• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 제3회 압연심포지엄 논문집 압연기술의 미래개척 (Exploitation of Future Rolling Technologies)
• /
• pp.423-428
• /
• 1999

A high precision hot strip width control method has been developed in this study by applying interstand looper tension measuring system at finishing mill stands. As with deviation of hot rolled steel strip is closely related to abnormal increase in the interstand strip tension, on-line measuring device of looped tension and data analyzing system was developed in this study. To determine dominant factors that will cause local width shortage, the logged data sets of bar width, bar thickness, looper tension, and strip thickness along the strip length were correlated with the data set of strip width change. With the result of the correlation analysis, existing sequence control logic and parameters for looper actuator were modified for strip width quality and the gains of the looper control were refined for the stable operation during the full passage of rolled strip. The on-line tension measurement and tension feedback control for looper system improved strip travelling stability and reduced strip width deviation in the srip top end region.

• 대한기계학회논문집A
• /
• 제23권7호
• /
• pp.1196-1204
• /
• 1999

adaption of the model predictions is highly desirable. In general, the width deviation at the head and tail ends of strip may be different from that of the steady state region. Therefore, the dynamic edger corrections can be used to compensate the width deviations which would otherwise occur. For the precise width control, the effect of edger roll gap and rolling conditions on the width deviation of head and tail ends of strip has been investigated and the effective method to decrease width deviation has been proposed. On-line application of dynamic edger control method in this study shows about 50% width compensation at the head end of the strip, and near perfect compensation at the tail end of strip.

• 센서학회지
• /
• 제19권5호
• /
• pp.391-397
• /
• 2010

This paper proposes a differential structure sensor for detecting Ringer's solution exhaustion, in which three C-type electrodes of 10 mm width are disposed on a ringer hose at a distance of 5 mm each other in the direction of Ringer's solution flow. In the center of middle electrode, two capacitances are formed at the proposed sensor. When ringer hose is filled with Ringer's solution, there is no difference between two capacitances. But capacitance difference exist under the Ringer's solution shortage, because the shortage causes the hose filled with air from the top position electrode. The capacitance difference got to maximum 1.81 pF, when air was filled between top and middle electrode and the last of hose was filled with 10 % dextrose injection Ringer's solution. The capacitance difference varied with hose-wraparound coverage of electrodes as well as the width of them. For hose-wraparound electrode coverage of 90 % and 70 %, the maximum capacitance difference was 1.81 pF and 1.56 pF, respectively. A differential charge amplifier converted the capacitance difference to electric signal, and minimized electrodes' adhering problem and external noise coupling problem.

• 대한기계학회논문집
• /
• 제16권7호
• /
• pp.1278-1284
• /
• 1992

본 연구에서는 무전단 후판압연기술을 위한 요소기술로써 지난호에 게재한 오버랩연구에 이어 모델압연 실험과 유한요소 해석을 이용한 에징시 비정상부의 폭변 형거동에 대한 연구결과를 보고한다.

• 콘크리트학회지
• /
• 제6권2호
• /
• pp.169-179
• /
• 1994

주택건설은 극심한 건축자재 부족과 인력수급등의 많은 어려움을 격고 있는데, 이에 대한 문제의 해결방은 중 하나로 철근콘크리트 공사에서 철근의 가공조립공정을 보다 간소화하면서 그 기능의 효율성을 높이는 방법으로 구조용 용접철망과 루프형 용접철망을 이용한 공법이 제기되고 있다. 본 연구에서는 일방향 슬래브에 콘크리트 예상 압축강도가 $210kg/cm^2$일 때, 최대균열폭과 소성변형 능력에 영향을 미치는 요인인 사용철근의 종류, 최소철근비를 기준으로 한 인장철근비(${\rho}t$), 주변지지조건, 겹이음길이의 4가지 주요변수로 하여 슬래브의 구조적 특성 및 휨거동을 파악하는데 그 목적을 두었다. 연구결과, 소성변형능력은 이형철근을 사용한 슬래브가 용접철망을 사용한 슬래브보다 월등히 큰 것으로 나타났고, 겹이음된 슬래브에서는 겹이음길이 30D가 적절한 것으로 나타났다. 또한 최대균열폭은 용접철망과 루프형 용접철망을 사용한 슬래브가 이형철근을 사용한 슬래브 보다 균열폭을 억제하는 것으로 나타났다.

