• Journal of Welding and Joining
• /
• v.32 no.1
• /
• pp.79-86
• /
• 2014

The purpose of this study is to determine the proper fillet weld size for the stiffeners on hull bottom plate of crude oil tanker. To achieve it, the effective notch stress and hot spot stress of the fillet weld with leg length specified in the rule were evaluated by using comprehensive FE analyses. Based on the results, the fatigue damages at each location of weld were calculated. Meanwhile the transitional behavior of initial welding distortion in the hull bottom plate under the design conditions was investigated by using a non-linear FEA. Welding distortion and residual stress introduced during fabrication process were considered as initial imperfections. According to FE analysis results, if the fillet leg length satisfies the design criteria of the classification society, the concern on the root failure at the fillet welds in the bottom hull plate during the design life can be negligible. In addition, considering the transitional behavior of the distortion during the service life, the fillet leg length should be minimized.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.9
• /
• pp.1070-1077
• /
• 2011

This study intends to assess the defect in the weld zone of titanium grade 2 plate in terms of acoustical anisotropy based on the angle beam method. Depending on the rolling direction, the ratio of wave velocity was found to be 1.08 and the difference in the angle of refraction was more than seven degrees, confirming the presence of acoustical anisotropy. Thus for measuring the length of defect in the weld zone of the titanium plate (thickness of 10mm), the distance amplitude characteristics curves of titanium, TDACC-R and TDACC-T were constructed for the measurements in consideration of the acoustical anisotropy on CRT of the ultrasonic testing equipment. As a result, when the distance amplitude characteristics curve corresponds to the rolling direction, the length of defect was close to the actual measurement within 1mm and when different, the difference was found to be over 4mm. It was affirmed that the acoustical anisotropy should be taken into consideration when measuring the length of defects in the weld zone of the titanium plate with the presence of acoustical anisotropy.

• Journal of Welding and Joining
• /
• v.14 no.5
• /
• pp.113-121
• /
• 1996

The arc sensor has been most widely used for weld seam tracking through welding current or voltage variation. In this work, the relation between the arc light intensity and welding condition is investigated using heat balance in the Plasma for its possible application to seam tracking in the GMAW process. The arc light intensity is derived to be the function of the arc length and welding current Experiments are carried out to verify the proposed heat balance model. Performances of least square and integration methods to process the signals for seam tracking are compared experimentally. Predicted arc light intensity shows reasonably good agreement with experimental results. The weld seam is successfully tracked through the arc light intensity. The least square and integration methods demonstrate almost same performance of seam tracking with $CO_2$gas shielding.

• Proceedings of the KWS Conference
• /
• 1996.10a
• /
• pp.139-141
• /
• 1996

Among various welding parameters, the welding current which is inversely proportional to the tip-to-workpiece distance in GMAW is an essential parameter to monitor the GMAW process of horizontal fillet joints. For the case of weld defect such as overlap in horizontal fillet welding, therefore, the signal processing for process monitoring or automatic seam tracking should be modified by considering the weld pool surface geometry including the corresponding weld defect. In other words, the adequate signal processing algorithm is indispensible to improve the performance of the arc sensor. However, arc sensor algorithm already developed usually focus on weld seam tracing but do not considering the weld qualities. In this paper, various experiments were carried out to investigate the tendencies of the weld defects when weaving motion is added, and the experimental method based on 2$^n$ factorial design was proposed for deriving the mathematical model between the leg length and the various welding conditions. Moreover, a signal processing method based on the artificial neural network(Adaptive Resonance Theory) was proposed far discriminating the current signal of sound weld beads from that of weld beads with overlap. Finally, the algorithm for weld seam tracking combined with the mathematical modeling and the signal processing method was carried out to track the weld line in conjunction with the improvement of the weld qualities. The reliability of the proposed algorithms were evaluated through various experiments, which showed that the proposed algorithms could be effectively used for arc welding automation.

