• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.7-10
• /
• 2007

In case of large steel water pipe, it have been observed that its fracture mostly occurs due to the complicated outside fatigue load on the pipe in the underground. It is also well known that its damage and leakage happen mainly in a weld zone. In this study we evaluated the fatigue characteristics based on size effect and residual stress by comparing the test results on the standard specimen collected from real pipe with those on full scale pipe.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.3
• /
• pp.181-189
• /
• 2001

For the Tailor Welded Blank sheet used fur automobile body panel, the characteristics of fatigue crack propagation behavior were studied. The thickness of specimen was machined to be same (0.9+0.9mm) and different (0.9+2.0mm). As a base test, mechanical properties around welding zone were examined. The results indicated that there were no significant decreases in mechanical properties, but hardness around welding bead is 2.3 times greater than base material. The crack propagation rate was noticeably decreased around welding line and rapidly increased as it passed by welding line. Reviewing the shape of the crack propagation, crack width around welding line was wide around the welding zone due to retardation of crack growth, but it became narrow passing welding line due to decreased toughness. Elasto-Plastic analysis was performed by finite element analysis fur explaining the test results.

• Journal of the Society of Naval Architects of Korea
• /
• v.48 no.5
• /
• pp.473-478
• /
• 2011

Welding process generates distortion and residual stress in the weldment due to rapid heating and cooling. Welding distortion and residual stress in the welded structure result in many troubles such as dimensional inaccuracies in assembling and safety problem during service. The accurate prediction of welding residual stress is thus very important to improve the quality of weldment and find the way to reduce itself. This paper presents the simulation of welding-induced residual stress analysis to examine the cause of cracking in the SUS-overlay welding specimen at FPSO Moon Pool structure.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.378-383
• /
• 2002

In previous study, the decrease and recovery of total stiffness in welded structure was discussed on the basis of experimental examination through tensile loading and unloading test of welded specimen. The recovery of structure stiffness was caused by the release of welding residual stress through mechanical loading. In this study, analysis model that is indispensable for the effective application of MSR method was established on the basis of test and measurement result. Thermal elasto-plastic analysis for welding process was performed by non-coupled analysis. Analysis results of welding process were transfer to elasto-plastic model for tensile loading & unloading by restart technique. In elasto-plastic analysis model for mechanical loading & unloading, hardening appearance of weld metal was considered by rezoning technique and tying technique was used for JIG condition of test machine.

• International Journal of Ocean Engineering and Technology Speciallssue:Selected Papers
• /
• v.6 no.1
• /
• pp.75-81
• /
• 2003

Underwater wet arc welds were experimentally performed on the KR-RA steel plate as base metal by using four different types of flux coated electrodes: KT33, UWEE, UWCS, and TN20. UWEE, the individually designed flux coated underwater electrode, had good operability when compared with other domestic terrestrial electrodes, and imported goods. The hardness value and the portion of martensite of HAZ were increased, by using a rapid cooling rate, Mechanical properties were also examined experimentally with a multi-pass butt-welding specimen test. The individually designed flux coated electrode UWEE could be used in practice for underwater wet welds.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.6 no.1
• /
• pp.20-26
• /
• 2007

In this study, fatigue strength of load-carrying cruciform fillet welded joints were evaluated using a new method proposed by Yamada, for geometric or structural stress in welded joint, that is, one-millimeter stress below the surface in the direction corresponding to the expected crack path. Validity of the method is verified by analyzing fatigue test results for load-carrying cruciform welded specimens has different size of weld toe radius, leg length and plate thickness reported in literature. Structural stress concentration factor for 1mm below the surface was calculated by finite element analysis for each specimen respectively. When compared to the basic fatigue resistance curve offered by BS7608, the one-millimeter stress method shows conservative evaluation for load-carrying cruciform fillet welded joints.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.4
• /
• pp.662-670
• /
• 2001

We evaluate the effectiveness and validity of J(sub)e, which comprehensively describes the effects of specimen geometry and loading type, in predicting the fatigue life of auto seat belt anchor panel. We first simplify the heat affected zone model to reduce the number of finite elements. We then establish finite element models reflecting the actual overload behavior of 3 types of seat belt anchor specimens. Using finite element models elaborately established, we obtain the effective crack driving parameter J(sub)e composed of its ductility-dependent modal components. It is confirmed that the J(sub)e concept successfully predicts the fatigue life of multi-spot welded panel structures represented by auto seat belt anchors here.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.9
• /
• pp.707-712
• /
• 2008

The fatigue characteristics of a material or a structure are generally derived from fatigue tests of standard specimens. However, test results of standard specimens are different from those of real structures or components. Therefore, to calculate more accurate fatigue life, the geometrical effect and surface condition must be considered by comparing test results of standard specimens with those of real structures or components. Thus the object of this paper is to evaluate the fatigue characteristics of a real waterwork pipe. Also, to evaluate fatigue characteristic based on life distribution, the statistical fatigue characteristics were analyzed by the normal distribution and related data of P-S-N curve.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1996.10a
• /
• pp.194-197
• /
• 1996

The high-strength aluminum alloy 7075-T651 was used to observe the fatigue-crack-propagation behavior for the various stress ratios with constant amplitude loading and thus to predict the fatigue life. With a chevron notch in the specimen the fatigue-crack-propagation behavior of through crack was investigated. Crack propagation behavior of through crack in the depth direction and crack growth of weldments were experimentally studied. Base material heat affected zone and weld material were considered in the fracture of weldments. The change of crack-propagation length with respect to several parameters such as stress intensity factor range(ΔK) effective stress intensity factor range(ΔKeff)ration of effective stress intensity factor range(U) stress intensity factor of crack opening point(K op) maximum stress intensity factor(K max) and number of cycles(Nf)was determined. The crack length of through crack of weldments was 2.4mm and the remaining part was a base material. The experiment was accomplished by making the crack propagate near the base material.

• Proceedings of the KWS Conference
• /
• 2006.05a
• /
• pp.71-73
• /
• 2006

Magnesium alloys are becoming important material for light weight car body, due to their low specific density but high specific strength. However they have a poor weldability, caused high oxidization tendency and low vapor temperature. In this study, the laser welding performance of magnesium alloys was investigated for automobile application. The materials were rolled magnesium alloy sheet contains 3%Al and 1%Zn. To evaluate the weldability, we examined the appearance of welding bead. The mechanical property was measured for welded specimen by tensile test. And formability was checked with the Erichsen tester. For the results, the performance of weld in laser welding was enough for press forming such as car body. But it was recommended to use filler wire for reduce the under fill.