• Journal of the Society of Naval Architects of Korea
• /
• v.35 no.3
• /
• pp.1-13
• /
• 1998

In the present paper, the hydrodynamic characteristics of three dimensional hydrofoils moving with a constant speed below the free surface using a higher-order boundary element method based on 9-node Lagrangian curvilinear elements are investigated. A bi-quadratic spline scheme is employed to improve the numerical results on the free surface. To validate the present scheme, the calculated results are compared with the analytic solutions for a submerged sphere and a spheroid showing a good agreement. For the validation of the hydrofoil study, the computed lift and drag of a hydrofoil having $NACA64_{1}A412$ section with aspect ratio(A.R.) of 4 are compared with the experimental data by Wadlin et al.[28]. The comparison covers a number of variations of angle of attack and submergence depth. Then, using an A.R. hydrofoil with NACA0012 section, the free surface on the lift and drag are investigated and these are compared with the previous results. The wave elevations and patterns created by the aforementioned submerged bodies are also investigated with Froude numbers and submergences.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.2
• /
• pp.208-215
• /
• 2017

When persistent oil, such as crude oil or Bunker C oil, is spilled at sea, viscosity increases through the weathering process. Equipment that can collect this oil when mixed with floating marine debris is very limited. In this study, devices that can be attached to the outside of existing oil skimmers have been applied to the inside of the main body, to develop an unmanned conveyor belt type floating marine debris and high viscosity oil recovery skimmer, which is composed of a conveyor belt, a sweeper with a forced inflow device, and a collection tank equipped with a buoyant body. The resulting skimmer was operated at a speed of 1.2 knots at a distance of 30 m in a sea area test. It was stable when moving laterally in any direction. An oil recovery performance test was conducted using a portable storage tank, and oil was recovered from a minimum of $7.8k{\ell}/h$ to a maximum of $23.3k{\ell}/h$. Moreover, recovery of $7.7k{\ell}/h$ was obtained in a wave water tank test with floating marine debris such as PET bottles and oil mixed. If the equipment developed in this study was used in the field for oil pollution accidents, it could be expected to contribute to improved response capability. We believe our equipment could be used in further studies to improvement the performance of existing portable oil skimmers.

• Geophysics and Geophysical Exploration
• /
• v.14 no.3
• /
• pp.227-233
• /
• 2011

Attention has been focused on geothermal energy as an alternative energy because it is continuously operable without external supply. Most of geothermal anomalies in Korea are related to deep circulation of groundwater through a fracture system in granite area. Therefore it is very important to understand the distribution of the fracture system which is the main channel of ground water. In this research, we constructed the velocity models with a fracture system and the layered sediments, respectively, and generated synthetic data sets with them to verify the presented vertical seismic profiling (VSP) preprocessing scheme. We compared the results from conventional VSP preprocessing flow to those from VSP preprocessing flow considering fracture system. We noticed that the preprocessing flow considering fracture system retains more sufficient signal including down-going wave than conventional preprocessing. In addition, we applied 3D VSP prestack phase screen migration to the preprocessed reversed VSP (RVSP) data from Seokmo Island so that we were able to image fracture structure of the geothermal site in Seokmo Island.

• Korean Journal of Plant Resources
• /
• v.23 no.1
• /
• pp.38-46
• /
• 2010

Phenolic compound contents and scavenging activity on DPPH and ABTS radicals in twelve fern species were studied by analysing ultrasonification extraction of dried aerial parts and rhizomes using methanol solvent. Total polyphenol content ranged from 2.97 to 140.1 mg per 1 g dried sample and 0.80 to $49.58\;mg{\cdot}g^{-1}$ fresh sample. Highest polyphenol content was obtained with aerial part of Davallia mariesii and Polystichum lepidocaulon. Total flavonoid content of dried sample was $2.56{\sim}34.91\;mg{\cdot}g^{-1}$ and fresh sample $0.71{\sim}11.49\;mg{\cdot}g^{-1}$. Higher flavonoids were obtained with dried aerial part of Dryopteris crassirhizoma, but with fresh aerial part of P. lepidocaulon. In general, total polyphenol content was higher in rhizomes, except in case of total flavonoid. Scavenging effects on DPPH and ABTS radicals was higher with rhizome extracts compared to aerial parts. The rhizome of Polystichum polyblepharum showed highest effects on both radicals. However, the amount of fresh sample for $RC_{50}$ with consideration of water content and extraction yield. P. lepidocaulon aerial part was more advantageous than P. polyblepharum rhizome. All the fern extracts except for the Coniogramme japonica extract demonstrated superior scavenging effects on ABTS radicals, being similar activity of ascorbic acid and BHT.

