• Journal of ILASS-Korea
• /
• v.14 no.4
• /
• pp.147-152
• /
• 2009

Since a liquid-phase LPG injection system allows accurate control of fuel injection and increase in volumetric efficiency, it has advantages in achieving higher engine power and lower emissions compared to the mixer type LPG supplying system. However, this system also leads to an unexpected event called icing phenomenon which occurs when moisture in the air near the injector freezes and becomes frost around the nozzle hole due to extraction of heat from surrounding caused by instant fuel vaporization. As a result, it becomes difficult to control air/fuel ratio in engine operation, inducing exacerbation of engine performance and HC emission. One effort to mitigate icing phenomenon is to attach anti-icing injection tip in the end of nozzle. Therefore, in this study, the effect of engine operation parameters as well as surrounding conditions on icing phenomenon was investigated in a bench test rig with commercially-used anti-icing injection tips. The test results show that considerable ice was deposited on the surface near the nozzle hole of the anti-icing tip in low rpm and low load operating conditions in ambient air condition. This is because acceleration of detachment of deposited ice from the tip surface was induced in high load, high rpm conditions, resulting in decrease in frost accumulation. The results of the bench testing also demonstrate that little or no ice was formed at surrounding temperature below a freezing point since the absolute amount of moisture contained in the intake air is too small in such a low temperature.

• YAKHAK HOEJI
• /
• v.55 no.1
• /
• pp.1-10
• /
• 2011

Mastic is a bleed resin formed in pistacia lentiscus tree extract form the anacatdiaceae family. Mastic is used as a food ingredient in the Mediteraanean resin, and has been used by local inhabitants as a traditional medicine for relief of upper abdominal discomfort, dyspepsiaand peptic ulcer. Clinically, mastic has been effective in the treatment of benign gastric and duodenal, ulcers, giving symptomatic relief and endoscopically proven healing. In this study, to enhance activiteies of poorly water soluble Mastic with oils, surfactants and cosurfactants and then the mixure was microemulsified in aqueous media under condition of gentle agitation and digestive motility that would be encountered in the gastrointestinal tract. Formulation development and screening were based on phase diagrams and characteristics of resultant microemulsion. For optimum mastic formulation, microemulsions with various ratio (w/w%) of mastics, oils, surfactants and cosurfactants were prepared and their solubility was evaluated by monitoring particles size in their buffer through visual asessment and electrophoretic light scattering spectrophotomerter (ELS). In vitro activity of self microemulsified mastic (SME mastic) was determined by minimum ingibition concentration (MIC) test against a panel of Helicobacter pylori (H. pylori) clinical strains. Additionally, in vivo activity of SME masitc was investigated us mouse infected by CH275 of H. pylori. The mean diameter of SME mastic was less then 100 nm in water and SME mastic was showed similar antiboisis effect compared to tometronidazole, clarithromycin and omeproazole. Consequently, SME mastic would be effective system to exterminate H. pylori. If mastic were dose with combined treatment, mastic might augur well for effect of H. pylori eradication as good remedy.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.2
• /
• pp.399-406
• /
• 2009

In this study, Polynomial Radial Basis Function Neural Network(pRBFNN) based on Fuzzy Inference System is designed and its parameters such as learning rate, momentum coefficient, and distributed weight (width of RBF) are optimized by means of Particle Swarm Optimization. The proposed model can be expressed as three functional module that consists of condition part, conclusion part, and inference part in the viewpoint of fuzzy rule formed in 'If-then'. In the condition part of pRBFNN as a fuzzy rule, input space is partitioned by defining kernel functions (RBFs). Here, the structure of kernel functions, namely, RBF is generated from HCM clustering algorithm. We use Gaussian type and Inverse multiquadratic type as a RBF. Besides these types of RBF, Conic RBF is also proposed and used as a kernel function. Also, in order to reflect the characteristic of dataset when partitioning input space, we consider the width of RBF defined by standard deviation of dataset. In the conclusion part, the connection weights of pRBFNN are represented as a polynomial which is the extended structure of the general RBF neural network with constant as a connection weights. Finally, the output of model is decided by the fuzzy inference of the inference part of pRBFNN. In order to evaluate the proposed model, nonlinear function with 2 inputs, waster water dataset and gas furnace time series dataset are used and the results of pRBFNN are compared with some previous models. Approximation as well as generalization abilities are discussed with these results.

