• Journal of Welding and Joining
• /
• 제30권1호
• /
• pp.51-58
• /
• 2012

To assess hydraulic connections between sub-components of the International Thermonuclear Experimental Reactor (ITER) diagnostic port plug, the laser welding and ablation cutting process were investigated in order to be applied the remote handling maintenance. In this study, laser ablation cutting, which vaporizes a small amount of solid material directly into gas by focusing a laser beam of high density energy, is adopted in order to overcome the limitation of the normal laser cutting technology that the head should be placed as close to the work piece as possible to blow out melt metal at a distance. Complete cutting of a work piece is obtained by repetitive multi-passes of the laser beam. The welding and cutting process were tested on the sample work pieces and finally on a prototype of a hydraulic connection module for remote handling. The results showed that this process can be a promising candidate for hydraulic connections by remote handling.

• Journal of Welding and Joining
• /
• 제32권5호
• /
• pp.50-57
• /
• 2014

Friction Stir Welding (FSW) is a complex process with several mutually interdependent parameters. A slight difference from known settings may lead to imperfections in the stirred zone. These inhomogeneities affect on the mechanical properties of the FSWed joints. In order to prevent the failure of the welded joint it is necessary to detect the most critical defects non-destructive. Especially critical defects are wormhole and lack of penetration (LOP), because of the difficulty of detection. Online thermography is used process-accompanying for defect detecting. A thermographic camera with a fixed position relating to the welding tool measures the heating-up and the cool down of the welding process. Lap joints with sound weld seam surfaces are manufactured and monitored. Different methods of evaluation of heat distribution and intensity profiles are introduced. It can be demonstrated, that it is possible to detect wormhole and lack of penetration as well as surface defects by analyzing the welding and the cooling process of friction stir welding by passive online thermography measurement. Effects of these defects on mechanical properties are shown by tensile testing.

• Journal of Welding and Joining
• /
• 제14권5호
• /
• pp.59-68
• /
• 1996

This study was aimed to characterize the laser cutting process for the cold rolled stainless steel sheet. The principal process parameters of the cutting process were applied to both the continuous wave form and the pulsed wave form for the laser output mode. The laser-oxygen cutting process and the laser-nitrogen cutting process were also considered to characterize the quality and efficiency of the cutting process. The laser-oxygen cutting process revealed the better productivity than the laser-nitrogen cutting process, since the laser energy and the exothermic oxidation energy exerted on the laser-oxygen cutting process simultaneously during the entire cutting process. However, the straightness of the cutting section, which was considered as the most important factors, was inferior to that of the laser-nitrogen cutting process due to the formation of chromum oxide on the cutting surface. Frequency and duration of the pulsed wave form act as the main factors for the better quality, When the frequency increased from 100 Hz to 200 Hz and the duty increased from 20% to 40%, the quality factors such as the height of dross and the surface roughness were improved remarkably. The increase in the frequency from 200 Hz to 300 Hz, on the other hand, revealed the less effective in the cutting quality.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 추계학술대회 논문집
• /
• pp.493-497
• /
• 2002

In the part industry, pipe has required high accuracy in surface roughness and size. Especially, when producing the high frequency welding pipe, cutting process is very important as the finishing process that remove the hot welding bead. The objective of this paper is to investigate the hot machining high frequency welded pipe by simulation and experimental tests. To test the cutting process as hot machining, all cutting environment is reproduced in turning with heating system, and the test is accomplished by comparing with room temperature machining and hot machining in consideration of cutting force, tool wear and cutting temperature.

• 한국화재소방학회논문지
• /
• 제26권3호
• /
• pp.60-66
• /
• 2012

본 연구에서는 건설현장 등에서 주로 사용되는 용접 절단기의 작업시 화재위험성을 평가하였다. 실험에는 인버터 AC/DC TIG 용접기와 인버터 에어프리즈마 절단기가 사용되었다. 용접 절단 작업시 비산되는 불티의 온도를 측정하였다. 작업높이와 입력전류의 변화에 따라 비산된 불티의 크기 및 비산범위를 측정하였다. 또한, 용접 절단기 화재원인 중 가장 높은 비율을 차지하는 가연물 근접방치에 의한 화재위험성을 평가하였다. 가연물로는 건초, 방진막, 우레탄폼, 비닐, 종이, 유류가 사용되었다. 용접 절단 작업시 불티의 온도가 최대 $450^{\circ}C$까지 상승하였다. 2.5 m 높이에서 절단 작업시 불티가 최대 4.7 m까지 비산되었다. 용접 절단 작업시 주위에 가연물이 존재할 경우 비산된 불티에 의해 가연물에 착화되어 화재로 발전할 가능성이 매우 높다.

