• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.7
• /
• pp.557-564
• /
• 1998

A low loss x-cut $LiNbO_3$optical waveguide was fabricated by Yi in-diffusion, and the properties of guided-mode and the total insertion loss of the pigtailed waveguide with polarization maintaining fiber(PMF) were measured at optical wavelength 1550nm. for forming the waveguides, the parameters of diffusion, Ti thickness, waveguide line-width, length, diffusion temperature, time and atmosphere were set $1400{\AA}$, $8{\mu}m$, 3.3cm, $1050^{\circ}C$, 8 hours and wet bubbled oxygen, respectively. And then after the polishing and piatailing, it showed that the total insertion loss was -4.1dB for TM mode, -5.5dB for TE mode, and mode size, that is, the horizontal/ vertical size were $13.8{\mu}m/18{\mu}m$ for TM mode, $9.6{\mu}m/6.5{\mu}m$ for TE mode.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.5 s.96
• /
• pp.488-493
• /
• 2005

In this study, waveguide-to-CPW transitions were developed for integrating waveguide and MMIC at V-band. The finite element method for numerical analysis and repeated experiments were performed to propose two types of waveguide-to-CPW transition. Using quartz substrate, proposed structures were designed for low loss as well as broadband characteristics. These waveguide-to-CPW transitions showed a good reliability and insensitivity to matching precision, and they could be fabricated with lower cost than that of the conventional connectors. Proposed two types of the structure showed insertion loss less than 1.9 dB and return loss better than 14 dB from 53 GHz to 60 GHz except unwanted resonance region, respectively.

• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.12 no.3
• /
• pp.1-8
• /
• 2016

In this study, we evaluated the flow characteristics of various types of waveguide-below-cutoff (WBC) arrays and their shielding effectiveness (SE) of electromagnetic pulses (EMP) based on computational fluid dynamics (CFD). Three types of waveguides were selected for analysis: (1) grid type, (2) honeycomb type, and (3) multi-layer types (2-ply, 4-ply, 6-ply, and 8-ply). To analyze the air flow characteristics, the flow velocities in the longitudinal center of the WBC and the differential pressures between the WBC array inlet and outlet were evaluated. Consequently, we derive the following conclusions: (1) despite an increase in the inlet velocity, the pressure drop of the 6-ply multi-layer type did not significantly increase as compared to that of other types of waveguides (waveguide thickness of 0.1 mm, SE of 100 dB); (2) the grid and honeycomb type had the fastest flow rate of 17.5 m/s, which is approximately 2.5 m/s faster than that at the inlet (waveguide thickness of 1 mm, module size of 30 mm); and (3) the average pressure drop of the grid type waveguide is the lowest in the overall model, whereas that of the 8-ply is the highest (waveguide thickness of 1 mm, module size of 30 mm, and SE of 80, 100 dB).

• The Journal of the Acoustical Society of Korea
• /
• v.29 no.7
• /
• pp.448-457
• /
• 2010

Vibrations and wave propagations in waveguide structures can be analysed efficiently by using waveguide finite element (WFE) method. The WFE method only models the 2-dimensional cross-section of the waveguide with finite elements so that the size of the model and computing time are much less than those of the 3-dimensional FE models. For cylindrical shells or pipes which have simple cross-sections, the external coupling with fluids can be treated theoretically. For waveguides of complex cross-sectional geometries, however, numerical methods are required to deal with external fluids. In this numerical approach, the external fluid is modelled by the boundary elements (BEs) and connected to WFEs. In order to validate this WFE/BE method, a pipe submerged in water is considered in this study. The dispersion diagrams and point mobilities of the pipe simulated are compared to those that theoretically obtained. Also the acoustic powers radiated from the pipe are predicted and compared in both cases of air and water as an external medium.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.8
• /
• pp.1388-1393
• /
• 2010

This paper presents a new methodology for designing a dielectric waveguide filter with the cutoff frequency of 2.4 GHz based on the continuum design sensitivity analysis. An analytical sensitivity formula is derived in frequency domain and then unified program architecture applicable to the optimal design of high-frequency devices is proposed. A three-dimensional dielectric resonator used in waveguide filters has been tested to illustrate the validity of the proposed method.

• Journal of information and communication convergence engineering
• /
• v.10 no.2
• /
• pp.103-107
• /
• 2012

An end-launched adapter combining a coaxial loop within a rectangular waveguide has been analyzed and designed. The accurate electromagnetic modeling of input impedance for the adapter design has been developed using a modal analysis method. Also, design parameters to improve the end-launched adapter have been investigated. Numerical and experimental results of the proposed model have been compared with the results of previous works, and verified by an electromagnetic simulator of High Frequency Structure Simulator (HFSS). The input voltage standing wave ratios (VSWRs) are smaller than 2 over the wide frequency band from 7.5 GHz to 10.5 GHz.

• ETRI Journal
• /
• v.17 no.2
• /
• pp.1-10
• /
• 1995

We propose a novel planar optical interconnection scheme for 100 Gb/s optical packet address detection, which consists of waveguide grating couplers and a diffractive microlens integrated on a glass substrate 3-dimensionally. Length and duty cycle of the grating couplers have been determined on the bases of the ray-optic propagation-mode analysis in a slab waveguide and of the rigorous coupled-wave diffraction analysis for out-coupled radiation-modes. The 3-dimensionally integrated planar optics makes it possible to connect each address bit-signals of $TE_ 0-waveguide$ mode to the detector with a power uniformity of 6.4 % and a total coupling efficiency of 72.3 %.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.12
• /
• pp.65-73
• /
• 1995

In this paper, new algorithm which calculates transmission coefficient of electromagnetic wave by numerical analysis of scattered field by conductors with arbitrary cross-sections in parallel-plate waveguide is proposed. Proposed algorithm assumes magnetic current distribution on the boundary of scattering conductors, and applies Image theorem to perfect conductor surfaces of parallel-plate waveguide. Integral equations for fictitious magnetic currents on conducting boundary are set up. Magnetic current distributions on conducting boundary are expanded as exponential basis function, and using Galerkin method matrix equations are set wp. To compute matrix elements this method utilizes Fourier transform which is faster than numerical integration. Finally, frequency and incidence-angle characteristic of transmission coefficient are calculated and compared with experimental results.

• Journal of Sensor Science and Technology
• /
• v.27 no.1
• /
• pp.25-30
• /
• 2018

Closed-form analytical expressions and 3-dimensional normalized charts for the homogeneous sensing and surface sensing structures are derived to provide the conditions for the maximum sensitivity of integrated-optic biosensors based on evanescent-wave and stepindex planar optical waveguides. The analysis is made for transverse electric (TE) polarization mode, in both cases where the measurand is homogeneously distributed in the cover (namely, homogeneous sensing), and where it is an ultrathin film on the waveguide-cover interface (namely, surface sensing).

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.6
• /
• pp.11-19
• /
• 1997

For the circuit modeling of th ecoplanar waveguide (CPW) discontinuities, th eequivalent inductance is analyzed via the 3-dimensional boundary element method. The proposed method utilizes the magnetic scalar potential to obtain the magnetic flux passing sthrough the air-dielectric interfaces of the coplanar waveguide. The boundary integral is simplified by use fo the symmetry when the substrate is composed of the nonmagnetic material. In the numerical analysis, linear basis function and the collocationscheme are employed. The short-end and the step discontinuities are cahracterized through the calculations of the equivalent inductance andd the capacitance. The present method avoids the usual vector formulation and is quite advantageous in the quasi-staic characterization of the CPW disconditnuities.