• Journal of the Society of Naval Architects of Korea
• /
• v.29 no.3
• /
• pp.131-139
• /
• 1992

By introducing a body potential, the high-oder spectal method of Dommermuth and Yue(1987) is extended to treat the nonlinear interactions between the free surface and the submerged cylinder. A 2-dimensional numerical wave tank is developed based on this numerical scheme, and applied to the wave resistance problem and the wave maker problem. In the simulations, it is shown that the transient waves due to the impulsive start of the body motion make a practical obstacle to the acquisition of useful data from the numerical experiments. Gradual starting procedures are devised, and successful result of the quasi-steady state or the uniform regular wave group was obtained. Within the author's present knowledge, the present numerical scheme is one of the most efficient numerical schemes which can treat the nonlinear interactions between the free surface and the body motion in time-domain.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.1
• /
• pp.205-210
• /
• 2006

The impact forces of the highly nonlinear waves are one of the important factors in designing the ocean structures. The impact forces are very difficult to analyze numerically and experimentally because they are impulsive in magnitude and occur instantaneously. In this study the numerical program based on N.S. equations are used to investigate the impact forces of steep waves where the waves are gene rated by the wave maker in the numerical wave basin. The arbitrary steep waves are generated by the superposition of waves of single frequency and the impact forces on vertical cylinder are simulated on the multiblock grids. V.O.F. and the local height function methods are used to track the free surfaces. To validate the numerical analysis the numerical results are compared with the experimental ones and the acceptable agreements are found. It is thought that more studies on the simulations of the incoming breaking waves and the impact forces on the vertical cylinder should be made to obtain the useful results to be applied in the offshore design.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2017.05a
• /
• pp.329-329
• /
• 2017

In this study attempted to evaluate the stability of the protection methods by examining hydraulic characteristics of the area around the point in which marine cable protector is installed such as surf zone occurrence point of shore-end submarine cables suitable for coastal marine environmental conditions, flow rate t the tope of the protector and maximum wave height, and to provide basic data for the selection of the optimal protection method. In performing hydraulic model experiments, the topography of submarine cable installation location was reproduced in 2-D sectional channel, and models appropriate for experimental scale and similitude law were produced and installed for each condition of submarine cables and protectors. Since the topography and submarine cable protectors were reproduced and installed in 2-D sectional channel, the exact reproduction of surf and transformation in shallow water zone was possible, and thus the physical properties could be clearly analyzed. For stability review, an experiment to examine the stability was conducted using a wave maker with 50-year frequency design waves as target, and wave height and cycles were applied based on the approximate lowest low water level(Approx. L.L.W), which is the most dangerous in submarine cable protection methods. As for experimental time, typhoon passing time in summer (about 3 hours) was applied, and wave patterns and deviation ratio of the submarine cable protector were investigated after making irregular waves corresponding to design waves. In addition, current meter and wave height meter were installed at the installation location of the submarine cable protector, and the flow rates and wave height at the top of the protector were measured and analyzed to review hydraulic properties.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.43 no.2
• /
• pp.101-115
• /
• 2007

The pound net fishery is very important one in Korean coastal fishery and it need to grasp the characteristics of the net affected by many factors. It is considered that the structure and the shape of the pound net can be changed by the direction and speed of current, wave height, depth and conditions of sea bed. However, most of all, the speed of current and wave height influence more upon the pound net than any other factors to deform and flutter. In this study, author carried out the experiments with a model of double one-side pound net made by the similarity law as 1:100 scales at a real experimental area, and additionally the model net experiments were conducted in the circulating water channel in Pukyong National University. The author analyzed the data of transformation of shape and tension of the model pound net to recognize the characteristics of the current and wave acting on it. Regardless of the direction of flow affecting on the fish court net or bag net, the deformed angle and depth to the side panel and bottom of box nets becomes bigger as the wave gets higher and the period of wave is faster. The tension in both upward or downward tends to be changed by the speed of wave. Those value of changes occurred similarly in either fish court net or bag net. Generally, when bag net is located at upward of flow, the value of tension was bigger 10% than any other location or nets. Regardless of the setting direction, the tension of the pound net is increased in proportion to flow speed, wave height and period of wave, and it becomes bigger about 15-30% at upward to flow than downward. Where the flow is upward in the court net, the tension in the wave increased to 37% compared to the one in the flow only in the condition of flow of 0.1-0.3m/s. Where the flow is upward in the bag net, the tension in the wave increased to 52% in the flow of 0.1m/s, and the tension increased to 48% in the flow of 0.2-0.3m/s.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.8
• /
• pp.621-627
• /
• 2014

