• 한국산학기술학회논문지
• /
• 제17권8호
• /
• pp.706-713
• /
• 2016

본 연구에서는 이종소재 A6005-AZ61 접합을 위하여 마찰교반용접의 툴 삽입 위치와 모재의 냉각 유 무에 따라 용접부 특성을 분석하였다. 다른 용접 조건들인 툴 회전속도와 이송속도는 500rpm-30mm/min으로 고정하고 Advancing side에 알루미늄 합금(A6005), Retreating side에 마그네슘 합금(AZ61)을 배치하여 용접을 진행하였다. 용접은 여섯 가지 케이스를 진행하였다. 용접부 특성을 관찰하기 위하여 인장 시험을 진행하고, 광학현미경을 사용하여 용접부의 미세조직을 관찰하였다. 인장시험 결과 마그네슘 합금 방향으로 툴을 1mm 이동시키고 모재에 냉각을 시킨 조건에서 강도가 가장 높게 나타났다. 동일한 용접 조건에서 냉각을 한 경우에 냉각을 하지 않은 것 보다 강도가 약 2배 높게 측정되었다. 툴의 위치는 용접부 중심에서 알루미늄 합금 방향으로 1.7mm, 마그네슘 합금 방향으로 1.7mm 이동시켜 과도한 편심을 적용한 용접 조건에서는 교반이 잘 이루어지지 않아 용접부의 건전성이 가장 좋지 않았다. 과도한 편심을 적용한 용접 조건에서는 교반이 잘 이루어지지 않아 용접부의 건전성이 가장 좋지 않았다. 본 연구를 통해 A6005-AZ61 이종 마찰교반용접시 용접속도와 툴 회전속도만큼 모재의 온도 조절과 툴 삽입위치가 중요한 용접변수임을 확인 하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.917-922
• /
• 2003

In this paper, a high speed rotating arc sensor for automatic fillet welding is introduced. In order to track the welding seam, The high speed rotating arc sensor is used. The welding tip of a high speed rotating arc sensor rotates about 3000 rpm using DC motor. The rotating torch is driven by gear between welding torch body and wire guide. The welding current is measured by using the current sensor and rot at ing position sensor. To realize the welding seam tracking algorithm with accuracy, a software filter algorithm using the moving average method is applied to the measured welding current in the microprocessor. The welding mobile robot with two wheels and two sliders is developed for fillet welding. The welding mobile robot can control its traveling direction and turn itself around the corner. The effectiveness is proven through the experimental results conducted with varied fillet tracking patterns.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2007년 추계학술발표대회 개요집
• /
• pp.42-44
• /
• 2007

Methods of repair welding are different to production welding for welding position, welding process, welding power source, heating methods. This study investigated proper the welding process used the welding process SMAW and GTAW in the weldment of inconel filler metals. Mechanical test showed that SMAW and GTAW process had higher mechanical properties than those of material specification. Both SMAW and GTAW welding process can appy the repair welding. In comparison, GTAW welding process had more higher mechanical properties in the weldment.

• Journal of Welding and Joining
• /
• 제33권5호
• /
• pp.47-52
• /
• 2015

In this study, it was tried to analyze the effects of welding parameters on the weld penetration and aspect ratio when a STS316L pipe was welded in a horizontal position by GTAW. Experiments were systematically designed using a L18 orthogonal array, and the effects of welding parameters were statistically analyzed by ANOVA(Analysis of Variance). The shielding gas type has the largest effect on both the penetration and aspect ratio. The welding current type and shielding gas flow rate have a little effect on the penetration, whereas the electrode tip angle has a little effect on the aspect ratio. When welded at a selected welding condition, which is composed of He shielding gas, pulse current of 300/45 A, electrode tip angle of 90o, and shielding gas flow rate of 30 l/min, the estimated interval at least 95 % confidence was $1.99{\pm}0.18mm$ for the penetration and $0.31{\pm}0.04$ for the aspect ratio. From the confirmation experiments, the average penetration and aspect ratio were well agreed with the estimation as 1.96 mm and 0.30, respectively. Additionally, the effects of the welding speed and welding current on the penetration and aspect ratio were experimented and analyzed by linear regression. The penetration was linearly increased with the decrease of the welding speed and with the increase of the welding current, but the aspect ratio showed a tendency to a little decrease with the increase of both the welding speed and current.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1992년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 19-21 Oct. 1992
• /
• pp.797-800
• /
• 1992

Much experience and knowledge is needed in welding because there are many working parameters and quantitative description is difficult. Therefore, introduction of expert system based on such data base has been required. In this study, welding heat and shape of bead was controlled by fuzzy inference with the welding condition, position error and voltage and current error of robot. For this, torch trajectory of robot was generated by modeling the working data with CAD and then welding was carried out through down loading to robot. And working error was controlled by on-line communication.

