening of Wing net, In side wing net, Square, Fore bag net, Flapper and After bag net of the model net A according to the distance between paired boats were varied in the range of 10.8~9.0, 12.0~8.3, 12.6~9.0, 10.4~6.6, 4.6~5.2, 8.8~7.7m respectively, varied in the range of 36~30, 21~15, 31~22, 80~51, 80~96, 59~51% of the normal opening respectively 3. Vertical opening of Wing net, In side wing net, Square, Fore bag net, Flapper and After bag net of the model net B according to the distance between paired boats were varied in the range of 9.1~8.5, 9.8~6.5, 11.2~8.0, 11.0~8.1, 4.7~5.0, 7.0~7.5m respectively, varied in the range of 30~28, 18~12, 27~20, 85~62, 87~93, 47~50% of the normal opening respectively 4. Vertical opening of each a part of the model net according to the towing speed was as same as the former. 5. Model net was appeared apparent the pocket shape, because Wing net and Inside wing net was opened 30% of the normal opening. 6. The bosom and the bag net of the model net A were risen up to the upper lazer, this phenomenon was more apparent as the distance between paired boats and the towing speed increase, but the model net B was almost constant. 7. Working depth of the model net was gradually hallowed according to the increase of the distance between paired boats and the towing speed

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.29 no.3
• /
• pp.200-213
• /
• 1993

A model experiment on a midwater rope trawl net which is used in the North Pacific to catch alaska pollack is carried out in the circulating tank to examine the basic efficiency of the net. The prototype is the net used by M/S Hanil(1, 179GT, 2, 700PS), a Korean trawler. The model net was made according to the Tauti's Similarity Law of Fishing Gear in 1/100 scale by considering the condition of the tank. To measure the basic efficiency of the standard model net, the vertical opening and width between some points marked on the net were measured, and the hydrodynamic resistance were determined. Then the constructive conditions of the net were varied as follows and the factors were measured again to compare the efficiency of those nets with that of the standard net(A-1 type) front weight multiplied 1.5 times: A-2 type. buoyancy and depressing force multiplied 1.7 times: A-3 type. front weight multiplied 1.5 times on A-3 type: A-4 type. depressors rigged at ground rope: B type. cod-end stuffed with cashmylon wad: C type. The results obtained can be summarized as follows: 1. The vertical opening at the center of head rope was steeply decreased with the flow velocity increasing and the vertical opening H(m) can be expressed in H=1.2v super(-1.2)(v : flow velocity in m/sec). The width of the net varied a little when the flow velocity was over 0.4m/sec, and the width of net mouth showed about 37% of the distance between the fore tips of net pendant. The shape of net mouth was almost a circle at 0.2m/sec and then steeply flatted elliptically with the flow velocity increasing and the area of mouth S(m super(2)) can be expressed in S=(1.65-2.3v)$\times$10 super(-2). The hydrodynamic resistance of the net increased almost linearly with the flow velocity increasing and the resistance R(kg) can be expressed in R=3.2$\times$d/l$\times$abv. where d/l denotes the mean of d(diameter of netting twine) and l(length of a leg in a mesh) from wing tip to the end of bag-net except cod-end on the side pannel, and a denotes the strectched circumference of the net at the fore end of a meshed part and b the stretched length of the whole net from wing tip to the end of cod-end. 2. In the condition-varied nets, the vertical opening of head rope showed some increase in every type net except the C type, and the increase showed the greatest in the B type by 30~54%, whereas it showed decrease in the C type by 5~10%. Variation of the area of net mouth showed almost the same tendency as the vertical opening and the increase showed the greatest in the B type by 20%, whereas it showed decrease in the C type by 12%. Hydrodynamic resistance showed some increase in every type compared with the standard net, and the rate of increase indicated 5~10% in the A-2, A-3 and A-4 type, 22% in the B type and 3% in the C type.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.4 no.3_4
• /
• pp.79-91
• /
• 1971

A boat seine has been used as a major fishing gear for catching anchovy (Engraulis japonica) in the southern coastal waters of Korea since 1920s. The original seine was operated by two rowing boats as the haul seine. The rowing boats were, in recent, replaced by powered boats. The net size was enlarged by more than three times the original nit as they began to by operated in the deeper waters of approximately sixty meters. However, there are many problems in the efficiency of the fishing gear to be improved. The authors studied on the hydrodynamic resistance and performance of the boat seine net of the 1/10 scale model in tow. The results are summaried as follows. 1. The hydrodynamic resistance converted from model experiment into the full scale is: $$R_1=30,000\;v^{1.2}\;(0.2{\leqq}v{\leqq}1.0)$$ $$R_2=16,000\;v^2\;(0.2{\leqq}v{\leqq}0.6)$$ where $R_1$ and $R_2$ denote the resistance of whole gear and of bag net in kg respectively, and v the speed of flow in m/sec. 2. In the extension wing, approximately seventy percent of the length of the ground rope from the towing end to the inside-wing slopes down from sea level toward the sea bottom, while the thirty percent of the inside of it remains parallel with th: 5:a level. The performance is regarded to b: inefficient for driving fish shoal into the inside-wing, especially for the shoal diving suddenly. 3. At the towing speed higher than 0.2 m/sec, the trailing edge of the inside-wing is blown backward beyond the seaming line connecting the inside-wing and the mouth of the bag net. It is regarded as an unreasonable performance to drive the fish shoal smoothly into the bag net. 4. At the towing speed higher than 0.2 m/sec, the posterior end of the lower bosom is lifted up above the level of the ground rope of the inside-wing. It is considered that the fish shoal diving suddenly can escape through the discrepancy between the lower bosom and the sea bottom, even if the ground rope of the inside-wing sweeps the sea bottom. 5. The angle of inclination of the upper bosom is estimated as $35\~40^{\circ}$. It seems that the inclination is too steep to drive smoothly the fish shoal diving toward the sea bottom into the bag net. 6. In structure, circumference of the posterior section of the bag net is wider by 1.3 times that of the anterior section. Actually in towing at a speed higher than 0.2m/sec, however, the circumference of the posterior section becomes smaller than that of the anterior section. It is recommended to be designed in a long cylindrical form.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.15 no.2
• /
• pp.83-94
• /
• 1979

