• Journal of Technologic Dentistry
• /
• v.42 no.4
• /
• pp.348-354
• /
• 2020

Purpose: Zirconia is differentiated from other ceramics because of its high resistance to corrosion and wear, excellent flexural strength (900~1400 MPa), and high hardness. Dental zirconia with proven mechanical/biological stability is suitable for the manufacture of implants. However, there are limited in vivo studies evaluating stress distribution in zirconia compared with that in titanium implants and studies analyzing finite elements. This study was conducted to evaluate the stress distribution of the supporting bone surrounding zirconia and titanium implants using the finite element analysis method. Methods: For finite element analysis, a single implant-supported restoration was designed. Using a universal analysis program, eight occlusal points were set in the direction of the occlusal long axis. The occlusal load was simulated at 700 N. Results: The zirconia implant (47.7 MPa) von Mises stress decreased by 5.3% in the upper cortical bone compared with the titanium implant (50.2 MPa) von Mises stress. Similarly, the zirconia implant (20.8 MPa) von Mises stress decreased by almost 4% in the cancellous bone compared with the titanium implant (21.7 MPa) von Mises stress. The principal stress in the cortical and cancellous bone exhibited a similar propensity to von Mises stress. Conclusion: In the supporting bone, the zirconia implant is able to reduce bone resorption caused by mechanically transferred stress. It is believed that the zirconia implant can be a potential substitute for the titanium implant by reinforcing aesthetic characteristics and improving stress distribution.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.24 no.3
• /
• pp.371-377
• /
• 2020

Currently used iris cameras are expensive and have many limitations in their use. Existing iris cameras are inconvenient in interworking with newly developed software, and light reflections generated during iris photography are inadequate for medical use. Therefore, it is impossible to utilize the existing camera to take an image by yourself. In this paper, the iris camera is newly constructed so that the iris can be photographed by ourselves and the area of interest can be seen well. Anyone can easily wear glasses-type iris cameras to acquire images using IoT devices, and the acquired images are linked to the iris analysis program and used to read genetic weak parts. The proposed iris camera module automatically provides light reflection, shake, and accurate focus when capturing images, increasing the accuracy of image analysis to 91.49%. In addition, we have proved through experiments that one image processing time is fast as 0.007ms due to accurate image input.

• Human Ecology Research
• /
• v.59 no.1
• /
• pp.83-97
• /
• 2021

This study developed safety clothing that is essential for adolescent to protect their bodies from accidents, pursue activities and individuality. Therefore, the developed safety clothing was first based on international standards, while changing design to emphasize creativity, activity, and functionality. Two suits of boy's clothes and a girl's suit were developed as safety clothing for sportswear, along with two pairs of girl's clothes and a pair of boy's clothes for entertainment. It was confirmed that the difference in visibility was revealed by testing under different lighting conditions. Second, the survey on adolescents indicated no significant gender difference in sportswear. Round shirt+shorts for both boys and girls were the most preferred for ball game sportswear. However, there was a significant difference by gender in the design of safety clothing for entertainment. Male students preferred jump suit=cape+pants the most, and female students preferred jump suit>cape+pants in the order (p<0.05). In the safety clothes with the highest preference for entertainment, there was no gender difference. All students preferred the jump suit at the most. Checking at each school level, it was found that both middle and high school students preferred jump suit designs, and in safety clothing, middle school students preferred high-neck shirt blouse+tight skirt, and high school students preferred jump suits. Third, 35.5% responded that they would wear it more if current safety clothing is improved. This indicated the necessity of developing various safety clothing for adolescence.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.44 no.6
• /
• pp.1037-1052
• /
• 2020

