• 한국전산구조공학회논문집
• /
• 제29권3호
• /
• pp.285-292
• /
• 2016

본 연구에서는 부유구조물 모델링의 효율성 및 응답의 정확성을 분석하기 위해 유체 영역을 압력으로 정의한 유탄성 해석법에 1차원 보-2차원 유체 결합의 1차원 문제와 2차원 판-3차원 유체 결합의 2차원 문제를 적용하여 수치해석을 수행하였다. 그리고 1차원 문제와 2차원 문제의 모델링 차원에 따른 응답을 비교하기 위해 다양한 평판의 변장비와 입사파의 조건을 적용하였다. 이에 따르면 강체거동의 영향이 큰 장주기파에서는 변장비가 변하더라도 두 문제의 유탄성 응답이 거의 유사하게 나타나지만 탄성거동의 영향이 지배적인 단주기파에서는 모델링 차원에 따라 뚜렷한 차이가 발생한다. 즉, 1차원 보 모델은 비록 입사파의 각도는 고려할 수 없지만 평판의 변장비가 클 경우에 유탄성 해석에 적용이 가능하다. 또한, 2차원 평판보다 단순화된 모델링 조건으로서 부유구조물의 전반적인 응답을 분석할 수 있을 뿐만 아니라 수치해석의 효율을 높일 수 있다.

• 콘크리트학회논문집
• /
• 제14권6호
• /
• pp.823-829
• /
• 2002

철근콘크리트 기둥-철골 보 합성골조는 철근콘크리트와 철골부재의 재료적인 장점을 살린 합리적인 구조물이나, 이질 재료간의 접합으로 인해 보-기둥 접합부의 설계와 해석에서는 많은 구조적인 문제점들이 생기게 된다. 이 연구에서는 철골 보의 하중이 콘크리트 기둥으로 원활히 전달되면서 현장 시공성이 우수한 새로운 형태의 합성골조 접합부의 형식을 제안하고자 한다. 이 연구에서 고안된 접합부는 H 형강을 반분한 T 형강을 시스템 내부 및 외부의 모든 응력 전달 요소를 연결하는 주요 요소로 하고, 보 플랜지의 인장력 전달을 위해 한 방향은 고강도 강봉을, 이와 직교하는 방향은 강재 연결판을 사용하였다. 스티프너보강된 ㄱ형강을 사용하여 보 플랜지의 인장력을 기둥면에 전달하도록 하였으며, T 형강에 용접된 전단 접합판을 보의 웨브와 고력볼트로 접합하여 전단력을 지지하도록 설계하였다. 이 연구에서는 보의 플랜지로부터 스티프너 보강된 ㄱ형강을 통해 강봉이나 연결판으로 전달되는 휨모멘트 전달성능을 확인하고자 구조성능 시험을 수행하였다. 시험체는 실제 보-기둥 접합부를 모델로 하여, 실물크기로 4개가 제작되었으며, 구조실험은 철골 보의 양 단부를 단순지지한 상태에서 기둥 중앙에 집중하중을 가해 보-기둥 접합부에 휨모멘트와 전단력을 작용시키는 방식으로 진행되었다. 실험결과, 이 연구에서 제안된 접합부는 현장 적용이 가능한 가공성과 운반성 및 시공성을 가지며, 철골 보-접합용 ㄱ형강 -연결용 강봉 및 연결판에 의한 응력전달이 매우 순조로운 것으로 나타났다.

• 한국컴퓨터그래픽스학회논문지
• /
• 제23권5호
• /
• pp.9-17
• /
• 2017

시청자의 시야를 콘텐츠로 가득 채워주어 강한 몰입감을 제공하는 다면 영상 제작을 위해서는 다수의 카메라를 이용한 촬영이 요구된다. 이러한 촬영 시나리오에서는 다수의 카메라에 의해 촬영되고 있는 화면들이 하나의 콘텐츠로써 어떻게 보여질지 혹은 실제 상영관에서 어떻게 보여질지 확인하는 모니터링 과정이 매우 중요하다. 기존의 특수 포맷 영상 촬영에 관한 연구들은 모두 스테레오스코픽 입체 영상이나 파노라마 영상 등 각자의 목적에 집중하여 이루어져 왔으며, 최근 확산되고 있는 세 개의 면을 이용한 다면 상영관에 최적화된 콘텐츠 제작에 관한 연구는 부재하다. 본 논문에서는 세 대의 카메라를 제어할 수 있는 리그와 다면 영상 포맷에 특화된 모니터링 소프트웨어를 이용한 다면 콘텐츠 현장 촬영 시스템을 제안한다. 제안된 리그는 카메라 간의 각도를 정밀하게 조절하여 세 대의 카메라로 넓은 화각을 촬영할 수 있으며, 원격 통신을 통해 모니터링 소프트웨어와 연동된다. 모니터링 소프트웨어는 실시간으로 들어오는 영상들을 자동으로 정렬해주며, 수신 받은 리그의 각도에 따라 영상의 정렬이 자동으로 업데이트된다. 또한 촬영 시에 얻어진 정렬 정보를 후반작업에 사용할 수 있게 함으로써, 제작 효율을 크게 향상시킨다.

