• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.235-238
• /
• 2009

To study the relationship between spark ignition and the gap in the nano-scale region, the electric potential was applied to between a Pt-Ir tip and a gold substrate. The tip was sharpened by electro-chemical etching process in the solution of $CaCl_2;H_2O$ and acetone. The radius of tip was measured to be around 200nm and attached to the scanning probe microscope to control the gap between the tip and the substrate. The electric potential of 10V to 80V was applied to initialize the spark. The gaps and the current profile were measured to analyze the characteristics of spark ignition. A spark sustaining time was measured to be between 50ns and 200ns depending on the applied electric potential and the gap between the electrodes. The continuous electric discharge was successfully sustained up to 1 second of spark or arc time. The developed process can be applicable to the micro-scale fabrication of automotive sensors as a similar concept of GTAW.

• 전기의세계
• /
• 제21권4호
• /
• pp.27-38
• /
• 1972

This paper discusses the characteristics about the ignition of D.C. main discharge is a plasma jet generator, manufactured for trial as non-transferred type, when the electrical energy appropriate to the ignition is supplied to the gap between the electrodes by using advance discharge of attenuating high frequency voltage generated by a high frequency oscillator with mercury spark gap. These characteristics are under the influences of (a) the length of mercury gap in high frequency oscillator and the quantity of hydrogen flow supplied to it, (b) the condenser capacity of the high frequency oscillator circuit, (c) the length of plasma jet torch in D.C. main discharge circuit and the quantity of argon flow supplied to it, (d) the circuit constants of D.C. main discharge circuit. The results for these characteristics, obtained by this research, are considered to be helpful to the designs for the ignition of a plasma jet as well as the welding arc stabilizer by high frequency discharge and the high frequency arc welder.

• 한국해양공학회지
• /
• 제28권4호
• /
• pp.356-362
• /
• 2014

Wear and corrosion of the engine parts surrounded with combustion chamber is more serious compared to the other parts of the engine because temperature of the exhaust gas in a combustion chamber is getting higher and higher with increasing of using the heavy oil of low quality. Therefore, an optimum repair weldment as well as an available choice of the base metal for these parts are very important to prolong their lifetime in a economical point of view. It reported that there was an experimental result for repair weldment on the forged steel which would be generally used with piston crown material, however, it is considered that there is no study for the repair weldment on the cast steel of piston crown material. In this study, four types of electrodes such as 1.25Cr-0.5Mo, 0.5Mo Inconel 625 and 718 were welded with SMAW and GTAW methods on the cast steel which would be generally used with piston crown material. And the corrosion properties of weld metal, heat affected zone and base metal were investigated using electrochemical methods such as measurement of corrosion potential, anodic polarization curves, cyclic voltammogram and impedance etc. in 35% $H_2SO_4$ solution. In the cases of Inconel 625, 718, the weld metals and base metals exhibited the best and worst corrosion resistance respectively, however, 1.25Cr-0.5Mo and 0.5Mo indicated that corrosion resistance of the base metal was better than the weld metal. And the weld metal welded with electrodes of Inconel 625 revealed the best corrosion resistance among the electrodes, and Inconel 718 followed the Inconel 625. Hardness relatively also indicated higher value in the weld metal compared to heat affected zone and base metal. In particular, Inconel 718 indicated the highest value of hardness compared to other electrodes in the heat affected zone.

• 한국정밀공학회지
• /
• 제3권3호
• /
• pp.13-21
• /
• 1986

Turning property of metal is affected by the cutting condition, tool geome- try and cutting material. But the turning property of welded material is not welknown. Welded structures usually contain nonhomogeneity, defects and resi- dual stresses due to differential contraction between welded metal and base metal. In this paper, authors conducted the experimental test on the turning property, by changing turning condition and welding electrodes of the welded specimens. The results obtained in these experimental tests are as follows; (1) Within the limit of this experimental test, the cutting force of the weld zone is bigger than that of base metal, and this phenomena is caused by the different mechanical property of the weld zone. The range of the variation of cutting force in the weld zone is caused by the nonhomogeneity of the weld zone, respectively. (2) The surface roughness follows the general characteristic of the effect of cutting condition on the surface roughness and the surface roughness of the weld zone shows coarse surface comparing with that of the base metal. (3) The specimen welded by the electrode E4301, shows worse cutting property than that of E4361 and E4313.

