• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.33 no.2
• /
• pp.121-128
• /
• 2020

The purpose of this study is to investigate the distribution patterns of displacement and acceleration fields in a nonlinear soil ground based on the interaction of high-speed train, wheel, rail, and ground. For this purpose, a high-speed train in motion was modeled as the actual wheel, and the vertical contact of wheel and rail and the lateral contact, caused by meandering motion, were simulated; this simulation was based on the moving mass analysis. The soil ground part was given the nonlinear behavior of the upper ground part by using the modified the Drucker-Prager model, and the changes in displacement and acceleration were compared with the behavior of the elastic and inelastic grounds. Using this analysis, the displacement and acceleration ranges close to the actual ground behavior were addressed. Additionally, the von-Mises stress and equivalent plastic strain at the ground were examined. Further, the equivalent plastic and total volumetric strains at each failure surface were examined. The variation in stresses, such as vertical stress, transverse pressure, and longitudinal restraint pressure of wheel-rail contact, with the time history was investigated using moving mass. In the case of nonlinear ground model, the displacement difference obtained based on the train travel is not large when compared to that of the elastic ground model, while the acceleration is caused to generate a large decrease.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.3
• /
• pp.457-465
• /
• 1988

The inside contact characteristics in abrasive belt drives were investigated analytically and experimentally for (1) driver pulley contact wheel and (2) driven pulley contact wheel. The concentrated contact forces in the grinding zone divided the entire belt-pulley contact are by three distinct areas and the tangential friction forces in the active areas caused the normal forces to change, which resulted in the different belt force distribution compared with those of the ordinary flat belt drives. The experimental results for the normal pressure (belt tension) distribution were in good agreement with the theoretical results.

• Journal of Mechanical Science and Technology
• /
• v.15 no.11
• /
• pp.1490-1498
• /
• 2001

In this paper, a regenerative braking algorithm is presented and performance of a hybrid electric vehicle (HEV) is investigated. The regenerative braking algorithm calculates the available regenera tive braking torque by considering the motor characteristics, the battery SOC and the CVT speed ratio. When the regenerative braking and the friction braking are applied simultaneously, the friction braking torque corresponding to the regenerative braking should be reduced by decreasing the hydraulic pressure at the front wheel. To implement the regenerative braking algorithm, a hydraulic braking module is designed. In addition, the HEV powertrain models including the internal combustion engine, electric motor, battery, CVT and the regenerative braking system are obtained using AMESim, and the regenerative braking performance is investigated by the simulation. Simulation results show that the proposed regenerative braking algorithm contributes to increasing the battery SOC which results in the improved fuel economy. To verify the regenerative braking algorithm, an experimental study is performed. It is found from the experimental results that the regenerative braking hydraulic module developed in this study generates the desired front wheel hydraulic pressure specified by the regenerative braking control algorithm.

• Journal of Sensor Science and Technology
• /
• v.27 no.2
• /
• pp.126-131
• /
• 2018

Unlike the hydraulic power steering (HPS) system, which operates by the high pressure of a fluid obtained from the engine power, the motor-driven power steering (MDPS) system uses an electric motor to steer the wheel without consuming engine power. To steer the wheel with an electric motor, a worm wheel and a worm gear rotating between the steering shaft and motor are required. Any imperfection during the construction of an MDPS system or in a composing part creates noise and vibration, which can be sensed by a driver. To solve the noise and vibration problems, each part must be designed to not resonate with other parts. In this work, we developed the measurement and analysis systems to obtain the noise and the vibration of an automobile MDPS system. A signal analyzer was equipped with a 96 kHz, 24-bit ADC and a 150 MHz digital signal processor. The predetermined threshold value of the vibration in the MDPS system was used to determine the pass/fail, and the results were displayed on the screen. Our system can be used in the fabrication line to swiftly determine any imperfections in the MDPS system construction.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.6
• /
• pp.120-127
• /
• 2007