• Journal of Periodontal and Implant Science
• /
• 제26권1호
• /
• pp.266-275
• /
• 1996

The purpose of this study was to evaluate the effect of anatomical predisposing factors on the development of furcation involvement. Root trunk length, root divergency angle, buccal root trunk concavity and cervical enamel projection of the mandibular 1st and 2nd molars with(l03 teeth) and without(42 teeth) furcation involvement and enamel projection were classified by Lindhe's degree and Masters's classification, respectively, and buccal root trunk concavity was examined by probing. Statistical analysis was performed by means of ANOVA and CHI-SQUARE test in Microstat. The obtained results were as follows : 1. Root trunk length was longer in teeth without furcation involvement($4.20{\pm}1.05mm$) than teeth with furcation involvement(I : $3.62{\pm}0.68mm$, II : $3.64{\pm}0.86mm$, III: $3.61{\pm}0.74mm$)(p<0.05), but there was fno significant difference among furcation involvement group according to the degree of furcation involvement(p0>.05). 2. The root divergency angle was wider in teeth with furcation involvement(I : $53.14^0{\pm}15.11^0$, II : $44.82^0{\pm}14.26^0$, III : $52.69^0{\pm}16.09^0$) than teeth without furcation involvement($34.81^0{\pm}16.57^0$(p<0.05). 3. The group of teeth without furcation involvement showed significantly hign percentage of teeth without buccal root concavity, and the group of teeth with furcation involvement showed significantly hign percentage of teeth with buccal root concavity(p<0.05) 4. The group of teeth without furcation involvement showed higher percentage of teeth with grade I cervical enamel projection, teeth with furcation involvement I or II defect showed higher percentage of teeth with grade II enamel projection, and teeth with furcation involvement III defect showed higher percentage of teeth with grade III enamel projection(p<0.05) The results suggest that short root trunk length, wide root divergency, buccal root concavity and well-developed enamel projection could affect development and progression of furcation involvement as anatomical predisposing factors of periodontal diseases.

• Journal of Mechanical Science and Technology
• /
• 제18권5호
• /
• pp.770-779
• /
• 2004

This paper describes the micro cutting of wear resistant tungsten carbides using PCD (Poly-Crystalline Diamond) cutting tools in performance with SEM (Scanning Electron Microscope) direct observation method. Turning experiments were also carried out on this alloy (V50) using a PCD cutting tool. One of the purposes of this study is to describe clearly the cutting mechanism of tungsten carbides and the behavior of WC particles in the deformation zone in orthogonal micro cutting. Other purposes are to achieve a systematic understanding of machining characteristics and the effects of machining parameters on cutting force, machined surface and tool wear rates by the outer turning of this alloy carried out using the PCD cutting tool during these various cutting conditions. A summary of the results are as follows: (1) From the SEM direct observation in cutting the tungsten carbide, WC particles are broken and come into contact with the tool edge directly. This causes tool wear in which portions scrape the tool in a strong manner. (2) There are two chip formation types. One is where the shear angle is comparatively small and the crack of the shear plane becomes wide. The other is a type where the shear angle is above 45 degrees and the crack of the shear plane does not widen. These differences are caused by the stress condition which gives rise to the friction at the shear plane. (3) The thrust cutting forces tend to increase more rapidly than the principal forces, as the depth of cut and the cutting speed are increased preferably in the orthogonal micro cutting. (4) The tool wear on the flank face was larger than that on the rake face in the orthogonal micro cutting. (5) Three components of cutting force in the conventional turning experiments were different in balance from ordinary cutting such as the cutting of steel or cast iron. Those expressed a large value of thrust force, principal force, and feed force. (6) From the viewpoint of high efficient cutting found within this research, a proper cutting speed was 15 m/min and a proper feed rate was 0.1 mm/rev. In this case, it was found that the tool life of a PCD tool was limited to a distance of approximately 230 m. (7) When the depth of cut was 0.1 mm, there was no influence of the feed rate on the feed force. The feed force tended to decrease, as the cutting distance was long, because the tool was worn and the tool edge retreated. (8) The main tool wear of a PCD tool in this research was due to the flank wear within the maximum value of $V_{max}$ being about 260 $\mu\textrm{m}$.

