• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.401-401
• /
• 2011

In this work, we deposited Al2O3doped ZnO (AZO) thin films by direct current (DC) magnetron sputtering method with a $40^{\circ}$ tilted target, for application in the front layer of thin film solar cell. Wet chemical etching behavior of AZO films was also investigated. In order to optimize textured AZO films, oxalic acid ($C_2H_2O_4$)has been used as wet etchant of AZO film. In this experiment we used 0.001% concentration of oxalic acid various etching time, that showed an anisotropy in etching texture of AZO films. Electrical resistivity, Hall mobility and carrier concentration measurements are performed by using the Hall measurement, that are $6{\times}10^{-4}{\Omega}cm$, $20{\sim}25cm^2/V-s$ and $4{\sim}6{\times}10^{20}$, respectively.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2003.11a
• /
• pp.105-108
• /
• 2003

The intervention area located at rear hot cell can be contaminated by hot cell maintenance work. For effective decontamination of the intervention floor a wet type decontamination device was developed. The device was assembled with a brush rotating part, a washing liquid supplying part, an intake part for recovering contaminated liquid and a device moving cart part. The device was made of stainless steel for easy decontamination and corrosion resistance. The function test carried out at intervention area of the PIE facility showed good performance.

• Current Photovoltaic Research
• /
• v.6 no.3
• /
• pp.86-90
• /
• 2018

To generate more current in crystalline silicon solar cells, surface texturing is adopted by reducing the surface reflection. Conventionally, random pyramid texturing by the wet chemical process is used for surface texturing in crystalline silicon solar cell. To achieve higher efficiency of solar cells, well ordered inverted pyramid texturing was introduced. Although its complicated process, superior properties such as lower reflectance and recombination velocity can be achieved by optimizing the process. In this study, we investigated optical and passivation properties of inverted pyramid texture. Lifetime, implied-Voc and reflectance were measured with different width and size of the texture. Also, effects of chemical rounding at the valley of the pyramid were observed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.429-429
• /
• 2012

To investigate the gettering effect of B-doped n-type monocrystalline silicon wafer, we made the p-n junction by diffusing boron into n-type monocrystalline Si substrate and then oxidized the boron doped n-type monocrystalline silicon wafer by in-situ wet and dry oxidation. After oxidation, the minority carrier lifetime was measured by using microwave photoconductance and the sheet resistance by 4-point probe, respectively. The junction depth was analyzed by Secondary Ion Mass Spectrometry (SIMS). Boron diffusion reduced the metal impurities in the bulk of silicon wafer and increased the minority carrier lifetime. In the case of wet oxidation, the sheet resistance value of ${\sim}46{\Omega}/{\Box}$ was obtained at $900^{\circ}C$, depostion time 50 min, and drive-in time 10 min. Uniformity was ~7% at $925^{\circ}C$, deposition time 30 min, and drive-in time 10 min. Finally, the minority carrier lifetime was shown to be increased from $3.3{\mu}s$ for bare wafer to $21.6{\mu}s$ for $900^{\circ}C$, deposition 40 min, and drive-in 10 min condition. In the case of dry oxidation, for the condition of 50 min deposition, 10 min drive-in, and O2 flow of 2000 SCCM, the minority carrier lifetime of 16.3us, the sheet resistance of ${\sim}48{\Omega}/{\Box}$, and uniformity of 2% were measured.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.1
• /
• pp.95-106
• /
• 1992

For commercial application of the MCFC, the life time of the MCFC should exceed 40,000 hours, But the life time of the state-of-the-art MCFC was limited to 15,000 hours. The main reasons of the life time limit can be classified as the deficiency of the electrolyte and cathode dissolution. It has been found that the electrolyte deficiency is caused by the continuous evaporation of the electrolyte. However a recent reaserch shows that an electrolyte pumping phenomenon, which implies, the migration of the electrolyte through the gasket material of the external gas manifold, is also the reason of the electrolyte deficiency. Due to the electrolyte pumping phenomenon, positive end cell of the stack suffers the electrolyte deficiency and negative end cell of stack is flooded with electrolyte. Therefore, the cell performance is degraded. The author invented a new manifoldcasing, which prevents the contact between the wet seal and the gasket of the manifold, and gives a complete elimination of an electrolyte pumping effect.