This paper describes the development of a nonlinear observer for four wheel steer (4WS) vehicle. An observer is designed to estimate the vehicle variables difficult to measure directly. A brake yaw motion controller (BYMC), which uses a PID control method, is also proposed for controlling the brake pressure of the rear and inner wheels to enhance lateral stability. It induces the yaw rate to track the reference yaw rate, and it reduces a slip angle on a slippery road. The braking and steering performances of the anti-lock brake system (ABS) and BYMC are evaluated for various driving conditions, including straight, J-turn, and sinusoidal maneuvers. The simulation results show that developed ABS reduces the stopping distance and increases the longitudinal stability. The observer estimates velocity, slip angle, and yaw rate of 4WS vehicle very well. The results also reveal that the BYMC improves vehicle lateral stability and controllability when various steering inputs are applied.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.6
• /
• pp.84-90
• /
• 2010

This paper presents the shape optimization process for the automotive wheel bearing seal lip using the finite element method and the response surface method. First, to predict performance of the bearing seal lip, we used the non-linear finite element analysis. And then, we compared the analysis results with the test results to verify the finite element model. The objective function in optimizing process was obtained from results of the mud slurry test, which is one of many tests for evaluating performance of wheel bearing. After the mud slurry test for the four models which have the similar cross-sectional shape, we measured the wear area of the seal lip and the moisture content in grease. The objective function has been chosen by comparing the results of mud slurry test and characteristics of seal lip, such as contact force, contact area, contact pressure, and interference. Finally, within limited design parameters, we suggested the optimized shape of seal lip, which is expected to improve the wear and the sealing effect of it.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1303-1309
• /
• 2003

This paper presents the static and dynamic measurements for the strength and motion characteristics as well as the improved procedures to assess strength of wheel loaders. Two scenarios for static measurement were decided by which cylinder was actuating. The dynamic measurement was performed for two types of motion, that is, simple reciprocation of the working devices and actual working motion including traveling, digging and dumping. The measured items were stresses, cylinder pressures and strokes. Stress induced by bucket working showed higher level than that by boom working. The measured cylinder speeds were relatively superior to the design speeds. Working stress histories were thought to be closer to static rather than dynamic. A fully assembled FE model was prepared for structural analysis. In this paper, a more simple method was suggested to avoid nonlinearity caused by heave of rear frame under digging forces. Also how brake affected on structural behavior and digging force was examined closely in relation with tire pressure. It was confirmed that the overall stress level of wheel loader during turning traveling with loaded bucket was far lower than the yield stress of material.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2008.09a
• /
• pp.136-143
• /
• 2008

This paper presents the application of a robot which aims at grinding automatically welding-bead remained in the removal job of working pieces for shipbuilding. In specific, the investigation on this application is composed of two parts; one topic is on the development of a robot platform vertically movable on a steel plate of hull, while the other topic is of the development of a grinding tool mechanism in order to remove welding-beads by using a diamond wheel installed on a servo cylinder (which can result in high working pressure on the grinding wheel). Besides, the development of a vision system for tracking welding-beads as well as recognizing welding surfaces is added for the convenience of this robot application to the removal of welding-beads remained in the working pieces for shipbuilding.

• Journal of Mechanical Science and Technology
• /
• v.15 no.1
• /
• pp.66-80
• /
• 2001

In brake systems, a proportioning valve(P. V), which reduces the brake line pressure on each wheel cylinder for the anti-locking of rear wheels, is closely related to the safety of vehicles. However, it is impossible for current P. V. s to completely control brake line pressure because, mechanically, it is an open loop control system. In this paper we describe an electronic brake force distribution system using a direct adaptive fuzzy controller in order to completely control brake line pressure using a closed loop control system. The objective of the electronic brake force distribution system is to change the cut-in-pressure and the valve slop of the P. V in order to obtain better performance of the brake system than with mechanical systems.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.986-993
• /
• 2011

The role of brake is safely to transport passenger & cargo and stop vehicles at emergency in railway vehicle. Brake system reduces the speed by control command of electricity or air. mechanical methods to perform brake are disk brake & tread brake. This study targeted development of highly efficient sintered alloy brake shoe in railway vehicle whose high frictional coefficient, wear resistance, compatibility of the existing tread brake shoe & minimization of wheel's thermal damage and performed development of friction material's formulation, analysis of pressure distribution in wheel tread & brake shoe, optimum form design through analysis of heat flow.