• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 제2회 학술대회 논문집 일렉트렛트 및 응용기술전문연구회
• /
• pp.25-28
• /
• 2000

In this paper, the technology for accelerating degradation & life estimation on the traction motor was introduced with the stator form-winding sample coils of the 200 Class insulation system The accelerative degradation was performed in 10 cycles, which were composed of thermal stress, fast rising surge voltage, vibration, water immersion and overvoltage applying. After aging of 10 cycles, condition diagnosis test such as insulation resistance & polarization index, capacitance & dielectric loss and partial discharge properties were investigated in the temperature range of $20{\sim}160^{\circ}C$. Relationship between degradation conditions and diagnosis results were analyzed to find an dominative degradation factor at the end-life point

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.964-968
• /
• 1996

The demands of size and quality of large steel shaft forgings for ship building, power plant, steel plant, etc. are rapidly increasing, and some of these productions are manufactured from ingot weighing more than 300 tons. For use as rotating components. shafts require toughness, strength and homogeneity, and therefore are produced through a variety of heat treatments. According to the increase of ingot size, micro- and macrosegregation and also mass effect of the product increase. Thus, special care should be paid to the heat treatment of such large shaft forgings. In this paper, the heat treatment of large shaft forgings such as rotor and back-up roll is calculated using the commercial finite element code SYSWELD. Calculated distributions of temperature and phase are compared with experimental data. The continuous cooling transformation diagram, thermal and mechanical properites of each phase are used. The phase proportion, hardness and residual stress during water quenching are discussed.

• 한국어병학회지
• /
• 제15권1호
• /
• pp.43-48
• /
• 2002

A blood biochemical analysis was carried out for the serum of wintering sea bream (red sea bream Pagrus major, black sea bream Acanthopagrus schlegeli, rock bream Oplegenathus fasciantuas) with green liver syndrome. GOT and GPT were significantaly elavated in the diseased sea bream. The value of $NH_{3}$ was slightly higher but those of TBIL. TP and UA were lower than the control. But there were no differences in albumin. Ca and glucose between the diseased and the control. These results suggent that a green liver syndrome in the sea bream might be related with nutritional defects and the stress of low water temperature during the winter.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 춘계학술발표대회 개요집
• /
• pp.185-187
• /
• 2005

The reactor pressure vessel head of PWR has penetrations for control rod drive mechanism and instrumentation systems. The Primary coolant water and operating temperature can cause the stress-corrosion cracking of these nickel-based alloy penetrations. It is difficult to detect and size flaws such as SCC in the reactor head penetrations using conventional W methods because of complex geometry, Therefore, the utilities are using the TOFD technique for the detection and sizing of the flaw. This study shows the correlation between the ultrasonic wave direction and the orientation of the flaw and the range of flaw depth which can be detected by the TOFD techniques.

• 한국실내디자인학회:학술대회논문집
• /
• 한국실내디자인학회 2004년도 추계학술발표대회 논문집
• /
• pp.84-87
• /
• 2004

The stress from the office environment comes from the most psychological things. Therefore, the purpose of this study is to research the psychological effect of natural element for office worker's psychological stability. This study is focused on the light, sound, air, temperature, plant, and water. Perception of these natural elements through the senses of sight, auditory, smell, and touch is effect on human body and mind directly. The application of natural elements provide a health of office workers. The result will show that, with application of the natural element, the rest space will be more powerful for health of workers. And also combination of natural element and geometric pattern will be very useful to prepare healing environment on the rest space

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.1120-1125
• /
• 2004

Welding characteristics of STS304 stainless steel and Inconel 600 using a continuous wave Nd:YAG laser are experimentally investigated. Alloy 600 being used in steam generator tubing of pressurized water reactor(PWR) exposed to some corrosion environment, stress corrosion cracking can occur on this material. Presented here are the results from a series of experiments in which dissimilar metal welds were made using the gas tungsten arc welding process with pure argon shielding gas. But It is well known that solidification cracking susceptibility of austenitic alloys depends on the solidification temperature range and amount/distribution of solute rich liquid that exists at the terminal stages of solidification. An experimental study was conducted to determine effects of welding parameters and to optimize those parameters that have the most influence on eliminating or reducing the extent welding zone formation at dissimilar metal welds.

• 한국전기전자재료학회논문지
• /
• 제15권1호
• /
• pp.93-101
• /
• 2002

In this study, the stator form-winding sample coils based on silicone resin and polyimide were made for fault prediction and reliability estimation on the C-Class(200$\^{C}$ ) insulation system of traction motors. The complex accelerative degradation was periodically performed during 10 cycles, which was composed of thermal stress, fast rising surge voltage, vibration, water immersion and overvoltage applying. After aging of 10 cycles, the condition diagnosis test such as insulation resistance '||'&'||' polarization index, capacitance '||'&'||' dielectric loss and partial discharge properties were investigated in the temperature range of 20 ∼ 160$\^{C}$. Relationship among condition diagnosis tests was analyzed to find a dominative degradation factor and an insulation state at end-life point.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.763-766
• /
• 2000

In this paper, stator form-winding sample coils based on silicone resin and polyimide were made for fault prediction and reliability estimation on the 200 Class insulation system of traction motors. The complex accelerative degradation was performed by periods during 10 cycles, which was composed of thermal stress, fast rising surge voltage, vibration, water immersion and overvoltage applying. After aging of 10 cycles, condition diagnosis test such as insulation resistance & polarization index, capacitance & dielectric loss and partial discharge properties were investigated in the temperature range of 20∼160$^{\circ}C$. Relationship among condition diagnosis test was analyzed to find an dominative degradation factor and an insulation state at end-life point.