• Journal of Environmental Science International
• /
• v.29 no.3
• /
• pp.257-272
• /
• 2020

This study investigates the temporal and spatial variations of marine meterological elements (air temperature (Temp), Sea Surface Temperature (SST), and Significant Wave Height (SWH)) in seven coastal waters of South Korea, using hourly data observed at marine meteorological buoys (10 sites), Automatic Weather System on lighthouse (lighthouse AWS) (9 sites), and AWS (20 sites) during 2013-2017. We also compared the characteristics of Temp, SST, and air-sea temperature difference (Temp-SST) between sea fog and non-sea-fog events. In general, annual mean values of Temp and SST in most of the coastal waters were highest (especially in the southern part of Jeju Island) in 2016, due to heat waves, and lowest (especially in the middle of the West Sea) in 2013 or 2014. The SWH did not vary significantly by year. Wind patterns varied according to coastal waters, but their yearly variations for each coastal water were similar. The maximum monthly/seasonal mean values of Temp and SST occurred in summer (especially in August), and the minimum values in winter (January for Temp and February for SST). Monthly/seasonal mean SWH was highest in winter (especially in December) and lowest in summer (June), while the monthly/seasonal variations in wind speed over most of the coastal waters (except for the southern part of Jeju Island) were similar to those of SWH. In addition, sea fog during spring and summer was likely to be in the form of advection fog, possibly because of the high Temp and low SST (especially clear SST cooling in the eastern part of South Sea in summer), while autumn sea fog varied between different coastal waters (either advection fog or steam fog). The SST (and Temp-SST) during sea fog events in all coastal waters was lower (and more variable) than during non-sea-fog events, and was up to -5.7℃ for SST (up to 5.8℃ for Temp-SST).

• Journal of the Korean Institute of Intelligent Systems
• /
• v.25 no.2
• /
• pp.119-125
• /
• 2015

A concentration meter is widely used at purification plants, sewage treatment plants and waste water treatment plants to sort and transfer high concentration sludge and to control the amount of chemical dosage. When the strange substance is contained in the sludge, however, the attenuation of ultrasonic wave could be increased or not be transmitted to the receiver. At that case, the value of concentration meter is higher than the actual density value or vibrated up and down. It has also been difficult to automate the residuals treatment process according to the problems as sludge attachment or damage of a sensor. Multi-beam ultrasonic concentration meter has been developed to solve these problems, but the failure of the ultrasonic beam of a specific concentration measurement value degrade the performance of the entire system. This paper proposes the method to improve the accuracy of sludge concentration rate by choosing reliable sensor values and learning them by proposed algorithm. The prediction algorithm is chosen as neuro-fuzzy model, which is tested by the various experiments.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.6
• /
• pp.72-80
• /
• 2018

In this research, we tried to investigate the influence of concrete on cracks after applying to the actual construction site using the TPS construction method which can be easily charged by the mechanical injection method. To summarize the results, the following It is as follows. First, in the case of ultrasonic velocity, it can be seen that the ultrasonic wave passes rapidly at an average of about 36 mm / sec as compared with the syringe method when using the TPS method, and in the case of the injection depth, the syringe method In the case of TPS construction method, it showed an excellent tendency that 100% of the water retentive material was charged with all the formulations under a strong injection pressure. In the case of compressive strength, it was shown that the average was increased by 16.8% at the time of using the TPS construction method, and it was found to be structurally superior. Taken together, it is possible to confirm the behavior of the crack repairing agent by improving the quality by improving the strength and confirming the window installation by filling the injection material into the closed space at the crack site when using the TPS method compared with the syringe method. In addition, it is expected that construction time will be improved by shortening the construction period of about 5 days for the TPS construction method construction section 532 m, and usability will be expanded by the crack repair method of concrete structure.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.24 no.5
• /
• pp.305-318
• /
• 2012

