• 한국전자파학회논문지
• /
• 제20권1호
• /
• pp.83-90
• /
• 2009

본 논문에서는 상호 평행하는 두 개의 도체 평판의 슬릿을 통한 전자파 투과 문제를 고려하였다. TM 편파된 평면파가 슬릿에 입사되었을 때 각 슬릿의 등가 자류를 미지수로 하는 결합 적분방정식을 유도하고 모멘트 방법으로 풀어 수치해석하였다. 슬릿의 폭, 도체 평행 평판의 간격, 평면파의 입사각, 슬릿간 변위 등에 따른 슬릿을 통해 투과된 전력의 변화를 계산하였다. 두 슬릿간 변위가 반 파장의 정수배에 근접할 때 투과 공진(최대 전력 투과)현상이 관찰되었다. 슬릿의 폭과 도체판 간격이 파장에 비해 매우 좁은 경우 투과 전력의 최대치는 슬릿의 폭과 입사각도에 무관하게 일정함을 확인하였다. 또한, 제안된 구조에서 일어나는 투과 공진 현상의 원리를 단순화된 구조와 등가회로를 통해 설명하였다.

• International Journal of Ocean System Engineering
• /
• 제3권4호
• /
• pp.188-208
• /
• 2013

The motion response of floating structures should be adequately low to permit the operation of rigid risers along with dry well heads. Though Spar platforms have low heave responses under lower sea state, could become unacceptable in near resonance region of wave periods. Hence the hydrodynamic response, heave in particular, must be examined to ensure that it is minimized. To reduce heave motions, external damping devices are introduced and one such effective damping device is heave plate. Addition of heave plate can provide additional viscous damping and additional added mass in the heave direction which influence the heave motion. The present study focuses on the influence of heave plate on the hydrodynamic responses of Classic Spar in regular waves. The experimental investigation has been carried out on a 1:100 scale model of Spar with single and double heave plates in regular waves. Numerical investigation has been carried out to derive the hydrodynamic responses using ANSYS AQWA. The experimental results were compared with those obtained from numerical simulation and found to be in good agreement. The influence of disk diameter ratio, wave steepness, pretension in the mooring line and relative spacing between the plates on the hydrodynamic responses of Spar are evaluated and presented.

• Composites Research
• /
• 제30권5호
• /
• pp.273-279
• /
• 2017

This paper describes the fabrication techniques and analysis of hybrid composite plates with an active frequency selective surface (FSS). For fabricating hybrid composite plate with active FSS, an active FSS with a resonance frequency located in the C band can obtained using varactor diodes. The hybrid composite plate was first designed and simulated to determine its electromagnetic properties using the commercial software HFSS. After simulation, active FSSs and hybrid composite plates were fabricated by mounting with varactor diodes. After fabrication, free space measurement was used to determine the electromagnetic properties of active FSS and the hybrid composite plates. The simulation and experimental results were in good agreement.

• Journal of Welding and Joining
• /
• 제13권1호
• /
• pp.145-155
• /
• 1995

Continuous wave C $O_{2}$ laser beam welding and formability of zinc coated steel plates were investigated. First, the optimal welding condition could be obtained in lap configuration by using the data for heat input, gap size and fracture behaviour. The gap size for fully-penetrated bead could be predicted by the gap model by Akhter et al. AIso, it was found that the joining efficiency was constant. Secondly, the butt welding of dissimilar materials (zinc coated steel plate and cold rolled steel plate) with different thicknesses was investigated. In the thickness range of 0.8-2.0 mm, the maximum welding speed of 10m/min was obtained. In the butt welding of two plates with thickness 2.0 mm and l.6mm, the maximum, welding speed of 6m/min was obtained, Finally. the forming results of butt-welded plates showed that the joining design was important to apply the laser welded blank in the automotive production.

