• Proceedings of the KWS Conference
• /
• 2001.10a
• /
• pp.184-186
• /
• 2001

Quality estimation of the weld has been one of the important issues in RSW which is a main process of the sheet metal fabrication in auto-body industry. It was well known that among the various welding process variables, dynamic resistance has a close relation with nugget formation. In this study, a new quality estimation algorithm is developed with the primary dynamic resistance measured at welding machine timer. For this, Back propagation algorithm of neural network is used.

• Korean Journal of Metals and Materials
• /
• v.49 no.1
• /
• pp.64-72
• /
• 2011

The spot weldability of dissimilar metal joints between austenitic stainless steels (STS316)/IF steels and ferritic stainless steels (STS430)/IF steels was investigated. This study was aimed to determine the spot welding parameters for a dissimilar metal joint and to evaluate the dissimilar metal joint's weldability, including its welding nugget shape, tensile-shear strength, hardness, and microstructure. The comparison of these results was described in terms of fracture behavior. Compared with the weld lobe of similar metal joints, dissimilar metal joints (STS430/IF) had reduced weld current range. However, the weld lobe of STS316/IF steel joint showed increased weld current range. This is because the dilution of chemical composition in the molten weld pool suppressed the heat input being caused by Joule heat with current flow through the samples. The microstructure of the fusion zone was fully martensite and mixture of ferrite and martensite for austenitic stainless steel/IF steel and ferritic stainless steel/IF steel combination, respectively. The experimental results showed that the shape of nugget was asymmetric, in which the fusion zone of the austenitic and ferritic stainless steel sheet was larger due to the higher bulk-resistance. The predicted microstructure by using the Schaeffler diagram was well matched with experimental results. After peel test, the fracture was initiated from heat affected zone of ferritic stainless steel sheet side, however the final fracture was propagated into the IF steel sheet side due to its lower strength.

• Proceedings of the KWS Conference
• /
• 1998.10a
• /
• pp.129-132
• /
• 1998

The dynamic resistance monitoring in primary circuit or T/C is one of the important issues in that in-process and real time quality assurance of resistance spot weld is needed to increase the product reliability. It is well known that tile dynamic resistance curve gives us very useful information about nugget growth and weldability. In the present paper, a new dynamic resistance detecting method is presented as a practical manner of weld quality assurance using instantaneous current and voltage measured by primary circuit. Primary dynamic resistance patterns are basically similar to those of the secondary, but there is evident advantage such as no extra devices are needed to obtain the quality assurance index and eventually feedback control will be possible caused by T/C based monitoring system.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.6
• /
• pp.279-286
• /
• 1999

Failure of spot-weld joints in car body may cause noise, vibration and safety problems. Systematic procedures for estimating fatigue strength of general spot-weld joints are developed in this paper. Fatigue test results for various spot-welded specimens are analysed using the finite element method. It is found that the maximum principal strain at the nugget boundary on the inner surface governs the fatigue failure of spot-welded joints.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.330-335
• /
• 2002

Resistance spot welding is one of the most widely used processes in sheet metal fabrication. Quality assurance of welding has been important to increase the productivity. In this study, weld quality estimation using primary circuit dynamic resistance applied to the in-process real-time systems. For quality estimation, factors relating to quality were extracted from the dynamic resistance, measured in the timer. The relationship between these factors and weld quality was determined through a artificial neural network model. This method has the advantage over the conventional one, such as obtaining the quality information without the use of extra devices.

• Journal of Welding and Joining
• /
• v.10 no.1
• /
• pp.52-59
• /
• 1992

Resistance spot weldability of cold rolled 80kg/mm$^{2}$ and 45kg/mm$^{2}$ grade high strength steel sheets for automobile structure was investigated focussing on the influences of welding parameters such as welding current and welding time on the weld strength and the nugget formation. The results of this study showed that the optimum ranges of welding current for the grade 80 and grade 45 were 5.0 cycle(250 m sec.) It was also shown that the tensile shear strength of the resistance spot weld was strongly influenced by both current and time applied in welding procedure, however, the tensile shear strength was mainly affected by welding time for the higher strength steel.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.6
• /
• pp.1156-1169
• /
• 1989

본 연구에서는 용접도중 발생할 수 있는 용접질 저항요인을 전극분리현상을 측정하여 파악하고 용접 열입력에 해당하는 용접전류를 학습제어방식(self-learning control)에 의하여 컴퓨터와 주변기기(interface)를 통해 조절함으로서 요구되는 균일한 용접질이 항상 보장되도록 하였다. 여기서 학습제어방식을 태택한 이유는 제어하고자 하는 대상의 동적 모델(dynamic model)이 없어도 제어기 이득의 선정이 비교적 자유롭고 용접 제어장치가 자체적으로 감지(monitoring)한 신호로 판단하여 제어동작을 취함으로서 용접시 축적되는 정보(data)가 용접기에 일종의 지능을 부여할 수 있어서 진보된 개념의 용접제어장치 개발의 가능성을 검토해 보기 위함이다.