• Journal of Welding and Joining
• /
• 제22권6호
• /
• pp.43-49
• /
• 2004

In this study, a visual sensor system which can detect I-butt weld joint with height variation and includes a seam tracking algorithm was investigated. Three-dimensional position of an object can be acquired by using the method of distance measurement, i.e., an optical trigonometry which results from the spatial relations between the camera, the object and the structured light by a visible laser. Effects of laser intensity and iris number for the image quality as well as object material were investigated for the optical system design. For the image processing, a region of interest is defined from the whole image and a line image of laser is drew by using the gray level difference in the image. From the drew laser line, the weld joint can be recognized in searching the biggest point position calculated from the central difference method. Through a series of welding experiments, a good tracking performance was confirmed under GMA welding.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.352-355
• /
• 2004

Inconel 625 is useful in variety of industrial applications because of the resistance to attack in various corrosive media at temperatures from $200^{\circ}C$ to over $1090^{\circ}C$, in combination with good law- and high temperature mechanical strength. Rencently, this material is also used widely in offshore processing piping in order to extend the maintenance tenn and improve the quality of anti-corrosion. In general, high quality weldments for this material are readily produced by commonly used processes. Not all processes are applicable to this material group, Ni-alloys. Metallurgiad characterictics or the unavailability of matching, position or suitable welding processes. Nowadays, the flux cored wire is developed and applied for the better productivity in several welding position including the vertical position. in this study, the weldability and weldment characteristics of inconel 625 are considered in FCAW weld associated with the several shielding gases($80\%Ar\;+\;20\%\;CO_2,\;50\%Ar\;+\;50\%\;CO_2,\;100\%\;CO_2$) in viewpoint of welding productivity.

• Journal of Welding and Joining
• /
• 제18권3호
• /
• pp.60-67
• /
• 2000

In this study, we constructed a preview-sensing visual sensor system for weld seam tracking in GMA welding. The visual sensor consists of a CCD camera, a diode laser system with a cylindrical lens and a band-pass-filter to overcome the degrading of image due to spatters and/or arc light. To obtain weld joint position and edge points accurately from the captured image, we compared Hough transform method with central difference method. As a result, we present Hough transform method can more accurately extract the points and it can be applied to real time weld seam tracking. Image processing is carried out to extract straight lines that express laser stripe. After extracting the lines, weld joint position and edge points is determined by intersecting points of the lines. Although a spatter trace is in the image, it is possible to recognize the position of weld joint. Weld seam tracking was precisely implemented with adopting Hough transform method, and it is possible to track the weld seam in the case of offset angle is in the region of $\pm15^{\circ}$.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.23-23
• /
• 2009

우수한 용접부 품질 때문에 TIG를 이용한 오비탈 용접은 파이프 용접에 널리 사용되고 있다. 하지만 루트갭이 없고 루트페이스가 큰 맞대기 오비탈 용접의 위보기 및 경사상진자세에서는 오목한 이면비드가 형성되기 쉽지만, 이러한 문제를 극복하기 위한 연구는 희박한 실정이다. 본 연구에서는 위보기 및 경사상진자세에서 볼록한 이면비드의 형성을 연구하기위해서 용융지의 제어 방법을 적극적으로 검토하였다. 4mm 두께의 SS400 시편을 위보기 및 경사상진자세에서 각각 Bead-on-plate 용접하고, 이 때 비드성형기의 사용에 따른 비드 형상 변화를 관찰하였다. 텅스텐 전극과 비드 성형기간의 거리(Tip To Former Distance, 이하 TTFD)를 4.5mm에서 7.5mm로 1mm단위로 변경시켜 실험하였으며, TTFD가 증가할수록 위보기 및 경사상진자세에서 이면비드 높이가 감소하였으며 표면비드의 처짐이 증가하였다.

• Journal of Welding and Joining
• /
• 제30권5호
• /
• pp.22-26
• /
• 2012

Butt-joints of A6061-T6 and AZ31 plates were successfully manufactured by using a friction stir welding method. Off-set free joints and off-set joints were fabricated to investigate the effect of the tool plunge position on the mechanical properties of the joints. Hardness test, tensile test and charpy impact test was performed to evaluate the mechanical properties of the joints. Off-set condition resulted in increase of mechanical properties of the joints. The variation of the hardness distribution in the SZ was also stabilized in the off-set condition. Tensile strength of the off-set joint was about 85% against to that of the AZ31 base metal. Impact absorption energy by Charpy-Impact-Test of the off-set joint also increased by almost 2 times against to that of the AZ31 base metal.