• Safety and Health at Work
• /
• v.4 no.3
• /
• pp.123-135
• /
• 2013

Exposure to manganese (Mn) is associated with neurobehavioral effects. There is disagreement on whether commonly occurring exposures in welding, ferroalloy, and other industrial processes produce neurologically significant neurobehavioral changes representing parkinsonism. A reviewof methodological issues in the human epidemiological literature onMnidentified: (1) studies focused on idiopathic Parkinson disease without considering manganism, a parkinsonian syndrome; (2) studies with healthy worker effect bias; (3) studies with problematic statistical modeling; and (4) studies arising from case series derived from litigation. Investigations with adequate study design and exposure assessment revealed consistent neurobehavioral effects and attributable subclinical and clinical signs and symptoms of impairment. Twenty-eight studies show an exposure-response relationship between Mn and neurobehavioral effects, including 11 with continuous exposure metrics and six with three or four levels of contrasted exposure. The effects of sustained low-concentration exposures to Mn are consistent with the manifestations of early manganism, i.e., consistent with parkinsonism. This is compelling evidence thatMnis a neurotoxic chemical and there is good evidence that Mn exposures far below the current US standard of $5.0mg/m^3$ are causing impairment.

• Journal of Computational Design and Engineering
• /
• v.2 no.4
• /
• pp.248-252
• /
• 2015

Currently composite manufacturing process, such as linear friction welding plus NC machining, is the main method for the manufacturing and repairing of complex parts with integrated structure. Due to different datum position and inevitable distortion from different processes, it is important to ensure sufficient machining allowance for complex parts during the NC machining process. In this paper, a workpiece localization approach for machining allowance optimization of complex parts based on CMM inspection is developed. This technique concerns an alignment process to ensure sufficient stock allowance for the single parts as well as the whole integrated parts. The mathematical model of the constrained alignment is firstly established, and then the symmetric block solution strategy is proposed to solve the optimization model. Experiment result shows that the approach is appropriate and feasible to distribute the machining allowance for the single and whole parts for adaptive machining of complex parts.

• Journal of Practical Engineering Education
• /
• v.13 no.3
• /
• pp.461-471
• /
• 2021

This study investigated the application and satisfaction of the global industrial technology curriculum for foreign students at J University in Korea. In order to derive the global industrial technology curriculum, industry needs were analyzed, and the appropriateness of the curriculum was identified through the current status of the root industry. In order to investigate the satisfaction with the application of the global industrial technology curriculum, a questionnaire survey was conducted in the form of an in-person interview for two months from August to September 2021 for foreign students. The questionnaire surveys included general information of the subjects, the status of completion of the curriculum, questions about class satisfaction, the process of obtaining certifications, and whether or not they were employed. As a result of the study, the reasons for choosing the curriculum of the respondents were their interest in subjects related to the root industry (welding, machining, etc.) and the issuance of Korean employment and visas (E-7). The most preferred subject was welding practice at 36.8%, and in terms of subjects considered necessary, the subject of basic major terminology was the most at 29.2%. The difference in satisfaction between graduates and current students who applied the same curriculum was tested, and as a result of the analysis, it was confirmed that there was no difference in satisfaction between current students and graduates through the t test (significance level p=0.05). We believe that this study is meaningful in that it provides basic data for the domestic industrial technology curriculum for foreign students and suggests the direction of related research in a time when the existence of universities is threatened due to the decrease in the school-age population.