In this paper, a possibility of controlling the motion of a floating wind turbine with the tuned liquid damper(TLD) is numerically investigated. First, motion of the scale model of a floating wind turbine without the TLD is predicted and its results are compared to the measured data. There are reasonably good agreements between two results, which confirms validity of the present numerical methods. Then, the effect of TLD is quantitatively assessed by comparing the prediction results for the floating wind turbine with and without the TLD. It is shown that the motion of the scale model derived by external forces can be reduced by using the TLD. On a basis of this result, a multi-layer TLD is proposed to generate larger reaction force of the TLD at the fixed target frequency. The motions of the scale model with the multi-layer TLDs are computed and compared with that of the single-layer TLD. It is shown that the multi-layer TLD generate stronger reaction force and thus more reduce the motion of the floating body than the single-layer TLD.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.10 no.4
• /
• pp.187-192
• /
• 2007

Impact on cylindrical surface caused by plunging breaking waves is investigated experimentally. The breaking waves are generated in a wave flume by decreasing the wave maker frequencies linearly and focusing the generated wave components at one specific location. The breaking wave packets are based on constant wave steepness spectrum. Three inclination angles of cylinder are applied to examine the effect of contact angle between cylinder and front surface of breaking waves. Also, the effect of cylinder diameter on pressure distribution and its peak value is investigated by adopting three cylinders with different diameters. The longitudinal location of cylinder is slightly moved in eight different points to find out a probable maximum value of impact pressure. The pressures and total force on cylinder surface are measured by piezo-electric pressure sensors and 3-components load cell with 30kHz sampling rate. The variation of peak impact pressures and forces is analyzed in terms of cylinder diameter, inclination angle and location. Also, the pressure distribution on cylindrical surface is examined. The cylinder location and surface position are more important parameters that govern the magnitude and shape of peak pressures, while the cylinder diameter and inclined angle are relatively insignificant. In a certain conditions, the impact phenomenon becomes very unstable which results in a large variation of measured valves in repeated runs.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2003.05a
• /
• pp.214-214
• /
• 2003

During a model test of Hutton TLP, a "ringing" response was first observed about 20 years ago. This phenomenon is a resonant build up over the time of wave period and this burst-like motion can cause the extreme load on the TLP tether. It is often detected in the large and steep irregular waves but the generation mechanism leading to the "ringing" is not yet well understood. According to the research since then, the higher order harmonic components may account for the "ringing" on the floating offshore structures. The main purpose of the present research is, thus, to measure the higher harmonic forces exerted on a vertical truncated circular column and to compare them with available data. A vertical truncated cylinder with a diameter of 3.5inch and a draft of 10.5inch is used as a test structure, which is a scaled model of ISSC TLP column. The cylinder is installed at a distance of 45ft from the wave maker in order to avoid parasitic waves created in the wave flap. Attached to the upper part of the cylinder are two force gages to measure the horizontal (surge) and vertical (heave) forces on the cylinder. The incoming waves are Stokes waves with a slope ranging from 0.06 to 0.24. The forces and waves are measured for 60 seconds with a sampling rate of 50 Hz. Among the recorded data, the first 10 waves are excluded because of transient behavior of the waves and the next The horizontal and vertical forces are analyzed up to 5th order harmonics. The horizontal forces are then compared to the values from the theoretical model called "FNV model". In addition, force transfer functions are also investigated. Major findings in this research are below. 1) The first order forces measured are slightly larger than the theoretical values of "FNV model" 2) The "FNV model" considerably overpredicts the second order forces. 3) The larger the amplitude and more extreme the wave slope, the smaller the predictions are compared to the experimental. 4) The higher harmonic forces are significantly smaller than the first harmonic force for all wave parameters. 5) The normalized forces vs. waves slopes are almost constant in the lower harmonics but vary a lot in the higher harmonics. 6) The trend of forces is more nonlinear in the horizontal forces than in the vertical forces as the wave slope increases. 7) The part of the results above is also observed by other researchers and confirmed again through the present work.

