• Journal of Welding and Joining
• /
• v.16 no.2
• /
• pp.100-110
• /
• 1998

In this paper, the laser weldability of thin gage steels for automobile application is discussed. Welding was carried out with a high power carbon dioxide laser system, and the laser energy was concentrated through a plano-convex lens. Test results showed that the joint gap in the butt welding proved to be one of the critical conditions for an acceptable weld. In the case where the ratio of the gap clearance to the material thickness was slightly bigger than optimal value, the weld strength was reduced showing weld metal fracture. It was possible to obtained a weld penetration ratio of 0.91 when the vertical offset ratio was controlled to be 0.4 or smaller. Results also demonstrated that the weld strength of the lap joint was influenced by travel speed. At the travel speeds lower than 37 mm/s, the weld strength indicated higher value than that of class A recommendation strength of a resistance spot weld based on the KS code. It was clear that the complicated effect of specimen alignment should be considered so as to make a sound weld with high integrity when the laser process was applied to the long weld line.

• Journal of the Society of Naval Architects of Korea
• /
• v.44 no.5
• /
• pp.496-503
• /
• 2007

Although weld-induced deformation is inevitable in shipbuilding, it is important to reduce it as low as possible during fabrication for a more efficient production of ships' blocks. The weld-induced deformation is more serious in thin plates than in thick plates because heat affect zone of thin plates is wider than that of thick plates, and in addition internal and external constraints much more influence upon weld-induced deformation of thin plates. This paper deals with the application of the mechanical tensioning method to butt weld of thin plates to reduce the transverse and longitudinal deformation. in order to investigate the quantitative effect of tensioning method upon the reduction of angular deformation and shrinkage in longitudinal and transverse direction of weld line, butt welding test have been carried out for several thin plate specimens with varying plate thickness and magnitude of tensile load. Numerical simulation has been also carried out to compare the weld-induced deformation and residual stress. From the present study, it has been found that the tensioning method is very effective on reduction of weld-induced residual stress as well as weld-induced deformation.

• Journal of Ocean Engineering and Technology
• /
• v.22 no.1
• /
• pp.64-69
• /
• 2008

As it has been well appreciated from the viewpoint of efficiency, The weld-induced deformation control is one of the most important issues in marine structure production. In the case of thin plate block, weld-induced deformation is more serious than in the case of relatively thick plate block. The heat affect zone of thin plates is wider than that of thick plates with the same heat input. Among weld-induced deformations, the buckling deformation by the shrinkage and residual stress in the weld line direction is one of the most serious deformation types. This paper is concerned with controlling buckling deformations for the thin plate fillet welds, by using the tensioning method. A numerical analysis was carried out to illustrate several dominant buckling modes due to compressive residual stress in the fillet weldsof thin plates. Then, weld tests were carried out for 20 specimens with varying plate thickness, and with different magnitudes and directions for the tension load. The results graphically represented to shaw the effect of the tensioning method in reducing the weld-induced deformation. From the present findings, it was seen that the tensioning method is a useful way to control weld-induced deformations in the fillet welds of thin plates.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.9
• /
• pp.5419-5424
• /
• 2014

A weld scallop is a small quadrant or half circle type hole installed in the weld line cross area for easy welding operation. Many types of T-bars with a scallop can be welded in a block assembly stage in shipbuilding. The difficulties arise from the fact that scallops are to be filled by build-up welding after welding of the cross line is complete. In this study, a non-scallop block joint welding method was developed using special type CBM (ceramic backing material). The wedge shaped CBM was devised to insert a CBM into just the V groove of weld line cross area without weld scallop. A saw-toothed shape was adopted for easy cutting of the unnecessary part in the CBM fitting process. The applicability of the developed method was verified through welding experiments based on the yard welding conditions.

