• Journal of Ocean Engineering and Technology
• /
• v.17 no.3 s.52
• /
• pp.27-32
• /
• 2003

The welding distortion of a hull structure in the shipbuilding industry is inevitable at each assembly stage. The geometric inaccuracy caused by the distortion tends to preclude the introduction of automation and mechanization. Thus, additional man-hours are needed for the adjusting work in the assembly stage. To overcome this problem, a distortion control method should be applied. For this purpose, it is necessary to develop an accurate prediction method that can explicitly account for the influence of various factors on the welding distortion. In order to minimize the weld-induced residual deformation, this paper proposes the optimum welding sequence as a method for distortion control. The validity of this method has been substantiated by a number of numerical simulations and experiments.

• Journal of Ship and Ocean Technology
• /
• v.11 no.3
• /
• pp.14-23
• /
• 2007

Welding processes cause undesirable problems, such as residual stresses and deformations due to the thermal loads imposed by local heating, melting, and cooling processes. This paper presents a computational modeling technique to simulate the Gas Metal Arc Welding (GMAW) process, emphasizing the effect of the melting bead on the residual stress distribution. Both a three-bar analogy and a three-dimensional thermo-mechanical finite element analysis are carried out in order to explain the effect. Element (de)activation, enthalpy, and adjustment of the reference temperature of thermal strain are considered with respect to the effect of the weld filler metal added to the base metal during a thermo-elastic-plastic analysis. Stress distributions obtained by the present study are compared with measured values and available data from other studies. The effect of the melting bead on the residual stress distribution is discussed and demonstrated.

• Journal of Welding and Joining
• /
• v.15 no.3
• /
• pp.109-117
• /
• 1997

The temperature gradient in weldment changes the transit time and distorts the direction of the ultrasound beam to the higher temperature regions due to the lower sound speed in the hotter regions of the weldment. This paper describes a ray-tracing method for calculating the effects of temperature gradients on ultrasonic propagation in fillet arc weldig. In the method, weldment is conceptually devided into a number of layers and the refraction and sound speed at each layer is calculated using the temperature which calculated from analytical solution. Calculating the time and location of echoes arrived from various interfaces around a molten weld pool determines the optimum location of ultrasonic transducers and the correct position of flaws.

• Proceedings of the KWS Conference
• /
• 1996.10a
• /
• pp.148-152
• /
• 1996

A transient two-dimensional (2D) model was developed for investigating the heat and fluid flow in old pools and determining velocity profile and temperature distribution for the Gas Metal Arc (GMA) welding process. The mathematical formulation deals with the driving farces (electromagnetic, buoyancy, surface tension and plasma drag forces) as well as energy exchange between the molten filler metal droplet and weld pools. A general thermofluid-mechanics computer program, PHOENICS, was employed to numerically solve the governing equation with the associated source terms. The results of computation have shown that the electromagnetic and surface tension farces as will as the molten filler metal droplet have major influence in shaping the weld pool geometry.

• Proceedings of the KWS Conference
• /
• 2005.06a
• /
• pp.97-99
• /
• 2005

Laser arc hybrid process is actively researched as a new welding method since it has several advantages by the combination of laser beam and electric arc. By the coupling of two different heat sources, laser and arc mutually assist and influence. High power laser can make the deep keyhole and arc plasma can form the large bead shape. In this paper the effect of two different heat sources to weld bead are investigated and as a result of analysis, it is shown that the lower part of keyhole is heated by laser and the upper part of weld pool is dominantly heated by arc.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.4
• /
• pp.570-577
• /
• 2008

Magnesium alloys are potentially useful as structural materials due to higher strength/weight ratio, heat conductivity and recyclability compared to other alloys. These alloys have attracted the interest of modern manufacturing such as the automobile, computer, communication and consumer electronic appliances industries. Hence welding techniques are required to be developed for these applications. Laser are known to be an excellent tool for them. This paper presents the laser weldability of AZ31 magnesium alloy with CW Nd:YAG laser. The low viscosity and surface tension of the melt pool make magnesium more difficult to weld than steel. As a result of this study, optimal process parameters could be obtained without weld defects. Also it was certain that cutting methods had influence on butt weldability.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.13 no.1
• /
• pp.707-717
• /
• 2021

To the date, shipbuilding companies have applied shop primer coating which protects the steel surface from global oxidization in environment. Proper shop primer requires either anti-corrosion ability during construction or anti-porosity ability during welding, and those properties contradict to each other. This report tried to derive an optimizing parameter on these conflicting properties to select a proper shop primer. First, sufficient amounts of the natural salt spray tests were carried out to achieve a series of data for the anti-corrosion ability. Second, lots of T-joint fillet welding test were performed to evaluate the trapped porosity formed in the weld pool. According to the experimental data, we could achieve either the rust-formation rate or the porosity-formation rate, then, each rate was generalized as formulae. Then, we tried to combine these conflicting properties to decide an optimum shop primer.

• Journal of Welding and Joining
• /
• v.28 no.6
• /
• pp.21-27
• /
• 2010

Due to excellent weld quality, orbital welding with TIG is widely applied to pipe welding. But concave back bead is formed easily in overhead and inclined-up position of butt orbital welding. It is difficult to find a paper to overcome this problem. In this study, in order to make convex back bead in overhead and inclined-up position of pipe 5G welding, control method of molten pool was actively investigated. Melt run welds were conducted on thickness 4.0mm SS400 with overhead and inclined-up position and was observed the variation of bead shape after welding with the bead former developed. The height of back bead showed the trend of increase as the distance from molten pool to the bead former was decreased. Also, there is no trend in the bead width of front and back as welding position was changed or the distance from molten pool to the bead former was decreased.

• Journal of Welding and Joining
• /
• v.24 no.4
• /
• pp.22-26
• /
• 2006

In lap welding of zinc-coated steel, porosity formation is one of most significant weld defects, which is caused by zinc vapor generated between the steel sheets. Various solutions have been proposed in the past years but development of more effective method is a worthwhile subject to be investigated. In this study, autogenous laser welding and laser-TIG hybrid welding was applied to the lap welding of zinc-coated steel without gap, and weld pool behaviors were observed by using high speed camera and the porosity generation mechanism was analyzed. The weld defects were successfully eliminated by laser-TIG hybrid welding. This is because the leading TIG arc partially melted the upper sheet and vaporized/oxidized the coated zinc on the lapped surfaces prior to the trailing laser illuminating the specimen.

• Journal of Welding and Joining
• /
• v.15 no.1
• /
• pp.26-35
• /
• 1997

본 연구에서는 GTAW 및 GMAW 공정에서 용접부의 열 및 물질유동해석을 수행하기 위한 지배방정식, 해석방법 및 절차를 제시하였으며, 또 실제로 해석한 결과를 에제로 살펴보았다. 그러나 용접공정은 매우 복잡한 물리적 현상을 야기하기 때문에 용접부 수치해석 모델 설정 및 해석의 수행은 용이한 일은 아니다. 그렇지만 이 분야의 연구는 용접 구조물에 대해서 사전에 용접조건 설정을 위한 실제 용접 작업 수행을 하지 않고 용접부 형상, 결함, 냉각속도, 응고 등의 예측을 위한 매우 효과적이고 경제적인 방법으로 사료되기 때문에 용접 분야에 종사하는 관련 연구자들의 관심이 한층 더 요망된다.