• 전기의세계
• /
• 제24권1호
• /
• pp.75-85
• /
• 1975

In order to develop the commercial frequency (60Hz) plasma torch of small capacity for material cutting, welding and other industrial heating, the A.C plasma jet generator of non-transfered type is made domestically and the electrode configurations of plasma torch are composed of two kinds of electrodes W-C and W-Cu, combined by thermal emission and field emission electrode materials. In this paper, the characteristics of input power, thermal efficiency, electrode consumption, the flame and forms of arc voltage and arc current for A.C plasma torch are investigated in relation to such variables as arc current, argon flow and magnetic field intensity to obtain the basic design data necessary to A.C plasma jet generator. The result are as follows; (1)The input power, thermal efficiency and electrode consumption are influenced greatly by argon flow, magnetic field intensity and nozzle materials. (2)A.C arc voltage and current are non-symmetrial, involving D.C Component. Due to this current of D.C Component, transformer core is saturated and a large abnormal current flows into the primary winding coil. In order to prevent this abnormal current flow, a condenser must be connected in series to the main discharge circuit. (3)The stability and sharpness of jet flame are improved more in the torch of W-C electrode configuration than in the torch of W-Cu electrode configuration.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2010년도 춘계학술발표대회 초록집
• /
• pp.81-81
• /
• 2010

전자 패키징은 미세화, 경량화, 저가화를 지향하고 신뢰성의 향상을 위해 발전해 왔다. 이러한 경향은 전자부품 자체의 성능 향상 뿐 아니라 전자부품을 장착, 고정할 수 있게 하는 인쇄회로 기판(PCB : Printed Circuit Board)의 성능에 많은 관심을 가지게 되었다. 전기적 신호의 손실을 줄이기 위해 전기, 전자 산업체에서는 가볍고 굴곡성이 우수한 연성인쇄회로기판(FPCB : Flexible PCB)과 가격이 싸고 신뢰성이 입증된 경성인쇄회로기판(RPCB : Rigid PCB)이 그 대상이다. 본 논문에서는 이 PCB중에서도 RPCB와 FPCB간의 열압착 방식으로 접합 시 전극간의 접합 양상을 보았다. 이 열압착 방식은 기존에 PCB를 접합하는데 사용하고 있는 connector를 이용한 체결법을 대체하는 기술로써 솔더를 중간층(interlayer)로 이용하여 열과 압력으로 접합하는 방식이다. 이 방식을 connector를 사용하는 방식에 비해 그 부피가 작고 I/O개수에 크게 영향 받지 않으며 자동화 공정이 쉬운 장점을 가지고 있다. 접합의 대상 중 RPCB의 경우는 무전해 니켈 금도금(ENIG : Electroless Nickle Immersion Gold)로 제작하였으며 FPCB의 경우는 ENIG와 유기보호피막(OSP : Organic solderability preservation) 처리하였다. 실험에 사용한 PCB는 $300\;{\mu}m$ pitch의 미세피치이며 솔더의 조성은 Sn-3.0Ag-0.5Cu (in wt%)과 Sn-3.0Ag (in wt%)를 사용하였다. 접합 온도와 접합 시간 그리고 접합 압력에 따라 최적의 접합 조건을 도출하였다. 접합 강도는 $90^{\circ}$ Peel Test를 통해서 측정하였으며 접합면 및 파괴면은 SEM과 EDS를 통하여 분석하였다.

• Composites Research
• /
• 제19권2호
• /
• pp.28-34
• /
• 2006

고온자전합성법과 스파크 플라즈마 소결법으로 여러 가지 $TiB_2$ 함유량을 갖는 $Cu-TiB_2$ 금속복합재료를 제조하였다. 점용접 전극과 미끄럼 접촉재로 사용하기 위해 인장특성, 경도, 마모저항 등의 물성치를 조사하였다. 강화재의 형상, 크기, 부피분율 등에 의해 복합재료의 특성이 달라지므로 유효물성치를 예측하기 위한 모델링이 필수적이다. 유한요소해석결과 유효탄성 계수가 실험치와 일치하는 것을 확인하였고 Eshelby 모델, Mori-Tanaka의 평균장 이론이 결합된 Eshelby 모델, 혼합법칙 등으로 복합재료의 탄성계수를 예측한 결과 Mori-Tanaka의 평균장 이론이 결합된 Eshelby 모델이 실험치를 사장 잘 묘사하는 것으로 나타났다.