• 한국가시화정보학회지
• /
• 제9권1호
• /
• pp.29-35
• /
• 2011

In this paper, we applied various microfluidic chambers to visualize cell migration and measured the migration velocity in microchannels. Migration speed of B16 cell in a large channel was similar with that of wound healing experiment. However, the speed decreased gradually as the cell move inside of the channel. It is expected that this phenomenon is due to the shortage of oxygen or nutrition, whichare essential for cell growth. In the case of cell in the small channel whose size is smaller than the cell, its speed was slower than that in a larger channel.

• 한국연초학회지
• /
• 제15권1호
• /
• pp.57-62
• /
• 1993

Ridger and vinyl mulcher for 8-10 PS power tiller which were distributed at the rate of one out of 2.3 farm households in Korea, was developed to ease the labor shortage of tobacco production. Devices wheel shaft extension by 30cm at both sides improved the stability of straight drive and enabled to save required labor hours by 50% for ridging at sloping field. Screw type blades were attached on center drive rotavator shaft, gear set was deviled to reverse the rotavator, and it was good at need to adjust the width and height for ridge. As the results, required labor hours for ridging and vinyl mulching could be saved by 90% as compared to conventional manual method after cattle plowing, and by 50% as compared to conventional power tiller method.

• 건축역사연구
• /
• 제30권1호
• /
• pp.7-17
• /
• 2021

Bang walls surround the four sides of Band in ancient capital cities of East Asia where the Bang system was in operation. There are ongoing research efforts for the structure of a capital city and Bang system around the capital of Silla, but there is a huge shortage of research on Bang walls. This study thus set out to examine Bang walls in the capital of Silla around the Hwangnyongsa Temple and its surroundings. The findings show that the Bang walls in the capital of Silla were built with a mix of earth and stone and with tiled roofs on top. The sizes of Bang walls were distinguished from the walls of individual structure groups inside Bang and closely related to the Bang size and the width of adjacent roads.

• 제어로봇시스템학회논문지
• /
• 제6권8호
• /
• pp.638-651
• /
• 2000

When the bandwidth resources in a packet-switched network are shared among sessions by MAX-MIN flow control each session is required to transmit its data into the network subject to the MAX-MIN fair rate which is solely determined by network loadings. This passive behavior of sessions if fact can cause seri-ous QoS(Quality of Service) degradation particularly for real-time multimedia sessions such as video since the rate allocated by the network can mismatch with what is demanded by each session for its QoS. In order to alleviate this problem we extend the concept of MAX-MIN fair bandwidth allocations as follows: Individual bandwidth demands are guaranteed if the network can accommodate them and only the residual network band-width is shared in the MAX-MIN fair sense. On the other hand if sum of the individual bandwidth demands exceeds the network capacity the shortage of the bandwidth is shared by all the sessions by reducing each bandwidth guarantee by the MAX-MIN fair division of the shortage. we present a novel flow control algorithm to achieve this extended MAX-MIN fairness and show that this algorithm can be implemented by the existing ATM ABR service protocol with minor changes. We not only analyze the steady state asymptotic stability and convergence rate of the algorithm by appealing to control theories but also verify its practical performance through simulations in a variety of network scenarios.

• 한국작물학회:학술대회논문집
• /
• 한국작물학회 2022년도 추계학술대회
• /
• pp.279-279
• /
• 2022

Rice is 34% of the world's population used as a staple food. But the world population is increasing. Food security is not well protected. Improving cultivar development can address food security. Quantitative trait locus (QTL) mapping is a statistical analysis using both phenotypic and genotypic dates. The purpose of QTL mapping is to determine a gene. Increasing grain size is a way to increase yield in rice. Grain size-related genes were mapped using CNDH population obtained by cross-breeding Cheongcheong (Indica) and Nagdong (Japonica) through anther culture. Grain harvested from experimental field of Kyungpook National University in Gunwi in 2021. Genes related to grain length were detected between RM5964-RM12285, RM20924-RM20967 in chromosome 1, 7. LOD score is 5.88 and 5.6. Genes related to grain width was detected between RM289-RM18130 in chromosome 5. LOD score is 4.57. Genes related to grain length/width ratio were detected between RM5459-RM3482, RM5699-RM1211 and RM3838-RM3381 in chromosome 1, 2, 5. LOD score is 3.75, 3.14 and 3.41. 4 genes was detected in chromosome 1 and 2 genes was detected in chromosome 2 and 7 genes was detected in chromosome 5. 2 genes related to grain shape and quality were detected. 4 genes related to grain length were detected. 4 genes related to grain size were detected. 1 gene related to grain size and weight was detected. 2 genes related to grain length and weight were detected. By finding the gene related to grain size, it provides food to people threatened by food security and solves the food shortage.