• Nuclear Engineering and Technology
• /
• 제53권7호
• /
• pp.2295-2303
• /
• 2021

To investigate wall-thinning impact on axial load resistance of Zircaloy-4 cladding rods after a LOCA transient, axial tensile samples have been machined on as-received tubes with reduced thicknesses between 370 and 580 ㎛. After high temperature oxidation under steam at 1200 ℃ with measured ECR ranging from 10 to 18% and water quenching, machined samples were axially loaded until fracture. These tests were modeled using a fracture mechanics approach developed in a previous study. Fracture stresses are rather well predicted. However, the slightly lower fracture stress observed for wall-thinned samples is not anticipated by this modeling approach. The results from this study confirm that characterizing the axial load resistance using semi-integral tests including the creep and burst phases was the best option to obtain accurate axial strengths describing accurately the influence of wall-thinning at burst region.

• 한국토양비료학회지
• /
• 제28권2호
• /
• pp.165-175
• /
• 1995

토양수분정도가 보리의 수량 및 품질에 미치는 영향을 구명하여 보리의 가공이용에 적합한 양질의 원맥생산을 위한 토양수분기준설정의 기초자료로 활용코자 직경 52cm 높이 55cm인 대형 플라스틱 폿트에 사양토를 충진하여 강우차단시설을 갖춘 개폐형 하우스에 완전임의 3반복으로 배치한 뒤 올보리와 강보리 두 품종을 폿트당 40주의 밀도가 되도록 파종하였다. 토양수분장력이 각각 -0.05bar, -0.2bar, 0.5bar, -1.0bar, -5.0bar, -10.0bar에 도달되었을 때 토심 10cm주위가 충분히 젖어 장력이 0으로 될 때까지 관개를 하는 방법으로 토양수분을 조절하여 시험을 수행하였다. 토양수분장력은 micro tensiometer와 gypsum block을 토실 10cm에 설치하여 측정하였다. 분얼기로 부터 황숙기까지 토양수분을 조절 처리하여 재배한 보리의 생육특성 및 종실의 이화학적 특성을 조사한 곁과를 요약하면 다음과 같다. 1. 토양수분 스트레스가 장력 -1.0bar이하로 될 경우 간장과 절간장이 현저하게 짧아지고 간경이 작아지며 엽폭과 엽장이 크게 짧아지는 경향이였다. 2. 토양수분장력이 -0.5bar이하로 떨어지면 엽면적이 크게 감소하는 경향이나 주간의 지엽 및 제1엽중에 함유된 엽록소의 함량은 큰 차이가 없었다. 3. 뿌리활력은 토양수분스트레스가 증가할수록 대체로 떨어지는 경향이였으며, 품종별로는 올보리가 토양수분장력 -0.05bar구에서 뿌리활력이 가장 좋았으나, 조강보리는 장력 -0.05bar에서는 활력이 현저하게 떨어지는 반면, 장력 -0.2bar에서 가장 높은 활력을 보여 올보리보다 습해에 약한 것으로 나타났다. 4. 토양수분스트레스 증가에 따른 화분활력저하는 올보리에서는 뚜렷한 경향을 보이지 않았으나, 조강보리는 토양수분장력이 낮아질수록 현저한 감소를 보였으며, 주간의 불임율은 토양수분장력 -10.0bar이하에서 현저하게 증가하였다. 5. 이삭무게는 토양수분장력이 -1.0bar이상으로 될 때 올보리가 1.0~2.5g/ear, 조강보리가 0.5~1.7g/ear의 무게분포가 주를 이루고 있으나, 장력 -5.0/bar이하로 토양수분스트레스가 심한 처리구에서는 대부분 1.3g/ear이하의 가벼운 이삭이 주종을 이루웠다. 6. 곡립의 무게는 토양수분장력이 1.0bar이상으로 적습 범위일 때 올보리가 31~50mg/kernel, 조강보리가 21~45mg/kernel의 범위로 분포하고 있으나, 토양수분스트레스가 큰 장력 -5.0bar이하에서는 곡립무게가 현저히 떨어지는 경향이었다. 7. 곡립의 크기는 올보리와 조강보리 공히 2.2~2.6mm범위로 곡립분포를 보였으나, 토양수분스트레스가 심해질수록 이 범위이하의 작은 곡립이 증가하는 경향이었다. 8. 토양수분장력 -0.2bar를 관개시점으로 토양수분을 조절해 주었을 때 종실수량이 가장 많았고, 수분장력이 -1.0bar이하로 떨어지면 수량이 크게 감소하는 경향이었다. 9. 종실분의 조단백함량, 최고점도(Max. viscosity), 굳음성(Consistency) 및 ${\beta}$-glucan의 함량은 토양수분 장력이 낮아질수록 증가하는 경향이며, 특히 토양수분장력 -5.0bar이하일 때 현저한 증가를 보였고, 호화온도(Gelatiantion temp.)는 토양수분장력이 낮아질 수를 감소하는 경향이었다. 10. 수분이용효율은 올보리가 토양수분장력 -0.5bar, 조광보리가 토양수분장력 -1.0bar유지구에서 가장 높았고 이 범위보다 높거나 낮을 경우 효율이 떨어지는 경향이었다.