• Journal of Welding and Joining
• /
• v.31 no.3
• /
• pp.54-59
• /
• 2013

Several methodologies analyzing welding distortions of large shell structures like ship blocks have been developed and utilized in shipyards for a long times ago. In general, one of objects of thermal distortion analysis is to find welding sequence making least-deformation without any suppliance, and it can be solved easily and rapidly by EP strain-boundary method. But after assembly construction, there are usually more than 10 weldments in each process, and the number of sequence will follow the Factorial calculation. In this research, a method has been suggested to decide the best welding sequence by minimum analysis. Using this method, welding deformation could be reduced just analyzing some cases as many as the number of weldments. Experiments and Analysis of all cases were also done, and their best results are good agreements with predictation by suggested methodology.

• Journal of Welding and Joining
• /
• v.29 no.4
• /
• pp.73-79
• /
• 2011

Friction stir welding (FSW) is a solid state joining method patented in 1991 by The Welding Institute (TWI). It is widely used for joining light metals such as Al and Mg alloys. Foreign railway vehicle manufacturing companies have been applying FSW to car body welding, but domestic companies are in the beginning of feasibility study. Therefore, lots of experimental and analytical study is needed. In this study, three-dimensional finite element modeling of the friction stir welding of two Al6061-T6 plates was carried out. And temperature field and residual stresses were obtained and compared to experimental results in the literature. It is found the analytic thermal field is in a good agreement with the experimental results, but there are some differences between numerical and experimental residual stresses.

• Journal of Welding and Joining
• /
• v.27 no.4
• /
• pp.67-72
• /
• 2009

In this paper, arc characteristics of V groove joints using pulsed GMA welding were found out. The bevel angles of $22.5^{\circ}$ and $30.0^{\circ}$ were chose to make the V groove configuration with the groove angles of $45^{\circ}$ and $60.0^{\circ}$, respectively. In the experiment, the arc current waveform measurement and the high speed photography were taken to investigate the arc characteristics for a single-beveled asymmetric workpiece. Consequently, the welding current was changed abnormally around the edge of groove. As the arc moved close to the groove face, the welding current was increased rapidly because the welding arc was affected by the inclined surface. Also the welding current waveforms were measured for the double-sided symmetric workpiece to verify the previous measurements for the single-beveled workpiece, and similar current waveforms were found.

• Journal of Welding and Joining
• /
• v.28 no.4
• /
• pp.55-60
• /
• 2010

The purpose of this paper is to propose a mathematical model of welding current for the P-GMAW by modifying the well known GMAW model. Welding power circuit is simply modeled as a RL electric circuit and solved as an ODE equation. The welding current depends on the joint shape, molten pool and welding parameters. To compare the molten pool effect to the welding current, CFD numerical simulation technique was adopted. Welding experiment is also conducted with the same welding parameters as used in numerical simulations to verify the proposed welding current model. The current model which is considered molten pool shape, is more fit to experiment result.

• International Journal of Korean Welding Society
• /
• v.1 no.1
• /
• pp.44-50
• /
• 2001

A genetic algorithm was applied to the arc welding process as to determine the near-optimal settings of welding process parameters that produce the good weld quality. This method searches for optimal settings of welding parameters through the systematic experiments without the need for a model between the input and output variables. It has an advantage of being capable to find the optimal conditions with a fewer number of experiments rather than conventional full factorial designs. A genetic algorithm was applied to the optimization of the weld bead geometry. In the optimization problem, the input variables were wire feed rate, welding voltage, and welding speed. The output variables were the bead height bead width, and penetration. The number of levels for each input variable is 16, 16, and 8, respectively. Therefore, according to the conventional full factorial design, in order to find the optimal welding conditions,2048 experiments must be performed. The genetic algorithm, however, found the near optimal welding conditions in less than 40 experiments.

• Proceedings of the KWS Conference
• /
• 2008.05a
• /
• pp.23-23
• /
• 2008

• Proceedings of the KWS Conference
• /
• 2002.05a
• /
• pp.204-206
• /
• 2002

To excavation of contents of welding portal site for collect the welding information and to development of circulation system, the needs and utilization of technical information in welding were investigated. This investigation was performed about 300 peoples with domestic university and college, research institute and industry.

• Journal of Welding and Joining
• /
• v.30 no.5
• /
• pp.4-8
• /
• 2012

• Journal of Welding and Joining
• /
• v.28 no.4
• /
• pp.73-80
• /
• 2010

In this work, the effect of welding variables on weldability of gas tungsten arc(GTA) welding was investigated with experimental analysis for a commercial pure(CP) titanium (Grade.1). The GTA welding tests on sheet samples with 0.5mm in thick were carried out at different process variables such as arc length, welding speed and electrode shape. In order to search an optimum arc length with full penetration, bead- on-plate welding before butt-welding were performed with different arc length conditions. From the bead- on-plate welding results, the optimum condition considering arc stability and electrode loss was obtained in the arc length of 0.8mm. Butt-welding tests based on the arc length of 0.8mm were carried out to achieve the optimum conditions of welding speed and electrode shape. Optimum conditions of welding speed and electrode shape were suggested as 10 mm/s and truncated electrode shape, respectively. It was successfully validated by the microstructural observation, tensile tests, micro-hardness tests and formability tests.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.511-515
• /
• 2002

Extruded and cast plates of AZ type magnesium alloys were successfully joined by friction stir welding (FSW). Effect of FSW conditions on the formation of the defect was revealed in relation to tool rotation speed and specimen travel speed. Magnesium alloy with higher aluminum content became difficult to be joined and the optimum condition without defect was restricted into narrow condition range. The structure of the stirred zone was a fine-grained recrystallized structure even in the case of cast AZ91D. FSW joint had better mechanical properties than those of GTA welded joint. Especially the toughness of the stirred zone increased more than that of the base metal.