• Journal of Ocean Engineering and Technology
• /
• v.27 no.4
• /
• pp.68-75
• /
• 2013

This paper investigates the characteristics of waves generated by a flap-type wave maker in a two-dimensional wave channel. Measurements are carried out for various water depths, wave heights, periods, and lengths capacitance-type wave height gages. The experimental results are shown to satisfy the dispersion relation of the linear wave theory. For waves with a small height and long period, the wave profiles agree well with those of the linear wave theory. However, as the wave height and period become higher and shorter, respectively, it is shown that the wave profiles measured in the present experiments are different from the linear wave profiles, and the measured wave heights are smaller than the target wave heights, which may be due to the non-linearity of the waves. As the wave progresses toward the channel end, the wave height gradually decreases. This reduction in the wave height along the wave channel is explained by the wave energy dissipation due to the friction of the side walls of the channel. The performance of the wave absorber in the channel is found to be acceptable from the results of the wave reflection tests.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2003.10a
• /
• pp.303-308
• /
• 2003

In this paper, wave numerical modeling was experimented for the analysis of impact factors for the wave transmission as the incident wave and topographic conditions in the narrow channel sea. Recently, Although the results of many researcher for the wave modelling, numerical equations have limited to simulation of wave transformation effects. Despite of thispresent problems, the models was used to design the coastal structures in barrow channel sites. Finally, this paper estimated the wave model(mild slope eq. model) as the analysis of the wave energy transmission according to changing of impact factors(width of channel, bottom slope in channel, incident wave angle, wave period). As the results of numerical experiment, the major impact factors which influence to wave energy transmission were the width of channel and incident wave direction. But in the case that the width of channel is larger than 3L(L=Length of wave), the reduction of wave energy was small.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.13 no.1
• /
• pp.178-186
• /
• 2021

The wave power extraction by multiple Wave Energy Converters (WECs) deployed in a Y-shaped Water Channel Resonator (WCR) has been investigated. A WCR consists of a long water channel, and a V-shaped wave guider installed at the entrance of a water channel. If the period of the incident waves coincides with the natural periods of the fluid in a WCR, resonance occurs, as a result, the internal fluid in a WCR is greatly amplified. To estimate the wave power by multiple WECs placed at the antinodal points in a WCR, the heave motion response, time-averaged power, and capture width ratio were calculated for several design parameters. Also, the systematic model tests were conducted in a 2D wave tank. The numerical results are in good agreement with the experimental data. It was verified that a WCR helps the WECs to produce electricity more effectively by amplifying the wave energy in a WCR.

• Journal of Advanced Navigation Technology
• /
• v.13 no.6
• /
• pp.943-949
• /
• 2009

In this paper, the 5.9GHz WAVE(Wireless Access in Vehicular Environments) channel modeling is used by the Jakes channel model for the suitability of the fast wireless channel fluctuation. The performance analysed the fading signal constellation and the spectrum in the IEEE 802.11p spectrum mask, the Doppler effect, the modulation scheme. In addition, the vehicular speed, exactly the performance analysis the WAVE communication systems follow the Doppler effect.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.10
• /
• pp.2215-2222
• /
• 2010

A Wireless Access for Vehicular Environment (WAVE) system based on Orthogonal Frequency Division Multiplexing (OFDM) is made for vehicle to vehicle wireless communications. The physical layer standard of the WAVE system is very similar to that of the IEEE802.11a wireless local area network (WLAN). Therefore, the performance of the WAVE system is degraded by continual channel variation in the WAVE multipath fading channels after starting initial channel estimation. In this paper, we research the performance improvement of equalization in 64 Quadrature Amplitude Modulation (QAM) transmission in WAVE environment. The proposed algorithms use the training sequence and the midamble sequence which is used for fast channel variation such as WAVE environments. Additionally, various interpolation methods are also used for the channel tracking.