• Clean Technology
• /
• v.22 no.4
• /
• pp.250-257
• /
• 2016

As an attempt to replacing petroleum-based chemicals with bio-based ones, synthesis of furfural from biomass-derived xylose attracts much attention in recent days. Conventionally, furfural from xylose has been produced via the utilization of highly corrosive, toxic, and environmentally unfriendly mineral acids such as sulfuric acid or hydrochloric acid. In this study, microwave-assisted biphasic reaction process in the presence of novel bio-based heterogeneous acid catalysts was developed for the eco-benign and effective synthesis of furfural from xylose. The microwave was irradiated for reaction acceleration and a biphasic system consisting of $H_2O$ : MIBK (1 : 2) was designed for continuous extraction of furfural into the organic phase in order to reduce the undesired side products formed by decomposition/condensation/oligomerization in the acidic aqueous phase. Moreover, sulfonated amorphous carbonaceous materials were prepared from wood powder, the most abundant lignocellulosic biomass. The prepared catalysts were characterized by FT-IR, XPS, BET, elemental analysis and they were used as bio-based heterogeneous acid catalysts for the dehydration of xylose into furfural more effectively. For further optimization, the effect of temperature, reaction time, water/organic solvent ratio, and substrate/catalyst ratio on the xylose conversion and furfural yield were investigated and 100% conversion of xylose and 74% yield of furfural was achieved within 5 h at $180^{\circ}C$. The bio-based heterogeneous acid catalysts could be used three times without any significant loss of activity. This greener protocol provides highly selective conversion of xylose to furfural as well as facile isolation of product and bio-based heterogeneous acid catalysts can alternate the environmentally-burdened mineral acids.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.3
• /
• pp.233-240
• /
• 2023

p-type Tunnel Oxide Passivating Contacts (TOPCon) solar cell is fabricated with a poly-Si/SiO_x structure. It simultaneously achieves surface passivation and enhances the carriers' selective collection, which is a promising technology for conventional solar cells. The quality of passivation is depended on the quality of the tunnel oxide layer at the interface with the c-Si wafer, which is affected by the bond of SiO formed during the subsequent annealing process. The highest cell efficiency reported to date for the laboratory scale has increased to 26.1%, fabricated by the Institute for Solar Energy Research. The cells used a p-type float zone silicon with an interdigitated back contact (IBC) structure that fabricates poly-Si and SiO_x layer achieves the highest implied open-circuit voltage (iV_oc) is 750 mV, and the highest level of edge passivation is 40%. This review presents an overview of p-type TOPCon technologies, including the ultra-thin silicon oxide layer (SiO_x) and poly-silicon layer (poly-Si), as well as the advancement of the SiO_x and poly-Si layers. Subsequently, the limitations of improving efficiency are discussed in detail. Consequently, it is expected to provide a basis for the simplification of industrial mass production.

• Journal of Biosystems Engineering
• /
• v.41 no.2
• /
• pp.85-92
• /
• 2016

Background: The same plant, Camellia sinensis, is used to produce all types of tea, and the differences among the various types arise from the different processing steps that are used. Based on the degree of fermentation, tea can be classified as black, green, white, or oolong tea. Of these, black tea is the most or fully fermented tea. The oxidized polyphenolic compounds such as theaflavins (TF) and thearubigins (TR) formed during fermentation are responsible for the color, taste, flavor, and aroma of black tea. Results: Research indicates that an optimum ratio of TF and TR (1:10) is required to ensure a quality cup of tea. The concentrations of TF and TR as well as desirable quality characteristics increase as fermentation time increases, reaching optimum levels and then degrading if the fermentation time is prolonged. It is also necessary to control the environment for oxidation. There are no established environment conditions that must be maintained during the fermentation of the ruptured tea leaves. However, in most cases, the process is performed at a temperature of $24-29^{\circ}C$ for 2-4 h or 55-110 min for orthodox tea or crush, tear, and curl (CTC) black tea, respectively, under a high relative humidity of 95-98% with an adequate amount of oxygen. Conclusion: The polyphenolic compounds in black tea such as TF and TR as well as un-oxidized catechins are responsible for the health benefits of tea consumption. Tea is rich in natural antioxidant activities and is reported to have great potential for the management of various types of cancers, oral health problems, heart disease and stroke, and diabetes and to have other health benefits such as the ability to detoxify, improve urine and blood flow, stimulate, and improve the immune system.