• Journal of Advanced Marine Engineering and Technology
• /
• 제39권1호
• /
• pp.105-114
• /
• 2015

여객선에서는 승선자의 안전이 가장 중요함에도 불구하고 국내에서는 인간의 피난행동특성을 반영한 피난성능에 관한 기준이 없다. 본 연구에서는 세월호 증개축 전후의 인적피난안전성을 비교 평가하고 이를 통해 현재 기준의 문제점을 도출하고자 하였다. 연구성과를 정리하면 다음과 같다. 첫째, 증개축 전후의 소집장소 면적은 동일하였고, 이 면적은 모두 국내 관련 기준을 만족하는 것으로 평가되지만, 인간의 행동특성을 반영한 인적안전피난시뮬레이션 툴을 활용하면 소집이 불가능한 것으로 판단된다. 둘째, 증개축 전후 선내 공간구성에 대해 각 선실에서 퇴선까지의 피난소요시간예측 시뮬레이션을 50회씩 수행한 결과 힐링각 $0^{\circ}$ 경우에는 모두 SOLAS의 허용기준이내이므로 승객 전원이 충분히 피난할 수 있을 것으로 평가되지만, 힐링각이 $20^{\circ}$인 긴급한 상황에서 피난을 개시할 경우에는 모두 SOLAS의 주간기준은 만족하지만, 야간기준은 만족하지 못하는 것으로 예측되었다. 모든 경우에서 증축 후인 세월호의 피난시간 확률분포가 Naminoue호의 피난시간 확률분포보다 분산되어 있는데 이는 증축후 피난환경이 열악해졌다는 의미이다.

• 한국재료학회지
• /
• 제16권4호
• /
• pp.225-230
• /
• 2006

Nanoimprint lithography (NIL) is a novel method of fabricating nanometer scale patterns. It is a simple process with low cost, high throughput and resolution. NIL creates patterns by mechanical deformation of an imprint resist and physical contact process. The imprint resist is typically a monomer or polymer formulation that is cured by heat or UV light during the imprinting process. Stiction between the resist and the stamp is resulted from this physical contact process. Stiction issue is more important in the stamps including narrow pattern size and wide area. Therefore, the antistiction layer coating is very effective to prevent this problem and ensure successful NIL. In this paper, an antistiction layer was deposited and characterized by PECVD (plasma enhanced chemical vapor deposition) method for metal stamps. Deposition rates of an antistiction layer on Si and Ni substrates were in proportion to deposited time and 3.4 nm/min and 2.5 nm/min, respectively. A 50 nm thick antistiction layer showed 90% relative transmittance at 365 nm wavelength. Contact angle result showed good hydrophobicity over 105 degree. $CF_2$ and $CF_3$ peaks were founded in ATR-FTIR analysis. The thicknesses and the contact angle of a 50 nm thick antistiction film were slightly changed during chemical resistance test using acetone and sulfuric acid. To evaluate the deposited antistiction layer, a 50 nm thick film was coated on a stainless steel stamp made by wet etching process. A PMMA substrate was successfully imprinting without pattern degradations by the stainless steel stamp with an antistiction layer. The test result shows that antistiction layer coating is very effective for NIL.

• 대한치과보철학회지
• /
• 제44권3호
• /
• pp.284-294
• /
• 2006

Statement of problem. Proliferation of Candida albicans is primarily within the plaque on the fitting surface of the denture rather than on the inflamed mucosa. Consequently, the treatment of the denture is equally important as treatment of the tissue. Cleansing and disinfection should be efficiently carried-out as the organisms can penetrate into the voids of the acrylic resin and grow in them, from which they can continue to infect and reinfect bearing tissues. Purpose. The purpose of this study was to evaluate the applicability of photocatalytic reaction to eliminate Candida albicans from acrylic resin denture base, and to investigate the anti-fungal effect with various UVA illumination time. Materials and Methods. The specimens were cured by the conventional method following the manufacturer's instruction using thermal polymerized denture base resin (Vertex RS: Dentimex, Netherlands). $TiO_2$ photocatalyst sol(LT), which is able to be coated at normal temperature, was made from the Ti-alkoxide progenitor. The XRD patterns, TEM images and nitrogen absorption ability of the $TiO_2$ photocatalyst sol(LT) were compared with the commercial $TiO_2$ photocatalyst P-25. The experimental specimens were coated with the mixture of the $TiO_2$ photocatalyst sol(LT) and binder material (silane) using dip-coater, and uncoated resin plates were used as the control group. Crystallinity of $TiO_2$ of the specimen was tested by the XRD. Size, shape and chemical compositions were also analyzed using the FE-SEM/ EDS. The angle and methylene blue degradation efsciency were measured for evaluating the photocatalytic activity of the $TiO_2$ film. Finally, the antifungal activity of the specimen was tested. Candida albicans KCTC 7629(1 ml, initial concentration $10^5$ cells/ ml) were applied to the experiment and control group specimens and subsequently two UVA light source with 10W, 353 nm peak emission were illuminated to the specimens from 15cm above. The extracted $2{\mu}l$ of sample was plated on nutrient agar plate ($Bacto^{TM}$ Brain Heart Infusion; BD, USA) with 10 minute intervals for 120 minute, respectively. It was incubated for 24 hours at $37^{\circ}C$ and the colony forming units (CFUs) were then counted. Results. Compared the characteristics of LT photocatalyst with commercial P-25 photocatalyst, LT were shown higher activity than P-25. The LT coated experimental specimen surface had anatase crystal form, less than 20 nm of particle size and wide specific surface area. To evaluate the photocatalytic activity of specimens, methylene blue degradation reaction were used and about 5% of degradation rate were measured after 2 hours. The average contact angle was less than $20^{\circ}$ indicating that the LT photocatalyst had hydrophilicity. In the antifungal activity test for Candida albicans, 0% survival rate were measured within 30 minute after irradiation of UVA light. Conclusion. From the results reported above, it is concluded that the UVA-LT photocatalytic reaction have an antifungal effect on the denture surface Candida albicans, and so that could be applicable to the clinical use as a cleaning method.

