• Journal of Acupuncture Research
• /
• v.38 no.4
• /
• pp.300-311
• /
• 2021

Background: So far there is no confidence in the basics of acupoint/meridian phenomena, specifically in spatial and temporal electrical manifestations in the skin. Methods: Using the skin electrodynamic introscopy, the skin areas of 32 × 64 mm² were monitored for spectral electrical impedance landscape with spatial resolution of 1 mm, at 2 kHz and 1 MHz frequencies. The detailed baseline and 2D test-induced 2 kHz-impedance phase dynamics and the 4-parameter time plots of dozens of individual points in the St32-34 regions were examined in a healthy participant and a patient with mild gastritis. Non-thermal stimuli were used: (1) (for the sick subject), microwaves and ultraviolet radiation applied alternately from opposite directions of the meridian; and (2) (for the healthy one) microwaves to St17, and cathodic/anodic stimulation of the outermost St45, alternately. Results: In both cases, the following phenomena have been observed: emergence of in-phase and/or antiphase coherent structures, exceeding the acupoint conditional size of 1 cm; collective movement along the meridian; reversible with a reversed stimulus; counter-directional dynamics of both whole structures and adjacent points; local abnormalities in sensitivity and dynamics of the 1 MHz and 2 kHz parameters indicating existence of different waveguide paths. Conclusion: It is assumed that these findings necessitate reconsideration of some basic methodological issues regarding neurogenic/acupuncture points as spatial and temporal phenomena; this requires development of an appropriate approach for identifying the acuzones patterns. These findings may be used for developing new approaches to personalized/controlled therapy/treatment.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.259-259
• /
• 2010

Periodically polarity inverted (PPI) ZnO structures on (0001) Al2O3 substrates are demonstrated by plasmas assisted molecular beam epitaxy. The patterning and re-growth methods are used to realize the PPI ZnO by employing the polarity controlling method. For the in-situ polarity controlling of ZnO films, Cr-compound buffer layers are used.[1, 2] The region with the CrN intermediate layer and the region with the Cr2O3 and Al2O3 substrate were used to grow the Zn- and O-polar ZnO films, respectively. The growth behaviors with anisotropic properties of PPI ZnO heterostructures are investigated. The periodical polarity inversion is evaluated by contrast images of piezo-response microscopy. Structural and optical interface properties of PPI ZnO are investigated by the transmission electron microcopy (TEM) and micro photoluminescence ($\mu$-PL). The inversion domain boundaries (IDBs) between the Zn and the O-polar ZnO regions were clearly observed by TEM. Moreover, the investigation of spatially resolved local photoluminescence characteristics of PPI ZnO revealed stronger excitonic emission at the interfacial region with the IDBs compared to the Zn-polar or the O-polar ZnO region. The possible mechanisms will be discussed with the consideration of the atomic configuration, carrier life time, and geometrical effects. The successful realization of PPI structures with nanometer scale period indicates the possibility for the application to the photonic band-gap structures or waveguide fabrication. The details of application and results will be discussed.

• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.4
• /
• pp.19-22
• /
• 2017

In this study, wavelength-free $1{\times}N$ optical splitter using a tapered polymer waveguide was studied to realize the transmission network of high-speed information communication network. Based on the evaluation of mode converting characteristics of splitter having two tapered multi-mode interference structures, an optimized structure of the $1{\times}N$ splitter was proposed for wide-range of input wavelength. 2D-BPM analysis $1{\times}8$ model showed that insertion loss of the proposed splitter is less than 10 dB for wavelength of input source from 1260 nm to 1650 nm.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.4
• /
• pp.131-136
• /
• 2008

Two Ka-band 3-stage power amplifiers were designed and fabricated using $0.18-{\mu}m$ CMOS technology. For low loss matching networks for the amplifiers, two substrate-shielded transmission line structures, having good modeling accuracy up to 40 GHz were used. The measured insertion loss of substrate-shielded microstrip-line (MSL) was 0.5 dB/mm at 27 GHz. A 3-stage CMOS amplifier using substrate-shielded MSL achieved a 14.7-dB small-signal gain and a 14.5-dBm output power at 27 GHz in a compact chip area of 0.83$mm^2$. The measured insertion loss of substrate-shielded coplanar waveguide (CPW) was 1.0 dB/mm at 27 GHz. A 3-stage amplifier using substrate-shielded CPW achieved a 12-dB small-signal gai and a 12.5-dBm output power at 26.5 GHz. This results shows a potential of CMOS technology for low cost short-range wireless communication components and system.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.15 no.5
• /
• pp.108-115
• /
• 2016

