• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.997-1003
• /
• 2005

Laser welding of dissimilar metals has been widely used to improve a wear resistance and a corrosion resistance of the industrial parts. The objective of this research works is to investigate the influence of the process parameters, such as the welding for SM45C and STS304 with CW Nd:YAG lasers. The bead-on-plate welding tests are carried out for several combinations of the experimental conditions. In order to quantitatively examine the characteristics of the dissimilar welding, the welding qualify of the cut section, stain-stress behavior and the hardness of the welded part are investigated. From the results of the investigation, it has been shown that the optimal welding condition without defects in the vicinity of the welded area and with a good welding quality is 1600W of the laser power, 0.85m/min of welding speed and 4m/min of pressure for shielding gas.

• Journal of Ocean Engineering and Technology
• /
• v.21 no.3 s.76
• /
• pp.71-76
• /
• 2007

Recently, many industries have been employing the application of laser beam welding, due to the resulting high welding quality, such as smaller width of melting and heat affective zone, smaller welding deformation, and fine grains of weldment, compared to arc welding. However, in order to appropriately utilize this welding process with steel structure, the characteristics of welding residual stresses and fracture toughness in welded joints are to be investigated for reliability. Therefore, in this study, the mechanical properties of weldments by arc and laser welding are investigated using FEM to confirm the weldability of laser welding to the general structural steel (HT50). The Charpy impact test and 3-points bending CTOD test are carried out in the range of temperatures between $-60^{\circ}C\;and\;20^{\circ}C$, in order to understand the effect on the fracture toughness of weldments. From the research results, it has been found that the maximum residual stress appears at the center of plate thickness, and that the fracture toughness is influenced by strength mis-match.

• Journal of Welding and Joining
• /
• v.34 no.3
• /
• pp.1-5
• /
• 2016

At present, FSW(friction stir welding) process is being considered as an actual way for production of various industrial products. However FSW process involves high temperature and load on the tool during welding. These are make a difference between FSW machine and general machine tools. From this reason, development of FSW machine needs very careful consideration on stiffness of machine structure, spindle and moving axis including machine control system. In this study authors investigate on the trends of technology development of FSW machine in order to share the information for more extension of FSW technology with related researchers and engineers.

• Journal of Welding and Joining
• /
• v.35 no.1
• /
• pp.49-54
• /
• 2017

In this study, the volumetric heat source in electron beam welding (EBW) is modeled through finite element method taking advantage of ABAQUS software package. Since this welding method is being applied in plates with different thicknesses and also considering that residual stresses reduce the strength of these weldments, the effect of thickness in the distribution and magnitude of residual stresses after welding is studied. Regarding the vast application of Inconel 706 super-alloy in aerospace industries, this material was selected in the current research. In order to validate the finite element model, the obtained results were compared to those of other researchers in this area, and good agreement was observed. The simulation results revealed that increase in the plate thickness leads to increase in the residual stresses. In addition heat treatment in the base metal (before welding) increases the residual stresses significantly.

• Journal of Ocean Engineering and Technology
• /
• v.1 no.1
• /
• pp.120-126
• /
• 1987

In this paper, the optimizing investigation of characteristics of underwater welding by a gravity type arc welding process is experimentally carried out by using the .phi. 4mm ilmenite type of domestic coated welding electrodes for welding the domestic marine structural steel plates of 8mm thickness in order to develop the underwater welding techniques in practical use, resulting in the quantitative analysis possibility for the relationship between the mechanical propernical properties of underwater welded joint HAZ and the welding heat input.

• Journal of the Korean Society of Industry Convergence
• /
• v.11 no.2
• /
• pp.83-91
• /
• 2008

GMAW(Gas Metal Arc Welding) processes are usually used in industrial side in order to get its high productivity. But those are only adopted in the semi-automated welding equipment because of a lot of welding spatters. Many industrial robot actually percents from being engaged in the welding processes. The welding spatter problem of causes blocking them being a fully automated welding process.This study was carried out to investigate the optimal conditions for minimizing welding spatter generation at GMAW robot. The spatter can be significantly reduced below 2% of welding spatter generation at the following conditions ; First, below 18V at the wire-feed rate 2.0mm/min Second, below 23V at the wire-feed rate 3.6mm/min Third, below 24V at the wire-feed rate 5.5mm/min.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.433-438
• /
• 2002

The education, examination and qualification systems around the world are now changing rapidly and unifying as one system. The Korean national system should be harmonious with this international tendency, in order to overcome the high degree of international economic competition. In this article, the current state of the international and national systems are critically compared and discussed with the intention of proposing improvements to the Korean national system. The Korean Welding Society has revamped its system so that its certificates might be recognized by the welding institutions in foreign countries such as the European Welding Federation (EWF) and still be recognized by the Korean Government. Their desire to join the system of International Institute of Welding (IIW) was also a factor in the restructuring.

• Journal of Welding and Joining
• /
• v.20 no.1
• /
• pp.83-90
• /
• 2002

Metal Transfer in gas metal arc (GMA) welding is a complex phenomenon affected by many parameters of the welding conditions and material properties. In this research, the correlation equation between the welding condition and detaching droplet size and detaching velocity in GMA welding was studied via recession analysis on the results of numerical analysis using the volume-of-fluid (VOF) method. Welding parameters and material properties were grouped into three dimensionless numbers and detaching droplet size was expressed as the function of them. Second order and exponential multi-variable correlation forms were assumed, and the coefficients of these equations were calculated for globular and spray modes as well as entire transfer modes. Applying correlation equation into available experimental data, it shows good agreement.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.46.6-46
• /
• 2001

A servo gun welding system having a AC servo motor and a PC control system is presented for the improvement of quality control in the spot welding. The spot welding process is composed of the press stage, the weld stage, and the hold stage. The changes of gun press forces according to three stages in the spot welding process are controlled and measured through the load cell in order to know the influence on the welding quality. The relation between the measured force changes according to three stages and welding qualities is also implemented on the multilayer perceptrons, one of supervised learning method of neural network, which are powerful for realization of complex mapping characteristics. The estimated results and ...

• International Journal of Korean Welding Society
• /
• v.4 no.1
• /
• pp.10-14
• /
• 2004

In this paper, a study on the residual stress of plate with longitudinal stiffeners is explained in terms of the welding sequences. In order to verify the results of numerical analysis, the hole drilling method (HDM) is performed, to measuring the residual stresses of the test plates in $CO_2$ Flux Cored Arc Welding (FCAW) under various welding conditions. The non-linear transient analysis technique for the numerical analysis in a large and complicate structure is considered. The residual stress of plate in consideration of the welding sequences and directions is evaluated by some numerical simulations and also by experiments. Comparison of numerical analysis results with experimental data shows the accuracy and validity of the proposed method.