• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2018.05a
• /
• pp.441-444
• /
• 2018

In this paper, a microstrip antenna for LTE / WiMAX is designed for UWB communication. The proposed antenna is designed for FR-4 (er = 4.3), 29[mm] x 45[mm], and can be used in the LTE frequency band of 1.82[GHz] and the WiMAX frequency band of 3.5[GHz]. Studio 2014 was used. The simulation results show 1.785[dB] at 1.82[GHz] and 1.720[dB] at 3.5[GHz]. S-parameters were also found to be less than -10dB (WSWR2: 1) in the desired frequency band. In order to achieve broadband, miniaturization, low cost and low loss, Width, length, width of transmission line, etc. were calculated. Therefore, it is considered that the applicable antenna can be applied satisfying the desired condition.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.8 no.6
• /
• pp.88-97
• /
• 2009

As the development of wireless techniques, transmission technology of body area network plays an important role in realizing a welfare society by combining IT and BT when applying to vehicles. Off-body WBAN (Wireless Body Area Network) systems for video data transmission require low battery consumption and high data rate. To satisfy the requirement, UWB has been considered as a promising candidate for high rate WBAN. This paper introduces an antenna selection technique for ultra-wideband based off-body WBAN system with low complexity. In this paper, we propose an antenna selection scheme using non-coherent receiver for off-body high data rate WBAN system. The proposed receiver antenna selection method takes advantage of the characteristic of BPPM (Binary Pulse Position Modulation). With the property of BPPM, this scheme calculates the approximate SNR of the received signal with non-coherent receiver.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.4
• /
• pp.387-392
• /
• 2014

In this paper, the broadband antenna design, which can be applied to USB Dongle, supporting Wibro(2.3~2.4 GHz), Wi-Fi(2.4~2.5 GHz) and LTE7(2.5~2.7 GHz) is proposed technique. The proposed antenna was designed similar to PIFA type antennas. Reactive elements were used to control the input impedance and wideband characteristics were achieved by controlling coupling between the feed structure and the radiator. As a result, the antenna printed on FR-4 PCB(${\epsilon}_r$ =4.4, tan ${\delta}$=0.02) occupying an area of $15{\times}5mm^2$ was able to achieve bandwidth of 1 GHz from 2.1 to 3.1 GHz under VSWR=2. Measured return loss characteristics, bandwidth and radiation patterns were in good agreement with the simulated results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.12 s.103
• /
• pp.1194-1205
• /
• 2005

This paper proposes a uni-planar elliptical element UWB antenna with band-notched characteristic and modified pound plane fed by CPW. The antenna achieves VSWR below 2 for UWB band(3.1 GHz${\~}$10.6 GHz). In addition, a band-notched characteristic is achieved by inserting a horizontal slot on the radiation element to avoid the interference with 5 GHz(5.15 GHz${\~}$5.825 GHz) band limited by IEEE 802.1la. The antenna has a thin profile, compact size, and ease of manufacture by adopting a CPW feed structure without any additional background plane. Measured data show that the proposed antenna has good return loss below -10 dB, about 2.1 dB${\~}$4.75 dB maximum gain over the bandwidth, omni-directional radiation patterns, linear phase response.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.37 no.2
• /
• pp.69-74
• /
• 2000

The bandwidth of microstrip slot antenna with T-shaped feed line was a wider than one of the conventional feeding structure. When the slot antenna with bi-directional radiator wants to radiate only one direction, the reflector must be set up seperately. But this antenna doesn't need set up reflector. And then we proposed to a new method of a directional slot radiator with a cross-shaped feedline including the reflector using 2-layers dielectric materials. It is calculated waves and electric field distribution in the time domain by using FDTD method. We also are calculated return loss, VSWR, input impedance, and radiation pattern in the frequency domain by Fourier transforming the time domain results, respectively. It was found that the bandwidth of this antenna changes as length($\I_s$) and width($\W_s$) of slot, length of the horizontal feedline($\I_d$), length of the vertical feedline($\I_u$) and offset sensitively. After optimizing the parameters of design, the maximum bandwidth was measured as 1,850MHz at the center frequency 2.5 GHz.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.2A
• /
• pp.195-201
• /
• 2004