• KSBB Journal
• /
• v.8 no.5
• /
• pp.431-437
• /
• 1993

Active carbon which has the smallest bulk and wet density was found as the best support media among 4 different kinds of materials(celite, natural zeolite, Pusuk stone, active carbon) to make a proper fluidized-bed with small energy consumption. Its minimum and optimum fluidization velocity were found as 0.03cm/sec and 0.25cm/sec, respectively. As organic loading rate for methane fermentation was increased, CODcr removal efficiencies of all the media were decreased. But, CODcr, removal efficiencies of active carbon was maintained more than 90% in this experimental range of the organic loading rate. Larger amount of microorganism was adsorbed on the active carbon which has very high specific surface area. At the organic loading rate of 16g CODcr,/l day, its adsorbed cell mass was 157mg/g. Comparing natural zeolite with roast celite, adsorbed cell mass did not increase in proportion to specific surface area of the media. Even though roast celite has the same specific surface area as the Pusuk stone, its organic removal ability was superior to that of the Pusuk stone, which explains that the relatively great surface roughness and the positive surface charge are important for cell adsorption. It was concluded that the support media for anaerobic fluidized reactor should have small wet density and small fuidization velocity, if possible, in order to increase cell adsorption by reducing the fluid shear stress.

• Journal of Korean Society for Atmospheric Environment
• /
• v.19 no.6
• /
• pp.733-743
• /
• 2003

The flow field in multiple fluid sphere systems was studied analytically. The expanded zero vorticity cell model based on Kuwabara's theory (1959) was applied and the effects of gas slippage at the collecting surface were considered. Also, the solid sphere system was extended to fluid sphere including the effects of the induced internal circulation inside the liquid droplet spheres or gas bubble systems. As a result, the obtained analytic solution was converged to the existing solutions for flow field around solid and bubble sphere systems with proper boundary conditions. Based on the resolved flow field, the terminal velocity around the collecting fluid spheres was obtained. Subsequently, this study evaluated the most general solution for flow field around the multiple fluid sphere systems. The obtained flow field in multiple fluid sphere could be used as a fundamental consideration of wet scrubber design and devices for removing particles by fluid-fluid interactions.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.177-179
• /
• 2007

An object of the present study is to provide a hollow fiber membrane humidifier capable of improving the humidification efficiency while lowering the pressure loss, and is suitably usable for PEMFC(Polymer Electrolyte Membrane Fuel Cell). The performance of PEMFC is decisively dependent on the humidity of the electrolyte membrane(fluorinated membrane) and a humidifier plays an important role in moisturizing electrolyte membrane. Especially, this humidifier is a passive type(power-free) item and is volumetrically optimized. In this research, we propose the substitutes for the expensive fluorinated humidifier materials and the optimum dry-jet wet spinning conditions of hollow fiber membrane. In addition to that, This study will present an performance of an humidifier and compare computational results with the experimental data.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.218-218
• /
• 2011

The CIGS Solar Cells have the highest conversion efficiency in the film-type solar cells. They consist of p-type CuInSe2 film and n-type ZnO film. The CdS films are used as buffer layer in the CIGS solar cells since remarkable difference in the lattice constant and energy band gap of two films. The CdS films are toxic and make harmful circumstances. The CdS films deposition process need wet process. In this works, we design and make the hitter and lamp reflection part in the sputtering system for the ZnS films deposition as buffer layer, not using wet process. Film thickness, SEM, and AFM are measured for the uniformity valuation of the ZnS films. We conclude the optimum deposition temperature for the films uniformity less than 1.6%. The ZnS films deposited by the sputtering system are more dense and uniform than the CdS films deposited by the Chemical Bath Deposition Method(CBD) for the CIGS Solar Cells.

• Journal of Plant Biology
• /
• v.14 no.2
• /
• pp.7-10
• /
• 1971

Haploid cell obta-ined from microspores of Solanum nigrum were cultured on two kinds of medium, "Callus-inducing medium" and "Differentiation medium", in order to conduct histological studies of callus and examine differentiation of plantlets. On the callus-inducing medium the calli grew rapidly. The bulk of callus mass was light brown colored "Wet callus" covered on the surface with thin layers of rough and gleaming "White callus". The wet callus was consisted of parenchyma and meristematic tissues, while the white callus had no meristematic tissues. Large parenchyma cells, by successive divisions, became multicellular or poly nucleate cells which developed later to be meristematic tissues. The calli embedded on the differentiation medium quickly turned to dark brown color. Plantlets, however, came out later from these blackened callus mass. In the callus sectioned about ten weeks after imbedding on the differentiation medium, radially elongated tissue, concentric tissue, epidermis, tracheid-like structure, and plant jprimordia were observed.ure, and plant jprimordia were observed.