• Journal of Welding and Joining
• /
• v.22 no.6
• /
• pp.43-49
• /
• 2004

In this study, a visual sensor system which can detect I-butt weld joint with height variation and includes a seam tracking algorithm was investigated. Three-dimensional position of an object can be acquired by using the method of distance measurement, i.e., an optical trigonometry which results from the spatial relations between the camera, the object and the structured light by a visible laser. Effects of laser intensity and iris number for the image quality as well as object material were investigated for the optical system design. For the image processing, a region of interest is defined from the whole image and a line image of laser is drew by using the gray level difference in the image. From the drew laser line, the weld joint can be recognized in searching the biggest point position calculated from the central difference method. Through a series of welding experiments, a good tracking performance was confirmed under GMA welding.

• Transactions of Materials Processing
• /
• v.7 no.4
• /
• pp.354-363
• /
• 1998

In order to analyze the stretch forming characteristics of tailored blanks, laser welded blanks of different thickness and strength combinations were prepared and stretching tests were done. The stretching formability of laser welded blanks was reduced as increasing the deformation restraining force ($strength{\times}thickness$) ratio between two welded sheets. Weld line movement was attributed to strain concentration at weaker sheets and resulted in fracture at weaker sid, so that fracture could be predicted by the forming limit of the weak sheet. In the case of a welded blank with the similar deformation restraining force rations between two welded sheets, crack occurred at weld and its forming limit was about 15% less than the base sheet. The effects of lubrication and weld line position on stretch-ing formability were also investigated by experiments. Lower friction did not always give better formability for tailored blanks. Stretching formability was observed to be improved as increasing the area of weak sheet.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.729-733
• /
• 1997

Due to the variety of disturbance, it is not ease to accomplish the in-process detection of weld line with non-contact sensor. To get around this difficulties problem develop an automatic seam tracking weld system, the reliable signal processing algorithm has been recommanded. In this research, laser displacement sensor is applied as a seam finder in the automatic tracking system. The sensor is controlled by a dc servo motor which is mounted at X-Y moving table. X-Y moving table manipulated by an ac servo motor controls the position and velocity of the welding torch. First, X-Y table moves to Y-axis to search the welding joint feature before starting the welding, and welding joint is from the scanning data and weighting factor for each other. Second, weld line is determined using proposed signal processing algorithm during welding process. Form the experimental results, we could see the possibility that laser displacement sensor with procesed algorithm can be used as a seam finder in welding process under the severe noise (spatter,arc light etc.) condition

• Laser Solutions
• /
• v.2 no.1
• /
• pp.30-37
• /
• 1999

Laser-welded Tailored Blank is the hottest thing in many automobile companies. But they demand on weld quality, reproducibility, and formability. So it is the great problem of automation of laser welding process. Therefore, it is requested to construct on-line process monitoring system on high accuracy. The light which is emitted from plasma and spatter in laser welding was detected by photo-diodes. It was found that the light intensity depends on welding speed. laser power, and flow rate of assist gas. The relationship between the plasma and spatter and the weld quality can be used for on-line laser weld monitoring systems.

• Laser Solutions
• /
• v.13 no.3
• /
• pp.7-12
• /
• 2010

In this study, laser welding of aluminum AA5182 with AA5356 filler wire was carried out and the formability of the weld joint was evaluated through Erichsen test according to laser power, welding speed and wire feed rate. Fracture was occurred in both directions, perpendicular and parallel to the weld line at 0.75 of Erichsen ratio. Second order Regression model to estimate Erichsen ratio with experimental variables was proposed and the performance of model was evaluated with F-test and average error rate.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.1028-1033
• /
• 1991

This paper describes the design of a neural network estimator to estimate weld pool sizes for on-line use of quality monitoring and control in GMA welding processes. The estimator utilizes surface temperatures measured at various points on the top surface of the weldment as its input. The main task of the neural net is to realize the mapping characteristics from the point temperatures to the weld pool sizes through training, A series of bead-on plate welding experiments were performed to assess the performance of the neural estimator.