• Journal of the Korean Solar Energy Society
• /
• v.32 no.5
• /
• pp.41-51
• /
• 2012

Heliostat field is the most important subsystem in the tower type solar thermal power plant since its optical performance affects the total system efficiency most significantly while the construction cost of it is the major part of total construction cost in such a power plant. Thus a well designed heliostat field to maximize the optical efficiency as well as to minimize the land usage is very important. This work presents methodology, procedures and result of heliostat filed design for 200kW solar thermal power plant built recently in Daegu, Korea. A $2{\times}2(m)$ rectangular shaped receiver located at 43(m) high and tilted $28^{\circ}$ toward heliostat field, 450 of heliostats of which the reflective surface is formed by 4 of $1{\times}1(m)$ flat plate mirror facet, and the land area having about $140{\times}120(m)$ size are used to form the heliostat field. A procedure to deploy 450 heliostats in radial staggered nonblocking formation is developed. Also the procedures to compute the cosine effect, intercept ratio, blocking and shading ratio in the field are developed. Finally the heliostat filed is designed by finding the optimal radial distance and azimuthal spacing in radial staggered nonblocking formation such that the designed heliostat field optical efficiency could be maximized. The designed heliostat field has 77% of annual average optical efficiency, which is obtained by annually averaging the optical efficiencies computed between the time of where sun elevation angle becomes $10^{\circ}$ after sunrise and the time of where sun elevation angle becomes $10^{\circ}$ before sunset in each day.

• Journal of the Korean institute of surface engineering
• /
• v.46 no.4
• /
• pp.139-144
• /
• 2013

c-BN(cubic boron nitride) is known to have extremely high hardness next to diamond, as well as very high thermal and chemical stability. The c-BN in the form of film is useful for wear resistant coatings where the application of diamond film is restricted. However, there is less practical application because of difficult control of processing variables for synthesis of c-BN film as well as unclear mechanism on formation of c-BN. Therefore, in the present study, the structural characterization of c-BN thin film were investigated using $B_4C$ target in r.f. magnetron sputtering system as a function of processing variables. c-BN films were coated on Si(100) substrate using $B_4C$ (99.5% purity). The mixture of nitrogen and argon was used for carrier gas. The deposition processing conditions were changed with substrate bias voltage, substrate temperature and base pressure. Fourier transform infrared microscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS) were used to analyze crystal structures and chemical binding energy of the films. In the case of the BN film deposited at room temperature, c-BN was formed in the substrate bias voltage range of -400 V~ -600 V. Less c-BN fraction was observed as deposition temperature increased and more c-BN fraction was observed as base pressure increased.

• Progress in Superconductivity
• /
• v.7 no.2
• /
• pp.130-134
• /
• 2006

Buffer layers such as $CeO_2\;and\;Yb_2O_3$ films for YBCO coated conductors were deposited on (100) $SrTiO_3$ single crystals and (100) textured Ni substrates by a metal organic chemical vapor deposition (MOCVD) system of the hot-wall type. The substrates were moved with the velocity of 40 cm/hr. Source flow rate, $Ar/O_2$ flow rate and deposition temperature were main processing variables. The degree of film epitaxy and surface morphology were investigated using XRD and SEM, respectively. On a STO substrate, the $CeO_2$ film was well grown epitaxially above the deposition temperature of $450^{\circ}C$. However, on a Ni substrate, the XRD showed NiO (111) and (200) peaks due to Ni oxidation as well as (111) and (200) film growth. For the films deposited with $O_2$ gas as oxygen source, it was found that the NiO film was formed at the interface between the buffer layer and the Ni substrate. The NiO layer interrupts the epitaxial growth of the buffer layer. It seems that the epitaxial growth of the buffer layer on Ni metal substrates using $O_2$ gas is difficult. We are considering a new method avoiding Ni oxidation with $H_2O$ vapor instead of $O_2$ gas.

• Journal of architectural history
• /
• v.21 no.4
• /
• pp.7-24
• /
• 2012

The Buddhist cave temple carved into the rock provides a large space for the ritual in general in which a structure of Stupa is built in the center of the space purely for religious worship empty of Sarira, and the temple is formed around this Stupa. Relief-Stupa of the cave temple indicates the similar shape that of Relief-religious worship of flat land temple. However, there appears a small difference in representation since the background of formation of the cave temple differs in that of flat land temple. Specially, Caitya Stupa of currently existing cave temples have been damaged to lose of their original shape only possible to be analyzed the stylistic development through Relief-Stupa from which the characteristic of Stupa could be understood. The early cave temple could be characterized with a balanced structure consists of upturn bowl, steeple stone with simple drum & Hamikawasnagae, in which it appears strongly the detail factor characteristics of drum & steeple of having system with Caitya Stupa. In the post cave temple, the subject of worship moved to statue of Buddha due to the influence of Gandhara, Mathura art which reduced the importance of Stupa. This illustrates in Relief-stupa as well the style change as well as changes in detail factor. The sculpture appeared at the limited location either the wall of Caitya shrine or pillar in vihara cave with stronger decorative meaning. Contrast to the Relief Stupa of early flat land temples or the cave temples mentioned above sculptured with symbolism, however, the post cave temple showed the relief structure based on the plan of flat plan.