• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.6
• /
• pp.134-140
• /
• 2003

The film sensor is used for measuring pressure distribution at planar area, especially at a small space or gap. The present paper deals with the development of film type sensors and system for pressure distribution measuring. The developed system is consist of (1)film sensor with 40/sup */40 array, (2)PCI interface card with maximum sampling rate of 100㎐, and (3)software for data processing and real-time display. The contact pressure test of wiper blade and front glass of vehicle was performed with wiper blade by 40cm. Generally spring force of wiper arm is designed at 0.7∼1kN. Test results of total force was 9.4N and 7.1N in each driver and passenger toward. The paper suggested possibility for base definition in wiper design. A windshield wiper blade experiment revealed that the system successfully measured the contact force distribution during static state, showing the usefulness of the developed system.

• Journal of KSNVE
• /
• v.8 no.5
• /
• pp.862-869
• /
• 1998

The interior noise generated by the windshield wiper system including a wiper motor, the motor mountings and linkages is considered as a structure-borne noise. The structureborne noise is closely related with the system vibration which was transmitted into interior cabin through the car body. In this study, the frequency characteristics of vibration in the wiper motor system were first identified through the frequency analysis. Then effects of the wiper motor mountings and linkages on the vehicle interior noise were studied through in-vehicle measurements. Finally a possibility of noise reduction at a certain frequency was revealed from the study.

• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.7
• /
• pp.649-657
• /
• 2004

A windshield wiper system plays a key part in assurance of driver's safety at rainfall. However, because quantity of rain and snow vary irregularly according to time and velocity of automotive, a driver changes speed and operation period of a wiper from time to time in order to secure enough visual field in the traditional windshield wiper system. Because a manual operation of wiper distracts driver's sensitivity and causes inadvertent driving, this is becoming direct cause of traffic accident. Therefore, this paper presents the basic architecture of vision-based smart wiper system and the rain sensing algorithm that regulate speed and interval of wiper automatically according to quantity of rain or snow. Also, this paper introduces the fuzzy wiper control algorithm based on human's expertise, and evaluates performance of suggested algorithm in the simulator model. Especially the vision sensor can measure wider area relatively than the optical rain sensor, hence, this grasps rainfall state more exactly in case disturbance occurs.

• Proceedings of the Korean Reliability Society Conference
• /
• 2011.06a
• /
• pp.107-113
• /
• 2011

The windshield wiper consists of 4 parts: a blade, an arm, a linkage and a motor. The wiper blade makes contact with the windshield and is designed to be operated normally at an angle of 30~50 degrees to the front glass. If the contact pressure between the wiper blade and windshield surface is too high, noise and wear of the rubber will result. On the other hand, if the contact pressure is too low, the performance will do badly, since foreign substances such as dust and stains will not be removed well. The pressure and friction of the wiper blade has a great influence on its effectiveness in cleaning the front window. This is due to the contact of the rubber with the window. This paper presents the dynamic analysis method to estimate the performance of the flat type blade of the wiper system. The blade has a nonlinear characteristic since the rubber is an incompressible hyper-elastic and visco-elastic material. Thus, Structural dynamic analysis using a complex contact model for the blade is performed to find the characteristics of the blade. The flexible multi-body dynamic model is verified by the comparison between test and analysis result. Also, the optimization using the central composite design table is performed.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.10
• /
• pp.974-984
• /
• 2012

This research introduces a new method to attenuate flip-over vibration generation in the flat blade windshield wiper by adjusting the contact pressure between the windshield glass and the blade. The knocking force in the flip-over action of the blade is decreased by inducing gradual tilting-over along the rubber strip of the blade. This gradual tilting-over is induced by introducing a non-uniform contact pressure distribution between the blade and windshield glass. The contact pressure distribution is adjusted by controlling the unloaded profile of the body spring in the blade using a procedure proposed in a previous study. Two blades, one blade designed to generate a uniform pressure distribution and the other designed to generate non-uniform pressure distribution, are developed using the procedure. Contact pressure distributions of the developed blades are measured using a special device and compared with the intended distributions confirming the similarities between the two groups. Vertical and lateral vibrations of the two blades are measured under realistic operating condition simulated by a wiper test rig. The vertical vibrations of the blade with non-uniform contact pressure are substantially smaller than corresponding vibrations of the blade with uniform contact pressure over the entire rubber strip.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.2
• /
• pp.83-90
• /
• 2010