• Journal of information and communication convergence engineering
• /
• v.18 no.2
• /
• pp.88-93
• /
• 2020

The IEEE 802.11p-based wireless access in vehicular environments (WAVE) [1] communication is a method used exclusively for wireless communication on the road. This technique enables information sharing not only among moving vehicles but also between vehicles and infrastructure [2]. As part of WAVE communication, data is transmitted to and from vehicles in motion; in this case, it is difficult to determine the channel accurately in an outdoor environment owing to the Doppler shift [3]. This paper proposes a new channel estimation scheme for enhancing the reception performance of the IEEE 802.11p-based WAVE system. The proposed technique obtains the initial channel value by estimating the least square in the time domain by inserting a pilot signal for channel estimation into the IEEE 802.11p virtual subcarrier. Subsequently, a least mean square algorithm is applied to the initial channel value to update the estimated channel value. The simulation results obtained using the proposed channel estimation technique confirm its remarkable efficiency.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.367-370
• /
• 2007

Present study examines detonation wave propagation characteristics in annular channel. A normalized value of channel width to the annular radius was considered as a geometric parameter. A parametric study was carried out for a various regimes of detonation waves from weakly unstable to highly unstable detonation waves. Numerical approaches that used in the previous study of numerical requirements of the simulation of detonation wave propagations in 2D and 3D channel were used also for the present study with OpenMP parallization for multi-core SMP machines. The major effect of the curved geometry on the detonation wave propagation seems to be a flow compression effect, regardless of the detonation regimes. The flow compression behind the detonation wave by the curved geometry of the circular channel pushes the detonation wave front and results in the overdriven detonation waves with increased detonation speed beyond the Chapmann-Jouguet speed. This effect gets stronger as the normalized radius smaller, as expected. The effect seems to be negligible beyond the normalized radius of 10.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.531-535
• /
• 2008

Present study examines the detonation wave propagation characteristics in annular channel. A normalized value of channel width to the annular radius was considered as a geometric parameter. Numerical approaches used in the previous studies of detonation wave propagation were extended to the present study with OpenMP parallelization for multicore SMP machines. The major effect of the curved geometry on the detonation wave propagation seems to be a flow compression effect, regardless of the detonation regimes. The flow compression behind the detonation wave by the curved geometry of the circular channel pushes the detonation wave front and results in the overdriven detonation waves with increased detonation speed beyond the Chapmann-Jouguet speed. This effect gets stronger as the normalized radius smaller, as expected. The effect seems to be negligible beyond the normalized radius of 10.

• Journal of information and communication convergence engineering
• /
• v.8 no.3
• /
• pp.281-288
• /
• 2010

This paper investigates the performance of IEEE 802.11p wireless access in vehicular environments (WAVE) system in small-scale fading models reported by Georgia Institute of Technology (Georgia Tech). We redesign the small-scale fading models to be applied to the computer simulation and develop the IEEE 802.11p WAVE physical layer simulator to provide the bit error rate and packet error rate performances. Moreover, a new channel estimator using decision directed channel estimation and linear minimum mean square error smoothing is proposed in order to improve the performance of the conventional least square channel estimator using two identical long training symbols. The simulation results are satisfactorily coincident with the scenarios of Georgia Tech report, and the proposed channel estimator significantly outperforms the conventional channel estimator.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.594-599
• /
• 2009

Recent developments such as concern over global warming, depletion of fossil fuels and increase in energy demands by the increasing world population has eventually lead to mass production of electricity using renewable sources. Apart from wind and solar, ocean holds tremendous amount of untapped energy in forms such as geothermal vents, tides and waves. The current study looks at generating power using waves and the focus is on the primary energy conversion (first stage conversion) of incoming waves for different models. Observation of flow characteristics and the velocity in the augmentation channel as well as the front guide nozzle are presented in the paper. A numerical wave tank was used to simulate the waves and after obtaining the desired wave properties; the augmentation channel plus the front guide nozzle and rear chamber were integrated to the numerical wave tank. The waves in the numerical wave tank were generated by a piston type wave maker which was located at the wave tank inlet. The inlet which was modeled as a plate wall moved sinusoidally with the general function, x=asin$\omega$t The augmentation channel consisted of a front nozzle, rear nozzle and an internal fluid region representing the turbine housing. The analysis was performed using the commercial CFD code ANSYS-CFX.