• Journal of Welding and Joining
• /
• v.28 no.6
• /
• pp.70-75
• /
• 2010

This study intends to investigate the weldability and mechanical characteristics of butt weld joints by LAFSW for dissimilar materials (Al6061-T6 and SS400). At optimum welding conditions, the tensile strength of dissimilar materials joints made by FSW is found to be lower than that of LAFSW. Due to the increase in plastic flow and formation of finer recrystallized grains at the TMAZ and SZ by laser preheating in LAFSW, the hardness in LAFSW appeared to be higher than that of FSW. Compared with FSW, finer grain size is observed and elongated grains in parent metal are deformed in the same direction around the nugget zone in TMAZ of Al6061-T6 by LAFSW. Whereas, at weld nugget zone, coarse grain size is appeared in LAFSW compared to FSW, which is owing to more plastic flow due to laser preheating effect. In dissimilar materials joints by LAFSW, ductile mode of fracture is found to occur at Al6061 side with fewer brittle particles. Mixed mode of cleavage area and ductile fracture is observed at SS400 side.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.99-99
• /
• 2010

최근 자동차 산업은 고효율 및 친환경이라는 전세계적인 이슈에 따라 고연비의 자동차 개발에 총력을 다하고 있다. 그러므로 다양한 고강도 강 및 경량 금속이 자동차의 차체에 적용되고 있다. 특히 철강재료에 있어서 기존의 저 탄소강에서 다양한 기능을 갖은 고강도 강으로 그 종류가 다양화되고 있으며 이에 따라 저항 점용접을 이용한 차체의 접합은 점점 이종의 강판을 접합하는 비율이 점차로 늘어나고 있다. 이와 같이 강판의 종류가 다양해짐에 따라 수많은 이종 강판에 대한 조합이 생기고 있으며, 이를 모두 실험을 통해 최적 용접조건을 찾기에는 많은 시간과 노력이 투자되어야 된다. 그러나 시뮬레이션 기법으로 이종 접합의 초기 용접조건에 대한 정보를 얻는다면, 최소의 실험을 통해 좀 더 손쉽게 최적의 용접조건을 도출할 수 있다. 그러므로 본 연구에서는 실제 자동차에 많이 쓰이는 강판인 EDDQ급 도금강판 0.7t와 440R 급 1.2t 및 DP 590 1.0t의 3종류의 이종 강판에 대한 점 용접특성을 저항 점용접 전문 소프트웨어인 SORPAS를 이용하여 시뮬레이션하고 분석하였다. 시뮬레이션은 겹치기 순서에 따라 용접 전류, 가압력, 용접 시간을 변수로 하여 각각의 겹침 순서에 대한 2개의 용접 점에 대한 너겟의 크기를 분석하였으며 로브 곡선을 얻을 수 있었다. 이를 통해 3겹의 겹치기 순서에 따른 용접 특성을 비교할 수 있었으며, 이것을 실제 생산라인의 자동차 차체의 조립 순서 결정에 있어서 응용함으로써 용접 특성을 고려한 차체 조립에 적용이 가능할 것으로 사료된다.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.11
• /
• pp.102-108
• /
• 2020

The demand for lightweight materials and high-strength steel has rapidly increased to help reduce the weight of a vehicle body; it improves the fuel efficiency of automobiles and provides passenger safety. Additionally, as the material becomes thinner, the demand for its resistance against corrosion becomes higher. Hence, the application of the surface-treated steel sheet has surged rapidly. In this study, a weld bonding experiment using a delta spot welding machine is performed on a thin sheet of a different material (Al6061-T6/GA440). The thickness of the material was kept at 1 mm to reduce the weight of the automobile body parts. Additionally, the purpose of this study is to control the heat input by applying the welding conditions of a multi-stage pressure pattern to improve corrosion resistance shear strength. The analysis of nugget diameter measurement, shear tensile test, and salt spray test was performed to achieve the aim.