• The Journal of Industrial Distribution & Business
• /
• v.9 no.12
• /
• pp.23-29
• /
• 2018

Purpose - The purpose of this study is to apply a cost effective ultrasonic odor reduction method that generated micro-bubbles using ejector to the Southeast Asian wastewater market. Research design, data, and methodology - A leather maker located in Ansan-city, Gyunggi-do, South Korea was sampled from the collection tank to select experimental materials. Experimental setup consisted of circulating water tank-air ejector-ultrasonic device, and circulating wastewater. Sample analysis was performed by CODcr, T-N, T-P, and turbidity by the National Environmental Science Institute. Results - Experimental results show that it is most effective in removing odors when the frequency range of ultrasonic wave is 60~80 Khz and the output is 200 W. It showed that the concentration of complex odor dropped from a maximum of 14,422 times to a minimum of 120 times. Also, analysis of ammonia and hydrogen sulfide in specific odor substances has shown that they were reduced from 1.5 ppm to 0.4 ppm and from 0.6 ppm to 0.1 ppm, respectively. Conclusions - It is possible to shorten more than 12 hours in the treatment of micro-organisms. It can be seen that the processing time of odor after ultrasonic treatment in the pre-treatment facility is reduced by 25% when compared to the resultant micro-organisms after the chemical treatment, that is, the time of the bio-treatment of micro-organisms. Based on the results, it was confirmed that the pre-treatment method using the ultrasonic and the air ejector device of the experiment shows the effect of reducing the water pollutants and odor more effectively in a relatively short time than the conventional advanced oxidation method.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.43-43
• /
• 2011

최근 컴퓨터 기술의 발전으로 수심방향으로 완전한 운동방정식인 Navier-Stokes 방정식을 이용하는 3차원 수치모형에 의한 연구가 기초과학 분야인 수학에서부터 공학은 물론 의학 분야까지 광범위하게 진행되고 있다. 3차원 수치모형을 이용한 연구는 이론적으로 매우 우수하긴 하나 정확도 높은 결과를 얻기 위해서는 매우 조밀한 격자를 필요로 하기 때문에 아직까지 막대한 계산시간이 필요하다는 단점이 있으나 근래의 컴퓨터 기술이 엄청난 속도로 발전하고 있는 점을 감안할 때 적용 가능성은 계속 높아지고 있다. 이러한 흐름에 따라 해안공학 분야에서도 3차원 수치모형을 이용한 다양한 연구가 시도되고 있다. 복잡한 해안구조물로 인한 파랑변형 및 구조물의 안전성 등을 검토할 때 기존의 평면 2차원 수치모형이나 연직 2차원 수치모형으로는 재현이 힘들어 상대적으로 수치모형을 활용한 연구의 효용성이 낮았던 것에 비해 3차원 수치모형을 활용할 경우 복잡한 지형 및 구조물의 형상을 재현할 수 있기 때문에 좀 더 유용하게 사용될 수 있다. 한편, 파랑변형을 다루는 수치모형실험을 수행할 때 외부조파를 사용할 경우 구조물이나 지형에 의해 반사되어 나온 파랑이 조파지점에 도달할 때 실험영역으로 재 반사되는 문제가 발생한다. 이를 해결하기 위해 내부조파기법의 개발에 대한 연구가 필수적이었으며, 2차원 수치모형을 중심으로 그 연구가 매우 활발하게 진행되어 왔으나 Navier-Stokes 방정식 모형의 경우 상대적으로 연구가 미흡하였다. 본 연구에서는 3차원 Navier-Stokes 방정식 모형에서 내부조파기법을 도입하여 목표 파랑을 조파하였다. 수치모형은 Navier-Stokes 방정식을 엇갈림 격자체계에서 계산하는 유한차분모형으로 자유수면 추적에는 2차 정확도의 VOF(volume-of-fluid) 기법을 사용한다. 수치모형실험 결과를 일정한 수심을 전파하는 정현파의 해석해와 비교하였으며, 수치모형실험 결과가 비교적 정확하게 목표 파랑을 조파할 수 있음을 검증하였다.

• Korean Journal of Optics and Photonics
• /
• v.12 no.3
• /
• pp.230-234
• /
• 2001

We report a simple method for determining photovoltaic constant and conductivities of any photorefractive crytals which have no inversion symmetry by utilizing the electric field dependence of non-phase-matched second harmonic generation. New theoretical expression for the electric field dependence of Maker fringes is derived and space charge field can be determined using this from the observed change of intensity of second harmonic wave. The photovoltaic constant, dark conductivity and photoconductivity are easily deduced from an analysis of the measured relaxation behavior of space-charge field at two different light intensities. We demonstrate this method for $LiNbO_3$ at 514.5 nm.4.5 nm.