Although the existing performance-based design method for the vertical breakwater evaluates an average sliding distance during an arbitrary time, it does not calculate the probability of the first occurrence of an event exceeding an allowable sliding distance(i.e. the first-passage probability). Designers need information about the probability that the structure is damaged for the first time for not only design but also maintenance and operation of the structure. Therefore, in this study, a time-dependent reliability design method based on a stochastic process is developed to evaluate the first-passage probability of caisson sliding. Caisson sliding can be formulated by the Poisson spike process because both occurrence time and intensity of severe waves causing caisson sliding are random processes. The occurrence rate of severe waves is expressed as a function of the distribution function of sliding distance and mean occurrence rate of severe waves. These values simulated by a performance-based design method are expressed as multivariate regression functions of design variables. As a result, because the distribution function of sliding distance and the mean occurrence rate of severe waves are expressed as functions of significant wave height, caisson width, and water depth, the first-passage probability of caisson sliding can be easily evaluated.

• Economic and Environmental Geology
• /
• v.41 no.4
• /
• pp.383-392
• /
• 2008

This study aims to evaluate the mechanical-chemical stability of used coal ash blocks, for improving fishing grounds. The surface of weathered ash blocks in seawater showed a decrease in the Ca and an increase in the Mg contents, compared to that of fresh blocks. This result reflects the substitution of Ca by Mg in seawater. The compressive strengths of ash blocks submerged into seawater during 12 months ranged from 235.23 to $447.43\;kgf/cm^2$; this is higher than the standard strength of wave-absorbing blocks($180\;kgf/cm^2)$ that are used for harbor construction. In addition, the compressive strength of ash blocks tends to increase with increasing installation time in seawater. The result of leaching experiments on coal ash blocks by Korean Standard Leaching Test(KSLT) method showed that leached concentrations of most metals except Cr(that leached up to 50 ppb, approaching standard concentration) do not exceed the seawater quality standards. A long-term(112 days) heavy metal leaching test to analyze seawater without mixing-dilution also showed that the concentrations of leached heavy metals, except for Cu, under anaerobic conditions do not exceed the seawater quality standards. Accordingly, the use of coal ash blocks in marine environments appears to be safe from chemical and mechanical factors that decrease the efficiency of concrete. Also, leaching concentration of Cu seems to be stable by decrease of leaching concentration due to dilution of seawater.

• Nuclear Engineering and Technology
• /
• v.27 no.4
• /
• pp.544-554
• /
• 1995

Pool boiling of dilute aqueous solutions of polyethylene oxide polymer has been experimentally investigated for the purpose of understanding the physical mechanisms of the suppression of vapor explosions in this polymer solution. Tn solid spheres of 22.2mm and 9.5mm-diameter ore heat-ed and quenched in the polymer solutions of various concentrations at 3$0^{\circ}C$. The results showed that minimum film boiling temperature($\Delta$ $T_{MFB}$) in this highly-subcooled liquid rapidly decreased from over $700^{\circ}C$ for pure water to about 15$0^{\circ}C$ as the polymer concentration was increased up to 300ppm for 22.2mm sphere, and it decreased to 35$0^{\circ}C$ for 9.5mm sphere. This large decrease of minimum film boiling temperature in this aqueous polymer solution may explain its ability to suppress spontaneous vapor explosions. Also, tests with applying a pressure wave showed that the vapor film behaved more stable against an external disturbance at higher polymer concentrations. These observations together with the experimental evidences of vapor explosion suppression in dilute polymer solutions suggest that the application of polymeric additives such as polyethylene oxide as low as 300ppm to reactor emergency coolant be considered to prevent or mitigate energetic fuel-coolant interactions during severe reactor accidents.s.