The windshield wiper consists of 4 parts: a blade, an arm, a linkage and a motor. The wiper blade makes contact with the windshield and is designed to be operated normally at an angle of 30~50 degrees to the front glass. If the contact pressure between the wiper blade and windshield surface is too high, noise and wear of the rubber will result. On the other hand, if the contact pressure is too low, the performance will do badly, since foreign substances such as dust and stains will not be removed well. The pressure and friction of the wiper blade has a great influence on its effectiveness in cleaning the front window. This is due to the contact of the rubber with the window. This paper presents the dynamic analysis method to estimate the performance of the flat type blade of the wiper system. The blade has a nonlinear characteristic since the rubber is an incompressible hyper-elastic and visco-elastic material. Thus, Structural dynamic analysis using a complex contact model for the blade is performed to find the characteristics of the blade. The flexible multi-body dynamic model is verified by the comparison between test and analysis result. Also, the optimization using the central composite design table is performed.

• Elastomers and Composites
• /
• v.55 no.3
• /
• pp.229-234
• /
• 2020

Automobile wiper blades are generally treated with chlorine to lower their friction coefficient with the windshield surface. This treatment could affect the crosslink density measurement of rubber vulcanizates, a material used in windshield wipers, which would consequently alter its chemical and physical properties. Therefore, this study evaluated the influence of chlorination on crosslink density measurements of natural rubber (NR) vulcanizates using a vehicle wiper blade. A method for determining the degree of chlorination was developed where the interaction parameter between the rubber and the swelling solvent was corrected. A decrease in the rubber sample swelling ratio was observed upon chlorination, and the chlorination penetrated less than 1% of the sample thickness. The chlorinated NR was assumed to be chloroprene rubber (CR), which was used to correct the interaction parameter. The results showed the CR contributed approximately 7% to the parameter.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.3
• /
• pp.292-298
• /
• 2015

A wiper is a safety device removing rain and debris from windshield and ensuring visibility of drivers. If contact pressure distribution between rubber of the blade and the windshield is unbalanced, unwanted noise, vibration, and abrasion of the blade can occur and sometimes fatal accidents could occur. To improve the safety of the wiper, there have been many researches on the contact pressure analysis of the wiper, but the analysis results were not converged or require much computational time due to material nonlinearity of the rubber and contact conditions between the blade rubber and the windshield. In this research, a simple model with 1D beam and 2D shell elements was used for the contact pressure analysis instead of the 3D blade model. The simplified model saved computational time of the analysis and resolved convergence problems. The accuracy of the analysis results was verified by comparing them with experimental results for different rail spring curvatures.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.2
• /
• pp.210-215
• /
• 2001

The pole antenna of vehicles for AM/FM radio broadcasting receptions has many probems, such as damageable mechanical system and noise etc. It is considered that noise is composed of the structural vibration noise and the air flow induced aerodynamic noise. Also we find out that the setting process of a printed on-glass automobile antenna has many difficulties. Recently, the above mentioned problems can be reduced by employing enhanced wiper antenna which utilizes the windshied wiper arm. The new system is a passive antenna. In this study, experiments for the characteristics of a wiper antenna by measuring the SWR, radiation pattern and received powe have been carried out. The experimental results show that the efficiency of the wiper antenna has better performance than any other antenna.

• Elastomers and Composites
• /
• v.55 no.4
• /
• pp.257-262
• /
• 2020

Vehicle wiper blades are typically treated with chlorine to lower their friction coefficient with the windshield surface. In this study, a chlorinated, natural rubber (NR) vehicle wiper blade was characterized using a pyrolytic technique. Unchlorinated and chlorinated wiper blades were pyrolyzed and the pyrolysis products were analyzed using gas chromatography/mass spectrometry (GC/MS). Besides isoprene and dipentene, the other principal pyrolysis products such as 1,5,8-p-menthatriene (MTT) and p,α-dimethylstyrene (DMS) were observed. The MTT and DMS ratios did not vary for the chlorinated nor unchlorinated samples when the entire rubber lip of the wiper blade was pyrolyzed. However, when only the lip surface of the wiper blade rubber was pyrolyzed (via scratching with a knife) the relative ratios of the chlorinated sample were much greater than those of the unchlorinated sample. As MTT is produced from the conjugated backbone of chlorinated NR that forms through HCl elimination during initial pyrolysis, and DMS is generated by the dehydrogenation of MTT, these two products could be used as markers for detecting chlorinated NR.