• Steel and Composite Structures
• /
• v.16 no.5
• /
• pp.491-506
• /
• 2014

Buckling-restrained braces (BRBs) have excellent hysteretic behavior while buckling-restrained braced frames (BRBFs) are susceptible to residual lateral deformations. To address this drawback, a novel self-centering (SC) BRB with Basalt fiber reinforced polymer (BFRP) composite tendons is presented in this work. The configuration and mechanics of proposed BFRP-SC-BRBs are first discussed. Then an 1840-mm-long BFRP-SC-BRB specimen is fabricated and tested to verify its hysteric and self-centering performance. The tested specimen has an expected flag-shaped hysteresis character, showing a distinct self-centering tendency. During the test, the residual deformation of the specimen is only about 0.6 mm. The gap between anchorage plates and welding ends of bracing tubes performs as expected with the maximum opening value 6 mm when brace is in compression. The OpenSEES software is employed to conduct numerical analysis. Experiment results are used to validate the modeling methodology. Then the proposed numerical model is used to evaluate the influence of initial prestress, tendon diameter and core plate thickness on the performance of BFRP-SC-BRBs. Results show that both the increase of initial prestress and tendon diameters can obviously improve the self-centering effect of BFRP-SC-BRBs. With the increase of core plate thickness, the energy dissipation is improved while the residual deformation is generated when the core plate strength exceeds initial prestress force.

• Journal of Fisheries and Marine Sciences Education
• /
• v.18 no.1
• /
• pp.58-64
• /
• 2006

In order to examine the effect of humidity on hydrogen embrittlement of STS 444 weld zone for boiler with dry and wet welding conditions, this paper was carried out the accelerated hydrogen osmosis test and the electrochemical Tafel polarization test. In 0.5M $H_2SO_4$ + 0.01M $As_20_3$ solution, this test is added to load of $1400kg/cm^2$ together with hydrogen osmosis by current of $50 {mA/cm^2}$ for 60 min.. The electrochemical Tafel polarization test was carried out in 0.5M $H_2SO_4$ + 0.01M $As_20_3$ solution. Therefore, the effect of humidity on hydrogen embrittlement of STS 444 was considered. The main results are as following: On the basis of hydrogen embrittlement mechanism, that is, integrated electrochemical polarization characteristics with the established mechanism of hydrogen embrittlement, the reduction rate of corrosion current density of weld zone in the wet weld condition is larger than in the dry condition. We can nondestructively predict the degree of hydrogen embrittlement of STS 444 weld zone for boiler through the reduction rate of electrochemical corrosion current density.

• Journal of the Korean institute of surface engineering
• /
• v.41 no.3
• /
• pp.109-113
• /
• 2008

High strength 7xxx series Al-Zn-Mg alloy have been investigated for using light weight automotive parts especially for bump back beam. The composition of commercial 7xxx aluminum has the Zn/Mg ratio about 3 and Cu over 2 wt%, but this composition isn't adequate for appling to automotive bump back beam due to its high resistance to extrusion and bad weldability. In this study the Zn/Mg ratio was increased for better extrusion and Cu content was reduced for better welding. With this new composition we investigated the effect of composition on the resistivity against stress corrosion cracking. As the Zn/Mg ratio is increased fracture energy obtained by slow strain rate test was decreased, which means degradation of SCC resistance. While the fracture energy was increased with Cu contents although it is below 1%, which means improvement of SCC resistance. These effects of composition change on the SCC resistivity were identified by observing the fracture surface and crack propagation.

• Journal of Fisheries and Marine Sciences Education
• /
• v.4 no.1
• /
• pp.1-15
• /
• 1992

Fishery and shipping industry are ones of the important industries for the Republic of Korea, and the education of competent technicians is a essential-important factor for the further development in these fields. To this end, curriculum for the fisheries and/or merchant marine high schools are rearranged to meet the industrial needs and social change. In this study, the existing goal of education is rearranged inclusively to meet the further development and the curriculum to realize the goal. The departments are reorganized into nine ones by establishing new two. They are Department of Refrigeration Mechanical Engineering and of Automated-ship Operation. Four departments of existing seven-Department of Fish Aquaculture, of Fish Processing, of Marine Engine and of Marine Communication-are renamed into Department of Aquaculture, of Food Processing, of Power Mechanical Engineering and of Electronic Communication respectively. The remaining three departments- Department of Fishing Technology, of Self-managing Fisheries and of Navigation-are unchanged. The specialized subjects are revised as follows; (1) The existing seven subjects especially prepared for the fisheries and/or merchant marine high schools are changed into the common subjects for all the vocational high schools. They are Food Science, Food Hygiene, Food Processing Machinery, Air-conditioning Facilities, Welding and Piping, Communication Law and Introduction to Computer. (2) Two subjects are newly established: Refrigeration Mechanical Engineering and Automated-ship Operation. (3) Four subjects are disused : Sea Training, Fisheries Law, Canned Food and Practice in Communication. (4) Introduction to ship, to Marine Engine and to Marine Communication are merged into Introduction to ship. (5) The compulsory major subject is fixed as Introduction to Fisheries for the fisheries high schools and Introduction to shipping Industry for the merchant marine high schools.