• Journal of Welding and Joining
• /
• 제32권6호
• /
• pp.22-28
• /
• 2014

Most publications on friction stir welding describe phenomena or results with given process parameters like feed rate, rotation speed, angle and depth of penetration. But without a complete documentation of tool design, the results under the same process parameters are completely different. For this purpose, the Institute of Cutting and Joining Manufacturing Processes (tff), University of Kassel investigated the influence of tool roughness on the friction stir welding process. Therefore a defined surface finish was produced by turning and die sinking. As basis of comparison the constant parameters were rotation speed, feed rate, tilt angle and a heel plunge depth. Sound butt-welds were produced in aluminium alloy 6082 (AlMgSi1) with 1.5 mm sheet thickness with a turned reference tool with a surface of $Ra=0.575{\mu}m$ in position controlled mode. The surfaces are manufactured from a very fine to a very rough structure, classified by the VDI-classes with differences in the arithmetical mean roughness. It can be demonstrated with the help of temperature measures, that less heat is generated at the surfaces of the shoulder and the pin by the higher roughness due to lower active friction contact surface. This can also be seen in the resulting wormhole defects.

• 한국CDE학회논문집
• /
• 제2권4호
• /
• pp.267-275
• /
• 1997

A ship-block cutting module is being developed as part of a computational system for a ship design. The module supports product-information to other modules in design process and displays ship-blocks in cutting-operation. Welding-information is essential to process-planning and scheduling. In the module, ship-blocks are modeled by Plate-Objects and then divided into several cutting pieces. The module automatically creates Welding-Objects containing welding-information in the process. Since the module is connected to WWW(World Wide Web), users in various platforms can access the models simultaneously In addition, users can check manufacturing constraints by inspecting a virtual model.

• 한국생산제조학회지
• /
• 제18권5호
• /
• pp.469-476
• /
• 2009

Hard facing overlay welding in high chromium carbide is a representative way of extending the fatigue life or recompensing damage, because workpiece surface is uniformly overlay-welded by alloy material. In general, grinding process is currently used for finish due to hardness of weld material. The development of tool material, such as PCBN, has made it possible to use turning instead of grinding. There are many advantages of hard Owning, as lower equipment costs, shorter setup time, fewer process steps, higher material removal rate, better surface integrity and the elimination of cutting fluid. In this paper, machining characteristics and cutting performance are examined to investigate turning possibility of overly welding in high chromium carbide.

• Journal of Welding and Joining
• /
• 제8권3호
• /
• pp.60-69
• /
• 1990

Plasma arc cutting is a fusion cutting process in which a gas-constricted arc is employed to produce a high-temperature, high-velocity plasma jet on the workpiece. This process provides some advantages such as increased cutting velocity, excellent working accuracy and the ability to cut special materials (widely used stainless steels and Al-alloys, for example), when compared with iconventional oxyfuel gas cutting. From the view point of price and reliability of the power source, plasma arc cutting has also some distinct advantages over laser beam cutting. High-speed machines with NC or CNC systems are needed for the plasma arc or laser beam cutting process, while for oxyfuel gas cutting, low-speed machines with copying templates or optical-shape tracking sensors can be applied. The low price and high flexibility of the microprocessor arc contributing more and more the application of CNC system in the plasma arc cutting process, as in other manufacturing fields. From these points of view, a microprocessor-based plasma arc cutting system was developed by using a reference-pulse system, and its performance was tested. The interpolating routines were programmed in the assembly language for saving the memory volume and improving the compouting speed, which has an intimate relationship with the available cutting velocity.

• Journal of Welding and Joining
• /
• 제13권4호
• /
• pp.113-121
• /
• 1995

This study deals with the quality and the optimum range of laser cutting process. Cold rolled steel sheets for automobile application were cut by a high power CO$_{2}$ laser system with beam quality of TEM$_{\infty}$ mode. Both process parameters such as travel speed and assist gas pressure, and quality factors were considered to optimize the laser cutting. It was revealed that the thinner the sheet thickness, the less effect of oxidation energy for contributing the cutting process. High speed photographs demonstrated that molten spot on the cut surface moved in a random and vigorous manner according to its viscosity and the flowing direction of assist gas, which resulted in so called striation. Laser cutting produced a very smooth surface of average roughness(Ra) about less than 1.5.mu.m at the optimum range. It was also shown that the characteristics of dross formation was influenced by the flowing durection of assist gas and the fluidity of molten metal drop..