In this paper, U-Shaped slot Bow-Tie antenna for 5.15㎓∼5.35㎓ is designed, fabricated, and measured. The prototype consist of U-Shaped slot. To obtain suitable bandwidth, the form layer is inserted between ground plane and substrate. Important parameters in the design are U-slot length, width, position, air-gap height, and feed point position. From these parameters optimized, a U-shaped slot Bow-Tie antenna is fabricated and measured. The measured results of the antenna are obtained as follows results. The resonant frequency of the Fabrication U-shaped slot Bow-Tie antenna is 5.28㎓, bandwidth for approximately 7.76％(VSWR<1.2) and the gain is 4∼7dBi. The experimental far-field patterns are stable across the pass band. The 3dB bandwidth in Elevation and Azimuth are 73.63$^{\circ}$and 65.08$^{\circ}$, respectively.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.11
• /
• pp.2518-2525
• /
• 2015

In this paper, we propose a UWB(Ultra Wide Band) antenna with CPW(Coplanar Waveguide) structure notched the 802.11a(5.15 ~ 5.825 GHz) band by using the U shaped slot. The proposed antenna not only shows Ultra-Wideband characteristic(3.1 ~ 10.6 GHz) suitable for UWB communications but has partially notched-band characteristic to reject 5 GHz WLAN band(5.15 ~ 5.825 GHz). The antenna is designed on an FR-4 substrate of which the dielectric constant is 4.4, and its overall size is $30mm(W){\times}20mm(L){\times}1mm(t)$. Fabricated antenna satisfied $VSWR{\leq}2$ in 3.1 ~ 10.6 GHz except for the band rejection of 5.15 ~ 5.825 GHz. And measured results of gain and radiation patterns characteristics displayed determined for operating bands.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.1
• /
• pp.23-32
• /
• 2008

In the VHF range, active antennas are widely used for wideband applications due to their small size. Active antenna consists of antenna elements and amplifiers, which are directly connected to each other. Gain and noise-figure characteristics are very important for good sensitivity performance, because it is located at the front end of a receiving system. In this study, we developed an active dipole antenna with 5:1 bandwidth(100${\sim}$500 MHz), which consists of a dipole antenna and a P-HEMT amplifier. To obtain required performances, the antenna and the amplifier should be designed simultaneously. In order for that, we introduced an equivalent port concept to model the 1-port dipole antenna as an equivalent 2-port system. Using the proposed equivalent port, the performance of the active dipole antenna was simulated by the ADS. In order to measure the gain and noise-figure characteristics of the antenna, we utilized the same concept of the two-port equivalent impedance model. The measurement results for typical gain, NF and VSWR in the required frequency band were 8dBi, 9dB and 1.7:1, respectively. The radiation patterns at the principal planes were same as the typical radiation pattern of a dipole antenna. By comparing the simulation results with measured ones, it is confirmed that the proposed methods works well.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.8
• /
• pp.308-315
• /
• 2013

In this paper, Tapered slot antenna of IR-UWB was Designed and fabricated using HFSS and we suggest the beam width of the broadband antenna using group-delay and fidelity. For this purpose, acquired data from the Network Analyzer was analyzed in the time domain by using the chirp-Z transform and Simulation was conducted and confirmed with the CST microwave studio. Analysis of the antenna radiation pattern is the antenna separation at intervals of 0.5 metres and then transmit antenna is fixed and the receiving antenna 360 degree intervals of 10 degree each, The results of the analysis are as follows, and analyzer of the fidelity of the antenna's performance. An analysis of more than 90 percent of the cases is less than ${\pm}40$ degrees in good fidelity, more than 90% less than ${\pm}40$ degrees and lowe fidelity. In conclusion, Analysis of Beam width of wideband antenna with more precise is possible through using these radiation pattern using fidelity.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.4
• /
• pp.286-297
• /
• 2017

This paper is a study of 6~18 GHz wideband high power amplifier which is composed of 10 single amplifier and coaxial type spatial power combiner. The property of this spatial power combiner is on a similar principle to antipodal antenna radiation mechanism. Therefore, the key structure of proposed spatial power combiner is the antipodal finline PCB board and the finline curve shape is numerically synthesized by using Klopfensein's optimum impedance taper. The measured CW output power of spatial combined high power amplifier is nearly 50 W. In conclusion we prove the good combining performance between the spatial power combiner and 10 single amplifier over 6~18 GHz frequency ranges. Also, we developed the key component PA and MFC MMIC which controls the phase and gain of the each amplifier, The main characteristic of MFC MMIC is to maximize combining efficiency of power amplifier.