It is more than half a century since anchovy boat seine has been introduced in Korean fishery to catch anchovies, but the study on it was began in 1970's by the authors. In 1971, the authors carried out an experiment about the net formation of the traditional gear in tow by using model net, and in 1978, about the patti net gear, commercially used in Japan. Now, the authors investigated the new model net, model 79, expecting to be suitable for commercial fishery in Korea, with the strong point of those two gears kept and the weak point of them corrected. The experimental gear was constructed attached the long net pendants to the fore end of extension wing by shortening its length in two-third of the traditional gear. Inside wing was improved so as to show high opening in tow. Rubber bobbins and hanging rings are used to prevent the heavy friction of bosom ground rope against the sea bed. The gear was used to catch anchovies in the commercial fishing ground in the south-eastern coastal waters of Korea, from May to October in 1979. From the experiment, the following results are found. 1. In opening height, the experimented gear was 30 percent greater than the traditional one. 2. It took 3 to 5 minutes for the bosom ground rope to sink from the surface to the sea bed, while 10 to 15 minutes for the traditional gear to do. 3. Ground rope never scooped mud, even in the muddy sea bed. 4. The gear showed better catchability than the traditional gear.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.39 no.3
• /
• pp.189-196
• /
• 2003

In this study, the vertical opening of the non-float midwater pair trawl net was maintained by controlling the length of upper warp. This was because the head rope was able to be kept linearly and the working depth was not nearly as changed with the variation of flow speed as former experiments in this series of studies have demonstrated. We confirmed that the opening efficiency of the non-float midwater pair trawl net was able to be developed according to the increase in front weight and wing-end weight. In this study, we described the opening efficiency of the non-float midwater pair trawl net according to the variation of front weight and wing-end weight obtained by model experiment in circulation water channel. We compared the opening efficiency of the proto type with that of the non-float type. The results obtained can be summarized as follows：1. The hydrodynamic resistance was almost increased linearly in proportion to the flow speed and was increased in accordance with the increase in front weight and wing-end weight. The increasing rate of hydrodynamic resistance was displayed as an increasing tendency in accordance with the increase in flow speed. 2. The net height of the non-float type was almost decreased linearly in accordance with the increase in flow speed. As the reduced rate of the net height of the non-float type was smaller than that of the net height of the proto type against increase of flow speed, the net height of the non-float type was bigger than that of the proto type over 4.0 knot. The net width of the non-float type was about 10 m bigger than that of the proto type and the change rate of net width varied by no more than 2 m according to the variation of the front weight and wing-end weight. 3. The mouth area of the non-float type was maximized at 1.75 ton of the front weight and 1.11 ton of the wing-end weight, and was smaller than that of the proto type at 2.0∼3.0 knot, but was bigger than that of the proto type at 4.0∼5.0 knot. 4. The filtering volume was maximized at 3.0 knot in the proto type and at 4.0 knot in the non-float type. The optimal front weight was 1.40 ton.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.37 no.2
• /
• pp.78-84
• /
• 2001

Escape behaviour of the anchovy (Engralius japonica, total length 4-7cm) at the inside wing net and bag net in the anchovy boat seine was observed by underwater video camera in order to clarify the relationship between visual stimulus of the gear or relative water flow inside gear and reacting behaviour. The vertical attenuation coefficient of underwater illuminance in the offshore of Keoje island and Tongyoung was ranged from 0.24 to 1.03 and it could be affect visual range and visual contrast of the fishing gear. The relative water flow at the joint part between inside wing and bagnet while towing was 1.5 times higher than at the middle part of inside wing or fore part of bag net, but it was estimated under than maximum swimming speed of 4-7 cm anchovy. The mean escaping number of anchovy from end part of inside wing of 30 cm mesh to out side for a minute within visual range of video camera was 455 and anchovy swimming forward from bag net through flapper was 308. These results revealed anchovy could escape as voluntary response in spite of higher visual stimulus or higher water flow.