• 한국운동역학회지
• /
• 제17권1호
• /
• pp.165-174
• /
• 2007

The subject of this study was male apparatus gymnastics athlete who had scored high points doing basket with 1/2 turn on parallel bars. Then 3D motion analysis were used to calculate & analyse kinematic variables of Basket with 1/2 turn to Handstand. 1. The total average time spent for Basket with 1/2 turn took $2.16{\pm}.08sec$, at the downward upward phase took $.58{\pm}0.00sec$, $.23{\pm}.00sec$, at flight phase took $.28{\pm}.01sec$, at connected area phase took $.72{\pm}0.21sec$, at rotation area phase took $.35{\pm}.14sec$. To have a successful performance, there should be faster speed and velocity to rotate at the downward upward phase, then the upward velocity and height must be used adequately. Moreover, the speed must be faster at the flight connect phase to stabilize Center of Mass(CM) for the body, and must secure more time at the rotation area to have more stable performance. 2. After handstand on parallel bars while moving CM to right hand side, and It must be performed with big and magnificent performance with putting both hand's center to far away from the parallel bars. 3. Furthermore, CM must be moved fast from downwards to right hand side, and CM must be moved fast in vertical movement at upward and flight phase to avoid CM from moving back and forth, and left and right. 4. At downwards, the subject must rotate as bis as possible using hip-joint as wide as possible and at upwards, must put his body to vertical to have stable performance. While rotating or turning, it is better to do with bigger shoulder angle and have to make sure that trunk angle must be not scattered. To perform better and more positive in basket with 1/2 turn on parallel bars, the centrifugal force must be used big and fast at downward, and at upward and flight phase, downward movement must change to vertical movement as soon as possible while turning movement must happen at handstand position. Time spent must be shorten at connected area to stabilize CM and turning must be natural as possible while securing the necessary time of movement to well-balanced. Also, the body must be vertically closed from the ground.

• Korean Chemical Engineering Research
• /
• 제59권4호
• /
• pp.542-547
• /
• 2021

글라스 라이닝 임펠러는 강산을 포함한 대부분의 화학물질들에 대해 내부식성이 있고, 또한 평활하고 눌어붙지 않는 표면을 가지며 세정이 용이하고 프로세스에 불순물들을 유입하지 않는 강점을 갖고 있다. 글라스 라이닝 HOMEBASE 임펠러는 저점도 유체에서 고점도 유체까지 폭넓은 점도 범위의 액체를 교반할 수 있도록 개발된 다목적형 대형 교반 임펠러이나, 그중에서도 세포 배양이나 효모의 배양, 맥주 발효 솥 등은 저점도 액의 통기 교반에 많이 사용하며, 특히 공기-수계의 통기성 교반에 많이 적용한다. 구조가 간단하면서도 성능 면에서 경쟁력을 갖는 HOMEBASE 임펠러에 대한 글라스 라이닝은 제작상 임펠러와 샤프트의 접합 면적을 가능한 한 작게 할 수 있도록 상하 분할이 필수적이다. 임펠러의 상하 분할은 혼합 성능에는 거의 영향을 미치지 않지만, 통기 성능을 저하하였다. 본 연구에서는 Glass Lined HOMEBASE 임펠러 형상의 최적화를 위해, 상·하부로 분할된 임펠러 사이의 장착각도차와 임펠러 사이의 간격 및 방해판의 개수가 통기 동력에 미치는 영향에 관한 연구를 수행하였다. 상·하부로 분할된 임펠러 사이의 장착각도차와 간격이 통기를 할 때의 동력 P_g와 통기가 없을 때의 동력 P₀의 비인 P_g/P₀를 저하시킨다는 연구 결과를 통해 Glass Lined HOMEBASE 임펠러 최적 형상과 방해판 조건을 도출하였다.