• Anatomy and Cell Biology
• /
• v.51 no.4
• /
• pp.251-259
• /
• 2018

The aim of this study is to examine the correlation between tooth wear and age by quantitatively measuring maxillary first molar wear in children. A total of 150 maxillary dental models were analyzed in 30 subjects (male, 11; female, 19) with an age range of 6-14 years. Maxillary first molar wear were assessed based on area, volume and the shortest distance from the buccal occlusal plane to the central pit point (BCPH). The area and volume of the tooth cusps were measured at four different offset-plane heights (0.2, 0.4, 0.6, and 0.8 mm). Relationship between age and the amount of wear or BCPH were statistically analyzed. Correlation and regression analyses were also performed, and age estimation was obtained with linear regression analysis. Repeated measures analysis of variance (ANOVA) revealed significant differences between age and the amount of wear based on area, volume, and offset-plane height. Except age of 8 and 10, 12 and 14's 0.2-mm offset-plane-measured volume, all area and volume measurement of all ages and offset-plane height showed a significant amount of increase. Wear speeds were calculated using the BCPH. Among age and measurement variables, the correlation coefficient was strongest when the volume was measured from the 0.4-mm offset-plane. As age increases, the amount of wear, as quantified by area and volume measurements, also increases. According to this study, a regression equation that can be used for age estimation is follows: Age $(y)=0.16{\times}0.4V+0.85$ ($R^2=0.490$) using volume.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.50 no.2
• /
• pp.162-168
• /
• 2014

The friction and wear characteristics of the rubber matrix composites filled with nano sized silica particles were investigated at ambient temperature by pin-on-disc friction test. The volume fraction of silica particles was 19%. The cumulative wear volume and wear rate of these materials on counterpart roughness were determined experimentally. The major failure mechanisms were lapping layers, deformation of matrix, ploughing, debonding of particles, fracture of particles and microcracking by scanning electric microscopy photograph of the tested surface. The cumulative wear volume showed a tendency to increase with increase of sliding distance. The wear rate of these composites tested indicated low value as increasing the sliding distance.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.44 no.3
• /
• pp.250-256
• /
• 2008

Generally the side plate materials of FRP ship are composed of glass fiber and unsaturated polyester resin composites(GFRP composites). In this study, the effect of applied load and sliding speed on friction and wear characteristics of these materials were investigated at ambient temperature by pin-on-disc friction test. The cumulative wear volume, friction coefficient and wear rate of these materials for SiC abrasive paper were determined experimentally. The cumulative wear volume showed a tendency to increase nonlinearly with increase of sliding distance and was dependent on applied load and sliding speed for these composites. The friction coefficient of GFRP composites was increased as applied load increased at same sliding speed in wear test. It was verified by SEM photograph of worn surface that major failure mechanisms were microfracture, deformation of resin, cutting and cracking.

• Journal of Ocean Engineering and Technology
• /
• v.17 no.1
• /
• pp.55-60
• /
• 2003

The effect of size and volume fraction of ceramic particles, with sliding velocity on the wear properties were investigated for the metal matrix composites fabricated by the pressureless infiltration process. The metal matrix composites exhibited about 5.5 - 6 times the wear resistance compared with AC8A alloy at high sliding velocity, and by increasing the particle size and decreasing the volume fraction, the wear resistance was improved. The wear resistance of metal matrix composites and AC8A alloy exhibited different aspects. Wear loss of AC8A alloy increased with sliding velocity, linearly : whereas, metal matrix composites indicated more wear loss than AC8A alloy at the slow velocity region. However, a transition point of wear loss was found at the middle velocity region, which shows the minimum wear loss. Further, wear loss at the high velocity region exhibited nearly the same value as the slow velocity region. In terms of wear mechanism, the metal matrix composites generally exhibited abrasive wear at slow to high sliding velocity； however, AC8A alloy showed abrasive wear at low sliding velocity and adhesive and melt wear at high sliding velocity.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2002.10a
• /
• pp.379-384
• /
• 2002