• Journal of Welding and Joining
• /
• v.25 no.5
• /
• pp.64-71
• /
• 2007

The aim of this paper is to investigate the effects of welding parameters on the weld shape in seal-welding of STS304L capsule for manufacturing a radioisotope source which is widely used in nondestructive testing of metal structures using gamma ray. Pulsed gas tungsten arc (Pulsed GTA) welding is performed for thin cross sectional area of the capsule. Seven welding parameters including current waveform parameters and arc length etc. are selected as main process parameters using design of experiment. The weld shape such as bead width, penetration depth, weld area, aspect ratio and area rate is investigated to assess the effects of welding parameters. As results, the combination of pulse duty/welding speed largely affects on bead width, penetration depth, area and aspect ratio. Finally, it is concluded that the key parameters are the combination of pulse duty/welding speed, base current and arc length, and their optimal conditions are 50%/1.77mm/s, 6.4A and 1 mm.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.1
• /
• pp.81-89
• /
• 2018

Austenitic stainless steels have excellent corrosion resistance, durability and fire resistance. Especially, since STS304L among austenitic types is a low-carbon variation of STS304 and has excellent intergranular corrosion resistance, it can often be used under the welded condition without heat treatment after field welding. This paper investigated ultimate behaviors such as ultimate strength and weld metal fracture mechanism of STS304L fillet-welded connections with TIG(tungsten inert gas) welding through test results. Main variables of specimens are weld length and welding direction against loading. Fracture of specimens are classified into three modes(tensile fracture, shear fracture and block shear fracture). Ultimate strengths were compared according to the welding direction and weld length and TFW series with transverse fillet weld had the highest strength compared with other types(LFW series with longitudinal fillet weld and FW series with all round weld). It is known that current design specifications such as KBC 2016 and AISC2010 underestimated the strength of TFW and LFW specimens and provided unconservative estimates for FW specimens. Finally, strength equations were proposed considering material properties of STS 304L material.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.10
• /
• pp.979-984
• /
• 2015

In the present paper, we evaluate the effects of the safe-end length and thickness of the similar metal weld (SMW) of safety injection nozzles on stress distributions at the dissimilar metal weld (DMW). For this evaluation, we carry out detailed 2-D axisymmetric finite element analyses by considering four different values of the safe-end length and four different values of the thickness of SMW. Based on the results obtained, we found that the SMW thickness affects the axial stresses at the center of the DMW for the shorter safe-end length; on the other hand, it does not affect the hoop stresses. In terms of the safe-end length, the values of the axial and hoop stresses at the inner surface of the DMW center increase as the safe-end length increases. In particular, for the cases considered in the present study, the stress distributions at the DMW center can be categorized according to certain values of safe-end length.

• International Journal of Korean Welding Society
• /
• v.1 no.1
• /
• pp.23-30
• /
• 2001

Among the various welding conditions, the welding current that is inversely proportional to the tip-to-work-piece distance is an essential parameter as to monitor the GMAW process and to implement the welding automation. Considering the weld pool surface geometry including weld defects, it should modify the signal processing method for automatic seam tracking in horizontal fillet welding. To meet the above necessities, a mathematical model related with the weld pool geometry was proposed as in a conjunction with the two-dimensional heat flow analysis of the horizontal fillet welding. The signal processing method based on the artificial neural network (Adaptive Resonance Theory) was proposed for discriminating the sound weld pool surface from that with the weld defects. The reliability of the numerical model and the signal processing method proposed were evaluated through the experiments of which showed that they are effective for predicting the weld bead shape with or without the weld defects in a horizontal fillet welding.

• Proceedings of the KWS Conference
• /
• v.43
• /
• pp.289-291
• /
• 2004

The purpose of this study is to identify the effects of the length of tack weldment on the rotational distortion at the one side SA butt weldment using experiment. The maximum rotational distortion at the end of the SA weldment decrease with an increase in the length of tack weld length, while the maximum rate of the distortion increases. This result indicates that the increase of the length of the tack weldment at the one-side SA butt weldment does not prevent the hot cracks.

• Journal of Welding and Joining
• /
• v.21 no.3
• /
• pp.46-50
• /
• 2003

The horizontal fillet joint is one of the most important weld joints in the shipbuilding industry. High-speed rotating arc welding, which can increase the leg length, is an effective way to improve the weld productivity and quality for the horizontal fillet welding. Based on the Taguchi method, the effects of welding parameters on bead characteristics - leg length, asymmetry, undercut, overlap - are investigated fur high-speed welding process. As a result, the adequate welding parameters are selected for the required leg length, symmetric bead and no undercut. Besides, considerably consistent leg length is observed for the horizontal fillet welding with gap variation up to 3mm.