• Journal of Advanced Marine Engineering and Technology
• /
• v.26 no.4
• /
• pp.464-471
• /
• 2002

Porosity formation in partial penetration welds by high power lasers is a serious problem in industry. There are two main causes that induce porosity formation. One form of porosity is due to gases (e.g. hydrogen, oxygen) dissolving into the weld pool because of the high temperature and then the rapid solidification traps gases as a bubble in the weld metal. The second problem is voids formed by the keyhole collapsing due to unstable keyhole fluid dynamics. The voids that form at the bottom of the keyhole are relatively large and irregular in shape compared to the gas bubbles; this void formation is the primary concern in this paper. The reduction of voids formed by keyhole collapse is achieved by improving the stability of keyhole. Two methods to improve keyhole stability are discussed in this paper: pulse modulation and beam incident angle. Pulse modulation of the laser beam was performed between 100 Hz and 500 Hz to find out the optimum frequency for the keyhole dynamics. The incident beam angle changed the impact angle of the laser beam to the work surface in a range of 0 to 25 degrees. Glycerin in a semi-solidified state is used as a medium for performing the welding because its transparency allows of visualization of the keyhole.

• Explosives and Blasting
• /
• v.28 no.2
• /
• pp.50-58
• /
• 2010

This study explores the slot-drilling method that has not yet enough been studied in Korea and intends to provide a theoretical framework for putting the method into practice in a construction site. The possible reduction of ground vibration by implementing slot-drilling methods is addressed. Two main subjects dealt with include the variation of vibration velocity that is based on the distance between the slot-drilling and the epicenter of blasting and the analysis of appropriate effective dimension of slot-drilling width and height to control blasting vibration. This study shows that effect of vibration reduction decreases when distance of the slot-drilling and the epicenter of blasting is getting larger and also reveals that there is a correlation between the slot size and the vibration velocity at any point.

• The Journal of Korean Academy of Orthopedic Manual Physical Therapy
• /
• v.1 no.1
• /
• pp.75-83
• /
• 1995

Traction is the treatment of choice for a small nuclear protrusion. The nucleus is soft and can be influenced by suction. Traction provides a method of improving on recumbency-the only effective treatment before traction was devised. The intention is to achieve rapid reduction by distraction the joint surfaces mechanically-a positive purpose-instead of merely avoiding the compression of the upright posture by putting the patient to bed and leaving him there. Recumbency, usually successful in the end, wastes an endless amount of the patient's time and money. Traction carries the further advantage of enabling the patient to be up and about, attending to his bussiness, during treatment. Traction brings the joint surfaces much farther apart than just lying in bed, a greater centripetal force acts on the protruded part of the nucleus. Traction has three beneficial effects; 1. Suction : a sub-atmospheric pressure induces a centripetal effect on the contents. 2. Distraction : increases the distance between the articular edges. X -rays have shown an increase in width of the joint of 2.5 mm. 3. Ligamentous tightening : the posterior longitudinal ligament tightens which then exerts centipetal force on a central protrusion.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.6
• /
• pp.954-959
• /
• 2015

In this paper, 110kW high output density, high efficiency Permanent Magnet Synchronous Motor which can be applied on tram’s traction system is introduced, along with its output and loss characteristics. The motor model is 2pole 18slot model and its size has been reduced through the high speed for high output density. Especially, structure and retainer sleeve structure is applied to its structure, which is also appropriate for high speed rotation. This kind of structure has eddy current loss problem on the surface of rotor, which must be reduced for high output density design. This study has designed the most optimized additional design parameter in order to improve the output characteristics and efficiency of previous produced 2pole 18 slot 110kW motor model and how the width of airgap affects from the loss perspective is mainly analyzed. Finally, the analysis on the extent of the efficiency improvement effect compared to the previous model has performed through electromagnetic FEM analysis. The influence of airgap flux density distribution has also been thoroughly examined.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.3
• /
• pp.56-61
• /
• 2007

In this paper, a circulating current reduction approach for the parallel operation of fuelcell systems with Z-source inverters is investigated. The carrier phase shifted SPWM(Sinusoidal Pulse Width Modulation) is used as a modulation method since it has an advantage in reducing output current harmonics. However, when this technique is applied to the parallel operation of Z-source inverters, it additionally produces circulating currents. A coupled circulating current reactor is used to reduce circulating current generated by the parallel operation of Z-source inverters and to reduce output current harmonics. The proposed circulating current reduction approach using coupled circulating current reactors is verified through simulation and experiment.