This study evaluates the comfort and suitability of safety clothing. We made three safety clothes 'y', 'lg', 'lgH'. Only 'y' made with fluorescence fabric has passed International Standards (ISO 20471). A wearing test investigated the physiological response and subjective sensations at 30℃ and 50% RH, six men participated. Mean skin temperature and tympanic temperature showed significant difference with experimental course (p<.05). The micro-temperature (Tm) showed significant differences between three garments on the thigh (p<.01). When wearing 'lg', Tm was the highest. Micro-humidity indicated the interaction between clothing and the experimental course on the chest with no significant difference; however, there was a low tendency when wearing 'lgH' after the second half of exercise. The sweat rate indicated a significant difference between 'lg' and 'lgH' at 20 minutes of exercise (p<.05). Three sensations showed significant differences with the time (p<.01), there was also a tendency to feel hotter and more humid when wearing 'lg'. Skin sensation showed significant differences between pre-experiment and post-experiment (p<.05), 'y' was the most preferred. The 'lg' with long-sleeved currently worn in Korea tended to feel hotter, more humid and more uncomfortable than 'y'. It indicates that there is room for improvement in Korean safety clothing.

• Korean Journal of Metals and Materials
• /
• v.47 no.8
• /
• pp.508-515
• /
• 2009

Ti-6Al-4V biomaterial is widely used as a bone alternative. However, Ti-6Al-4V ELI alloy suffers from numerous problems such as a high elastic modulus and high toxicity. Therefore, non-toxic biomaterials with low elastic moduli need to be developed. Ti-HA(hydroxyapatite) composites were fabricated in the present work by pulsed current activated sintering (PCAS) at $1000^{\circ}C$ under 60 MPa using mixed Ti and HA powders. The effects of HA content on the physical and mechanical properties of the sintered Ti-HA composites have been investigated. X-ray diffraction(XRD) analysis of the Ti-HA composites, including Ti-40 wt%HA in particular, revealed new phases, $Ti_{2}O$, CaO, $CaTiO_3$, and TixPy, formed by chemical reactions between Ti and HA during sintering. The hardness of the Ti-HA composites decreased with an increase in HA content. The corrosion resistance of these composites was observed to be an excellent candidate as a commercial Ti-6Al-4 V ELI alloy. A Ti-5 wt%HA composite fabricated by PCAS is recommended as a new biomaterial, because it offers good corrosion resistance, compressive strength, wear resistance, and biocompatibility, and a low Young's modulus.

• Korean Journal of Metals and Materials
• /
• v.46 no.5
• /
• pp.321-327
• /
• 2008

Cu based amorphous ($Cu_{54}Zr_{22}Ti_{18}Ni_6$) coating was produced by cold spraying as a new fabrication process. The microstructure and macroscopic properties of amorphous coating layer was investigated and compared with those of cold sprayed pure Cu coating. Amorphous powders were prepared by gas atomization and Al 6061 was used as the substrate plate. X-ray diffraction results showed that Cu based amorphous powder could be successfully deposited by cold spraying without any crystallization. The Cu based amorphous coating layer ($300{\sim}400{\mu}m$ thickness) contained 4.87% porosity. The hardness of Cu based amorphous coating represented $412.8H_v$, which was correspond to 68% of the hardness of injection casted bulk amorphous material. The wear resistance of Cu based amorphous coating was found to be three times higher than that of pure Cu coating. The 3-point bending test results showed that the adhesion strength of Cu based amorphous coating layer was higher than that pure Cu coating. It was also observed that hard Cu base amorphous particle could easily deform soft substrate by particle collisions and thus generated strong adhesion between coating and substrate. However, the amorphous coating layer unexpectedly represented lower corrosion resistance than pure Cu coating, which might be resulted from the higher content of porosity in the cold sprayed amorphous coating.

• Korean Journal of Metals and Materials
• /
• v.46 no.9
• /
• pp.593-603
• /
• 2008

In this study, effects of alloying elements on the sticking occurring during hot rolling of five kinds of ferritic STS430J1L stainless steels were investigated by analyzing high-temperature hardness and oxidation behavior of the rolled steels. Hot-rolling simulation tests were conducted by a high-temperature wear tester which could simulate actual hot rolling. The simulation test results revealed that the sticking process proceeded with three stages, i.e., nucleation, growth, and saturation. Since the hardness continuously decreased as the test temperature increased, whereas the formation of Fe-Cr oxides in the rolled steel surface region increased, the sticking of five stainless steels was evaluated by considering both the high-temperature hardness and oxidation effects. The addition of Zr, Cu, or Si had a beneficial effect on the sticking resistance, while the Ni addition did not show any difference in the sticking. Particularly in the case of the Si addition, Si oxides formed first in the initial stage of high-temperature oxidation, worked as initiation sites for Fe-Cr oxides, accelerated the formation of Fe-Cr oxides, and thus raised the sticking resistance by about 10 times in comparison with the steel without Si content.