• Journal of the Korean Society for Heat Treatment
• /
• v.12 no.4
• /
• pp.303-312
• /
• 1999

An investigation of the CrMoV rotor steel weldment which experienced by cyclic thermal aging heat treatment and as-received condition was performed. This evaluation was carried out to confirm whether this type of weldment is appropriate for the service environment in terms of microstructural examinations, microhardness measurements and tensile tests. The cyclic thermal aging heat treatment, containing continuous heating and cooling thermal cycle was programmed to simulate the real rotor service condition. The heat treatment was performed for 40 cycles(5920hrs). The results indicated that the weldment was composed of 4 different regions such as heat affected zone of the base metal, butter weld(initial weld), full thickness weld(final weld) and the base metal. The double welding process was applied to eliminate the susceptibility of reheat cracking at heat affected zone of base metal. The grain refinement at the HAZ due to the welding process could reduce the possibility of cracking susceptibility, but its tensile properties was appeared to be low due to the weld metal in as-received condition. The benefit effect, grain refinement was extended with carbides coarsening during the cyclic thermal aging heat treatment. However the poor mechanical properties of the weldment was more degraded as undergoing the heat treatment.

• Fashion & Textile Research Journal
• /
• v.15 no.2
• /
• pp.294-301
• /
• 2013

Sustainable fashion & textile is more than eco fashion & textile with the concepts for the next generation's happiness, prosumer value, and community responsibility. This study considers methods to enhance fashion and textile industry sustainability in accordance to clothing types (material, product life and washing properties) and to investigate company strategies. Company strategies are of redesign with stock, volunteering & measuring trash amount, participation by evaluation stores, clerk environment education, hiring QC specialist and reinforcing partnerships. For the case of daily innerwear, throwing away and recycling is more efficient for the environment than laundering in the consumer use stage; subsequently, we recommend the use of polypropylene fiber (a cheap and an eco-friendly material) for this item that can be recycled and reformed after use. For the case of single layer clothing (such as sportswear, blouse or pants) we recommend the use of thermoplastic materials with welding or fuse assembling technology instead of a sewing method of seams as well as the recycle design that is simply melted and reformed into new clothing without an after use dissembling process. Secondhand use or resale is suitable for denim/jean items if the clothing has a storytelling or private history tag. Lastly, module-type jacket or coat shows the variety of styles with one clothing worn w/o collar or sleeve details and changed into vest/coat; in addition, it is possible to add or partly tear off some jacket/coat fibers of the felt material to reform it into a new design.

• Journal of Practical Engineering Education
• /
• v.14 no.1
• /
• pp.127-136
• /
• 2022

As manufacturing items have changed in various ways, changes in the mass production of small-scale small-scale production of multiple varieties have become commonplace. As a result, the method of the manufacturing site has also changed, and the "smart factory," which emphasizes the production efficiency aspect using automation lines and big data of factories, is in the spotlight according to the global market economy. The introduction performance of smart factories has a positive effect in terms of production efficiency and is drawing a steep upward curve. In addition to the positive aspects, the aspect that needs to be supplemented in the future is the support and cooperation of specialized smart equipment suppliers, but education on standardized smart factories and the relocation of existing manpower, education, evaluation, and creative production that robots cannot replace Various support measures are also needed for activities. In addition, continuous management and systematic education are required to enter the upper stage. Through the case of companies that have built smart factories, it is intended to emphasize the need for proper use of manpower and support management for settlement and maintenance after introduction and continuous on-the-job training through the comparison of productivity before and after introduction to ensure the effect continues.