• Steel and Composite Structures
• /
• v.8 no.3
• /
• pp.179-200
• /
• 2008

This paper reports the results of a recent experimental study into the behavior of welded fin-plate connections to both hollow and concrete filled tubular (CFT) columns under shear. Experiments have been performed at both ambient and elevated temperatures with the aid of an electric kiln. The observed failure modes include fracture of the fin plate and tearing out of the tube around the welds. By considering the results of previously published research, the current design method for similar connections under purely tensile load, in CIDECT Guide 9, based on a deformation limit of 3% of the tube width is shown to be inadequate when evaluating the ultimate strength of such connections. By comparing the results from the current test program which failed in the fin-plate with Eurocode guidance for failure of a fin-plate alone under shear and bending load it is shown that the column face influences the overall connection strength regardless of failure mode. Concrete in-fill is observed to significantly increase the strength of connections over empty specimens, and circular column specimens were observed to exhibit greater strength than similarly proportioned square columns. A finite element (F.E.) model, developed using ABAQUS, is presented and validated against the experimental results in order that extensive parametric tests may be subsequently performed. When validating the model against elevated temperature tests it was found that using reduction factors suggested in published research for the specific steel grades improved results over applying the generic Eurocode elevated temperature steel strength reduction factors.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.11a
• /
• pp.61-65
• /
• 2005

Existing test methods for thick-section specimens ( 4mm) have not provided precise compressive properties to date for the analysis and design of thick structure. A survey of the failure behaviour of such thick specimens revealed that the failure initiated at the top corner of the specimen and propagated down and across the width of the specimen as premature failure, not typically reported for thin compression specimens. In the current study, the premature failure was successfully avoided during compressive testing and the failure mode was quite similar regardless of increasing specimen thickness and specimen volume. Failure mode was similar regardless of increasing specimen thickness and specimen volume, i.e. brooming failure mode combined with longitudinal splitting, interlaminar cracking, fibre breakage and kinkband formation (fibre microbuckling). Nevertheless, average failure strengths of the specimens decreased with increasing specimen thicnkiness from 2mm to 8mm with the T800/924C system (36% strength reduction) and specimen volumes from scaling factor I to scaling factor 4 with the IM7/8552 system (46% strength reduction). It was revealed from the literature$^{11}$ that the thickness effect and scaling effect arc caused by manufacturing defects such as void content and fibre waviness.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.9
• /
• pp.1095-1104
• /
• 1997

When a high-speed railway train enters a tunnel, a compression wave is generated ahead of the train and propagates along the tunnel, compressing and accelerating the rest air in front of the wave. At the exit of the tunnel, an impulsive wave is emitted outward toward the surrounding, which causes a positive impulsive noise like a kind of sonic boom produced by a supersonic aircraft. With the advent of high-speed train, such an impulsive noise can be large enough to cause the noise problem, unless some attempts are made to alleviate its pressure levels. For the purpose of the impulsive noise reduction, the present study investigated the effect of a vertical bleed duct on the compression wave propagating into a model tunnel. Numerical results were obtained using a Piecewise Linear Method and testified by experiment of shock tube with an open end. The results showed that the vertical bleed duct reduces the maximum pressure gradient of compression wave front by about 30 percent, compared with the straight tunnel without the bleed duct. As the width of the vertical bleed duct becomes larger, reduction of the impulsive noise is expected to be greater. However the impulsive noise is independent of the height of the vertical bleed duct.

• The Journal of the Acoustical Society of Korea
• /
• v.35 no.5
• /
• pp.349-357
• /
• 2016

In this work, we proposed various structural methods to reduce the crosstalk between elements in a planar array of underwater acoustic transducers and investigated the efficacy of each method through finite element analysis. It is shown that the effects of crosstalk reduction increase as the depth of the kerf among elements and the width of the kerf increase, and the elastic stiffness of the kerf filler decreases. Results of this study are expected to be useful in designing the structure of underwater acoustic planar array transducers to maximize their performance.

• Journal of the Korean Society for Railway
• /
• v.8 no.5
• /
• pp.454-459
• /
• 2005

In this study, the relationship between tie shape and underbody train gust of high-speed train is numerically investigated. To this end, complex train underbody/railroad model is replaced by simple plate/tie model. And it is tried to find a most important parameter for reduction of underbody train gust through the Taguchi method and orthogonal array. As a result, it is verified that the height of tie is most sensitive to the underbody train gust because of the cavity effect between ties. When the width and distance between ties are decreased, underbody train gust is also reduced. Consequently, the heighter is examined which can give the similar effect of higher tie without replacement of tie. The 5cm heighter can reduce underbody train gust about $73\%$, which value is only $7\%$ less than the higher tie.