• Korean Journal of Metals and Materials
• /
• v.46 no.8
• /
• pp.477-481
• /
• 2008

The secondary hardening and fracture behavior in P/M high speed steels bearing V content of 9 to 10 wt% have been investigated in terms of austenitizing temperature and precipitation behavior. Austenitizing was conducted at 1,100 and $1,175^{\circ}C$ of relatively low and high temperatures. Coarse primary carbides retained after austenitization were mainly V-rich MC type. They give a significant influence on hardeness and toughness, as well as wear resistance. Tempering was performed in the range of $500{\sim}600^{\circ}C$. The peak hardness resulting from the precipitation of the fine MC secondary carbides was observed near 520, irrespective of austenitizing temperature. Aging acceleration(or deceleration) did not occur with increasing austenitizing temperature because it mainly influences contents of V and C of matrix through the dissloution of coarse primary MC containing lots of V and C. The precipitation of secondary MC carbides, which also contain V and C, did not change the aging kinetics itself. In the 10V alloy containing much higher C content, the impact toughness was lower than 9V alloy, because of the larger amount of primary carbide and high hardness.

• The Journal of Korean Academy of Prosthodontics
• /
• v.59 no.1
• /
• pp.134-145
• /
• 2021

In the case of excessively worn dentition, there is often insufficient space for the prosthesis, and if physiologically acceptable, the prosthesis can be fabricated by increasing the vertical dimension of occlusion. Various methods have been introduced to determine the vertical dimension of occlusion. Clinicians have to choose a method that can comfort the patient among several methods. A removable appliance can be used as a reversible method to ensure that the determined vertical dimension of occlusion does not cause physiological problems. When making impressions of many teeth, it is often difficult to make accurate impressions at once. In this case, after making an accurate impression of the individual teeth, a transfer coping was made and a pickup impression was taken in the oral cavity to create a master cast. In this case, a fixed partial denture was fabricated and full mouth rehabilitation was performed by increasing the vertical dimension of occlusion in a patient with excessively worn dentition and lack of space for restoration. As a result of follow-up of the patient for 7 years, satisfactory results were obtained both esthetically and functionally.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.23 no.1
• /
• pp.47-59
• /
• 2021

This study aims to provide inspiration and methods for menswear design by analyzing elements for men's fashion using flower images. The results are as follows: Men's fashion types with flower images were categorized as classic tailored, casual tailored, casual wear, sports-outdoor. The order of frquency was casual tailored, casual, classic tailored, and sports outdoor. For the classic tailored type, the flower images are related with an X-line silhouette, and the arrangement methods, such as a scattered patterns, one-point patterns, and surface techniques, such as printing and embroidery were used, and similar color or monochromatic schemes appeared sequentially. For the casual tailored type, the flower images are related to an H-line silhouette, arrangement methods such as a scattered pattern, panel pattern, and surface techniques, such as print, embroidery, and jacquard were used, similar color and accent color schemes appeared sequentially. For the casual type, the flower images are related to H-line and Y-line silhouettes, and arrangement methods, such as a scattered pattern, all-round continuous pattern, and panel pattern, and surface techniques, such as print, jacquard, embroidery, and patchwork were used, similar color and contrast color schemes appeared sequentially. For the sports outdoor type, the flower image were related to A-line and H-line silhouettes, arrangement methods, such as a scattered pattern and all-round continuous pattern, and surface techniques, such as print and jacquard were used, monochromatic scheme and contrast color schemes appeared sequentially. Therefore, the flower images in men's fashion were applied to various design elements, and displayed an interesting result, different from conventional design approach.