The effect of size and volume fraction of ceramic particles with sliding velocity on the wear properties were investigated for the metal matrix composites fabricated by pressureless infiltration process. The particulate metal matrix composites exhibited about 5.5 - 6 times of excellent wear resistance compared with AC8A alloy at high sliding velocity, and as increasing the particle size and decreasing the volume fraction the wear resistance was improved. The wear resistance of metal matrix composites and AC8A alloy exhibited different aspects. Wear loss of AC8A alloy increased with sliding velocity linearly. whereas metal matrix composites indicated more wear loss than AC8A alloy at slow velocity region, however a transition point of wear loss was found at middle velocity region which show the minimum wear loss, and wear loss at high velocity region exhibited nearly same value with slow velocity region. In terms of wear mechanism, the metal matrix composites exhibited the abrasive wear at slow to high sliding velocity generally, however AC8A alloy showed abrasive wear at low sliding velocity and adhesive and melt wear at high sliding velocity.

• Tribology and Lubricants
• /
• v.17 no.1
• /
• pp.33-39
• /
• 2001

A method of calculating wear volume is developed using the signal processing technique. The lowpass filter with Fourier transform and the “windowing” are implemented in the method. User-defining feature is also included in determining the cutoff frequency of the low-pass filter and the baseline for the volume integration. Commercial software, MatLab, is used for the programming. Since the method uses the original wear data without simplifying the wear shape, it can give a further accurate result than the previously utilized methods, which often adopted the simplification. It becomes further powerful if the contacting body has a general shape rather than that gives well-formed surface traction (e.g., the Hertzian). The validation of applying the average surface roughness, Ra, to the “windowing” and the baseline for volume integration is discussed.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.256-261
• /
• 2004

To evaluate the effect of spring shape on the fretting wear of nuclear fuel rod, sliding wear tests were performed using three kinds of space grid springs in room temperature air and water. With increasing slip amplitude, wear volume of each spring gradually increased. It is apparently shown that spring with convex shape had a relatively high wear resistance compared with concave shape springs. It is suggested that the ratio of the wear volume to the worn area can be suggested as an efficient and valid parameter to evaluate the wear resistibility of a fuel grid spring.

• Tribology and Lubricants
• /
• v.13 no.1
• /
• pp.21-27
• /
• 1997

The friction and wear behavior of undulated surfaces made of tin base babbit are examined experimentally at the low sliding speed with severe loading condition. Steel is used as counterface disk material under pin-on-disk type sliding condition. Undulated surfaces can improve the friction and wear properties under dry friction condition since undulated surfaces trap wear particles in their cavities and prohibit wear particles from agglomerating. However, under boundary lubrication condition, friction and wear properties of undulated surfaces are inferior to those of flat surfaces. It is shown that land width and the ratio of wear volume to cavity volume are the most important factors in friction behavior of undulated surfaces under dry friction condition, and there exists optimum land width minimizing friction and wear of undulated surfaces.

• Tribology and Lubricants
• /
• v.19 no.2
• /
• pp.78-84
• /
• 2003

The SCM420 used mainly to automobile transmission gear has problems that it costs transmission gear maker much money in carburising treatment. For this, it needs to alternate the existing material and heat treatment to new gear material and surface modification. For this, friction and wear experiment according to sliding speed and applied load was carried out to evaluate the wear resistance of two transmission gear materials with carburising SCM420 and nitrocarburising NT100, The presumed wear volume was calculated with the image processing for evaluation of wear resistance of two transmission gear materials. The results show that nitrocarburising NT100 has a distinguished wear resistance than carburising SCM420.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.46 no.4
• /
• pp.495-502
• /
• 2010

The effect of load and sliding speed on abrasive wear characteristics of glass fiber/polyurethane (GF/PUR) composites were investigated at ambient temperature by pin-on-disc friction test. The friction coefficient, cumulative wear volume and surface roughness of these materials against SiC abrasive paper were determined experimentally. Experimental results showed that the surface roughness of the GF/PUR composites was increased as applied load was higher in wear test. The cumulative wear volume tended to increase nonlinearly with increase of sliding distance and depended on applied load and sliding speed for these composites. It could be verified by scanning electric microscopy (SEM) photograph of surface tested that major failure mechanisms were lapping layers, ploughing, delamination, deformation of resin and cracking.