In this paper, the array synthesis horn antenna was designed and measured a radiation power after connecting magnetron. The proposed antenna was designed on the basis of the $4{\times}4$ array synthesis horn antenna characteristics. For suppressing a back-lobe, 2 step short-stub structures were attached to synthesis horn aperture upper and lower. The designed antenna has FBR(Front to Back Ratio) of 39.7 dB. HPBW(Half Power Beam Width) of the E-plane and the H-plane are $8.86^{\circ}$ and $7.35^{\circ}$ each in the measurement. For measuring a radiation power of array antenna that use a magnetron, the waveguide adaptor was designed and connected magnetron with horn antenna. Also, microstrip line coupler that replace a dielectric material with an air gap was designed for measuring a high power. As a result, average radiation output power of the $4{\times}4$ array synthesis horn antenna that connect a four magnetrons had a 0.063W.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.3
• /
• pp.302-311
• /
• 2014

In this work, a FTTL (fishbone-type transmission line) structure was fabricated on PES (polyether sulfone) for a realization of transparent flexible wireless communication device, and its RF characteristics were investigated. According to the results, the FTTL on PES showed a short wavelength characteristic compared with conventional coplanar waveguide. Concretely, the wavelength of the FTTL was 2.23 mm at 50 GHz, which was 56.6 % of the conventional coplanar waveguide. According to the bandwidth extraction result, the passband of the FTTL on PES was 608 GHz. Unlike conventional periodic structures, the characteristic impedance of the FTTL on PES showed a very low frequency dependency, which means that the FTTL on PES can be used for application to transmission line and distributed passive components with a broadband operation frequency.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.30 no.4
• /
• pp.338-344
• /
• 2010

A double rotation C-scanning system and a software program Under-Sodium MultiVIEW have been developed for the under-sodium viewing of a reactor core and in-vessel structures of a sodium-cooled fast reactor KALIMER-600. Double rotation C-scanning system has been designed and manufactured by the reproduction of double rotation plug of a reactor head in KALIMER-600. Hardware system which consists of a double rotating scanner, ultrasonic waveguide sensors, a high power ultrasonic pulser-receiver, a scanner driving module and a multi channel A/D board have been constructed. The functions of scanner control, image mapping and signal processing of Under-Sodium MultiVIEW program have been implemented by using a LabVIEW graphical programming language. The performance of Under-Sodium MultiVIEW program was verified by a double rotation C-scanning test in water.

• Journal of the Korean Magnetics Society
• /
• v.15 no.2
• /
• pp.148-152
• /
• 2005

A novel interferometric isolator has been proposed and designed to fabrticate waveguide magnetooptic isolator operating at a wavelength of $1.55{\cal}um$. The device consists of MMI (multimode interference) couplers and has a magnetooptic guiding layer with different layer structure in arms of the inteferometer. The layer structures in the arms of inteferometer are $HfO_2/CeY_2Fe_5O_{12}/NOG$ and $SiO_2/CeY_2Fe_5O_{12}/NOG$, respectively. This configuration give rise to different nonreciprocal phase shift. In consequence, the isolator operates under a unidirectional magnetic field. The optimized structure of the isolator was determined by a 3D beam propagation method.

• Korean Journal of Optics and Photonics
• /
• v.16 no.3
• /
• pp.254-260
• /
• 2005

By incorporating large core polymer waveguides, which have been developed for increased alignment tolerance in passive fiber attachment, highly efficient variable optical attenuators are proposed. In order to find optimum device structures, 3-dimensional beam propagation method (BPM) simulations are performed. Heat distribution over the polymer film is calculated to find the 3-dimensional index profile data for the BPM simulation. Due to the small index contrast between the core and cladding materials in the large core waveguide, heat-induced radiation occurs for small heating power. While the ordinary VOA needs the temperature to change over $150^{\circ}C$ for 20 dB attenuation, the large core VOA requires only $70^{\circ}C$. In addition to the merit of passive fiber attachment, the proposed VOA has enhanced attenuation efficiency for the lower temperature change.

• The Journal of the Acoustical Society of Korea
• /
• v.40 no.1
• /
• pp.31-37
• /
• 2021

In this paper, we design an acoustic meta-material silencer that operates at low frequency to reduce noise in duct. A high refractive index meta-material silencer is demonstrated with a combination of zigzag structured thin waveguide and helmholtz resonator, which reduces the speed of sound. Finite Element Method (FEM) analysis via thermo-viscous acoustic mesh is performed in order to calculate thermo-viscous dissipation in sub-wavelength waveguide. Sound power reflection, transmission and absorption coefficients are obtained utilizing 4-Microphone Method. The results show that cut-off frequency and transmission loss can be controlled through adjusting intervals of the zigzag structures. A wide-band acoustic silencer is also suggested by connecting meta-materials in series or parallel.