• 대한기계학회논문집
• /
• 제15권6호
• /
• pp.2181-2188
• /
• 1991

본 연구에서는 주파수도메인에서의 측정방법중 진폭 스펙트럼 방법에 대한 이 론적 배경을 알아보고, 얇은 두께의 재료에 적용한 측정결과를 보이고자 하며, 비교적 두께가 두꺼운 재료에서의 측정결과를 위상 스펙트럼 방법으로의 측정 결과와 비교하 여 측정의 정확성을 서로 비교하였다.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2004년도 가을 학술발표회 논문집
• /
• pp.429-436
• /
• 2004

For the in-situ health monitoring of critical members in civil infra-structures, ultrasonic guided Lamb waves-based non-destructive evaluation (NDE) is very suitable. However, a chief drawback of the Lamb wave techniques is that multiple modes exist at all frequencies and the modes are generally dispersive, which means that the received signals may be very complicated. To overcome these complications, selective transmitting and receiving of a single A/sub 0/ mode within a frequency range can be adopted. Furthermore, a wavelet technique can be utilized to decompose the Lamb wave response into wavelet coefficients as a tool for signal processing. The changes in the Lamb waves interacting with damages in the steel plates are successfully characterized by this wavelet technique, through the amplitude change of the wavelet coefficients. In this paper, the feasibility of detecting a line crack on the surface of a steel plate and loosened bolts in a joint steel specimen using the Lamb waves and the wavelet technique is investigated.

• 비파괴검사학회지
• /
• 제33권3호
• /
• pp.276-282
• /
• 2013

This paper proposes an ultrasonic method for measurement of linear and hysteretic interfacial stiffness of contacting surfaces between two steel plates subjected to nominal compression pressure. Interfacial stiffness was evaluated by the reflection and transmission coefficients obtained from three consecutive reflection waves from solid-solid surface using the shear wave. A nonlinear hysteretic spring model was proposed and used to define the quantitative interfacial stiffness of interface with the reflection and transmission coefficients. Acoustic model for 1-D wave propagation across interfaces is developed to formulate the reflection and transmission waves and to determine the linear and nonlinear hysteretic interfacial stiffness. Two identical plates are put together to form a contacting surface and pressed by bolt-fastening to measure interfacial stiffness at different states of contact pressure. It is found from experiment that the linear and hysteretic interfacial stiffness are successfully determined by the reflection and transmission coefficient at the contact surfaces through ultrasonic pulse-echo measurement.

• 한국정밀공학회지
• /
• 제13권11호
• /
• pp.92-99
• /
• 1996

The contact pressure in jointed plates was measured by means of an improved ultrasonic technique. In order to get calibration curve, the relationship between contact pressure and ratio of boundary and bottom echo of normal beam probes were obtained for the calibration blocks with various surface roughness. The ratio of boundary and bottom echoes were measured for the upper/under plates locally compressed with uniform pressure, and the distribution of contact pressure was obtaines. The measured pressure has a good agreement with results of FEM analysis. Thus the proposed ultrasonic method in this work is very useful to measure the contact pressure.

• 한국전산유체공학회지
• /
• 제21권3호
• /
• pp.64-70
• /
• 2016

Multiple solutions in natural convection of water with Pr=7 between two horizontal plates with small magnitude non-uniform temperature distribution in the upper plate is numerically investigated. The dimensionless temperature of upper plate is ${\theta}={\epsilon}sinkx$. Two upright cells are formed over one wave length in the conduction-dominated regime of small Rayleigh number. However, multicellular convection occurs above a critical Rayleigh number for small wave number. When k = 1.5, dual solutions are found and a transition of $6{\rightarrow}4$ eddy flow occurs with decrease of Rayleigh number. When k = 0.75, two, three, four and five multiple solutions are observed. Transitions of $14{\rightarrow}12$, $12{\rightarrow}10$, $10{\rightarrow}8$ and $6{\rightarrow}8$ eddy flow occur with decrease of Rayleigh number.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.I
• /
• pp.345-348
• /
• 2005

In this paper we propose a configuration for an optically compensated bend (OCB) mode using circular polarizers with wide-band wide-viewing-angle (WBWA) quarter-wave plates (QWPs). Parameters of LC material and compensation films are optimized for wide viewing angle characteristics and excellent spectral properties of the OCB mode.