• Journal of Welding and Joining
• /
• 제35권1호
• /
• pp.74-78
• /
• 2017

In auto ancillary fabrication industry, GMAW is a very useful & important welding process and EN10025 S 235 Grade is common material used for manufacturing of two wheeler chassis. This research gives the detail influence of welding process parameters such as welding current, welding voltage, wire speed on the penetration in EN10025 S 235 Grade mild steel material. The experimentation of this research has been carried out by using three factors, three level Taguchi DOE method. To analyze & optimize the welding parameters & characteristics, analysis of variance, L9 orthogonal array & signal to noise ratio are used. Length of Penetration in addition to the depth of penetration is major concern in fillet welded joints, as the penetration decides the strength of the welded joint. After analysis of penetration in all 9 welded samples, optimize parameters readings verified & found probability value within 0.05.From this research it is come to know that welding current & welding voltage is major parameters which affects the penetration in welded joints.

• Journal of Welding and Joining
• /
• 제28권6호
• /
• pp.28-34
• /
• 2010

This paper was described on investigation to prevent porosity in high speed MIG Welding of Al 6082-T6. Porosity measurement was carried out by using image analysis of micrographs with the help of an analysis software. The main parameter was arc length and torch progressive angle. The porosity ratio was increased as arc length was increased. The arc length was increased depending upon the output voltage. By proper selection of pulse waveform parameter, the stable arc of one pulse one drop was generated. The porosity ratio of optimum condition in one pulse one drop was lower than high voltage condition. When torch progressive angle was an angle of advance $10^{\circ}$, porosity ratio was minium.

• Journal of Welding and Joining
• /
• 제6권2호
• /
• pp.47-55
• /
• 1988

This paper reports on a study of the influence of welding variables on the weld shape of Al-7020 in pulse-GMA welding. Five variables, i.e., wire feed rate, peak pulse current, welding speed, welding votage, and pulse frequency were investigated for their effects on the weld shape. From the results of the 2$^{n-1}$ fractional factorial design, quantitative effects of each variable and the interaction of two variables were obtained, and consequently wire feed rate, welding voltage, and welding speed were determined as the main welding variables. Supplementary experiment was performed for ivestigating the detailed relationship between the main variables nd the seld shape. In this experiment, the penetation of the seldment increased when the wire feed rate was raised, nad the bead width increased when the welding voltage was raised or the welding speed was reduced.d.

• 대한조선학회논문집
• /
• 제56권6호
• /
• pp.473-479
• /
• 2019

Welding is one of the most popular joining methods and most welding quality estimation methods are executed using joined material. This paper propose welding quality estimation methods using dynamic current, voltage and resistance which are obtained during welding in real time. There are many kinds of welding method. Among them, we focused on the projection welding and gathered dynamic characteristics from two different types of projection welding. For image learning, graphs are drawn using obtained current, voltage and resistance, and the graphs are converted to images. The images are labeled with two sub-categories - normal and defect. For deep learning of images obtained from welding, Convolutional Neural Network (CNN) is applied, and Tensorflow was used as a framework for deep learning. With two resistance welding test datasets, we conclude that the Convolutional Neural Network helps in predicting the welding quality.

• Journal of Welding and Joining
• /
• 제22권1호
• /
• pp.58-64
• /
• 2004

The control of the weld bead shape is important in laser welding of the small parts. The effects of laser welding parameters on the weld bead shape in the pulsed Nd:YAG laser welding of STS 304L material were investigated. Shielding gas type, flow rate, pumping voltage, pulse frequency, pulse width, focal position and overlap distance were selected as laser welding parameters. Experiments were designed and conducted using the Taguchi method which was a statistical experimental method. The weld bead width, penetration, area and aspect ratio were measured and analysed as the weld bead shape properties and the welding parameters were optimized to maximize the weld aspect ratio. Weld aspect ratio were greatly affected by the pulse width, pumping voltage and pulse frequency, and somewhat by the overlap distance, and little by the shielding gas type, flow rate and focal position. A confirmation experiment were conducted using the optimized welding parameters.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 춘계 학술발표대회 개요집
• /
• pp.115-117
• /
• 2004

Nd:YAG laser welding system was used to manufacture instrumented irradiation fuel. The optimal condition of zircaloy-4 seal tube is charge voltage 180V and pulse per energy 51. We got good welding result in charge voltage 400V, pulse width 7ms, pulse frequency 5 in zircaloy-4 endcap welding.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 춘계학술발표대회 개요집
• /
• pp.65-67
• /
• 2002

The gas metal arc welding(GMAW) is regarded as one of the best candidate for welding automation in industrial joining application. It is important to monitor the weld quality for the high performance of weld automation. The measured analog signal is frequency analyzed by digital signal process method. In order to observe the welding phenomena and control welding condition, arc light, voltage, and current are measured at the same time. They are analyzed and compared with arc sound. for these experiments, a power source of constant voltage characteristics was used in the pure metal transfer mode.

• Journal of Welding and Joining
• /
• 제32권6호
• /
• pp.35-40
• /
• 2014

The contact tip for gas metal arc welding has important functions to transmit the welding current to the wire and to guide the wire to molten pool. If the contact tip is damaged, it is a cause of lowering the welding productivity due to removal of welding defects and replacement of contact tip. In case of the use of a contact tip for a long time the arc is unstable because the processed hole in the contact tip center is larger, and the variation of aiming position of the welding wire causes a seam tracking error. In this study, gas metal arc welding experiments using contact tip of three different materials were performed. The contact tips with Cu-P, Cu-Cr, and Cu-ODS were used at the experiments, and the welding characteristics by each contact tip were evaluated. After welding contact tip appearance, welding spatter adhesion amount of the nozzle, and weld bead appearance were evaluated. The welding current and welding voltage were measured to verify arc stability during arc welding.

• Journal of Welding and Joining
• /
• 제8권1호
• /
• pp.31-42
• /
• 1990

Arc must be stable during welding first of all other factors for obtaining sound weldment, especially in the automation of welding process. Arc stability is somewhat sophisticated phenomenon which is not clearly defined yet. In consumable electrode welding, the voltage and current variation due to metal transfer enables to assess arc stability. Recently, statistical analyses of the voltage and current waveform factors are performed to assess the degress of arc stability which is assessed and controlled by operator's own experience by now. But, considering the increasing need and the trend of automation of welding process, it is necessary to monitor arc stability in real-time. In this sutdy, the modified stability index composed of two voltage and current wvaeform factors (arc time and short circuit time) reduced from four factors (arc time, short circuit time, average arc current and average short circuit current) in Mita's index by the welding electrical circuit modeling is proposed and verified by experiments to be well estimating arc stability in the static sense. Also, the recursive calculation form estimating present arc stability in the dynamic sense is developed for real-time estimation. The results of applying the recursive index during welding show good estimation of arc stability in real-time. Therefore, the results of this study offers the mean for real-time control arc stability.

• 한국산학기술학회논문지
• /
• 제20권8호
• /
• pp.133-138
• /
• 2019

본 논문은 자동차 구조용 열간 압연 강재인 SAPH440을 GMAW 겹치기 용접을 하여 용접 변수인 용접 전류, 용접 전압, 이송 속도를 달리하여 인장 특성을 평가하였다. GMAW 공정의 접합 변수에 따라 인장 시험을 수행하기 위하여 겹치기 용접 하여 KS B ISO 9018에 따라 시험편을 제작하여 실험하였다. 각 조건에 따른 비드 외관을 관찰하였고 그에 따른 인장시험을 하여 용접성을 평가하였다. 평가 결과 용접전류가 높을수록 깊은 용입이 형성되는 것을 알 수 있었으나 인장강도 측면에서는 모재부 파단으로 인해 일정 변수 이상부터는 큰 차이는 없는 것으로 확인되었다. 용접 전류 200A, 용접 전압 17V의 조건에서와 같이 전압에 비해 전류가 높으면 다량의 스패터가 발생하며 용접이 불안정하고 이로 인해 용접부 파단이 일어나는 것을 확인 하였다. 전압이 높을수록 대체로 결함이 발생 되지 않을 정도의 비드외관을 관찰할 수 있었으며 너무 높은 전압 또한 용접성에 영향을 끼치는 것을 확인하였다. 너무 낮은 전류와 전압의 조건에서는 용접이 정상적으로 되지 않아 인장강도를 측정할 수 없었다. 그러나 용접이 가능한 용접 조건에서는 전류가 증가함에 따라 전압과 이송속도가 증가하더라도 인장강도에는 큰 영향을 미치지 않았다.