• The Journal of Engineering Geology
• /
• v.28 no.1
• /
• pp.61-67
• /
• 2018

Grouting is reinforcement or cutoff method which uses the hardening agent which is typically represented by portland cement and injected into the ground or the structure. When mixing the cement in powder form with water, the particles tend to cohere each other. Once they cohered, the particle size tends to become larger while injection efficiency becomes lower. This study, in a bid to reduce the cohesion of cement, the screen was set inside the grout mixer so that the cement particles are separated while vibrating them. To validate the effect of vibration screen, comparison test was conducted by using ordinary portland cement, slag cement and micro cement. Viscosity test, bleeding test and grain-size analysis indicated that the characteristics varied significantly after passing through the vibration filter. It is expected that the vibration filter installed inside the grout mixer will reduce the cement cohesion when mixing with water.

• Journal of the Korean Wood Science and Technology
• /
• v.1 no.2
• /
• pp.3-10
• /
• 1973

This study was carried out to examine the characeristics of waste sanders(S)from. plywood and pre-finishing plywood surface sanding and double saw finishing, as a new extander in urea-formaldehyde resin(UFR) in plywood adhesive, and to focus, adhesive strength using the glue extended with milled sanders(MS) as extender, leveling the optimum amount of MS to be added, and examining the physical properties of glue extended MS & S. Also economical good feasibility of substitution for wheat flour(WF) with MS as a new extender is analyzed and presented in details. Selecting three standard samples of 80, 100 and 180 mesh, sorking them in distilled water at $20^{\circ}C$, 24 hours, redrying at $105^{\circ}C$ and rescreening the sample with standard screen, again, the 3 samples of 80, 100, and 180 mesh are passed 23 percent through 80 mesh sander standard sample 27 percent through on 100 mesh and only 10.9 percent through 180 mesh, respectively. The particle size of retained parts are greater in size of redried form. It seems undoubtly that particles to be extended in glue are got swollen and become greater in size and coarser in shape. The shape of fresh S particles are irregular thin needle with small scale, as shown in Figure 5. PFS are so finer than plywood S that only 9.8 percent of the S retained on 100 mest screen, 24. 30 percent on 100-160 mesh, and 65.9% on 160-180 mesh. But particle size of the fresh S is large enough to make the viscosity of glue direct extended with S too high to apply it glue spreader. The glue extended with milled sanders(MS). 3 hours milled PFS or 6 hours milled plywood S, having particle sizes shown in Tables 7 and 8, as ratio of Reain/MS/WF/water: 100/8/8/10, indicate good viscosity of 16 to 24 ps, as shown in Figure 5, for applying direct to glue spreader, have high tensile-shear strength (adhesive strength), 102.4 kp/$cm^2$, and 94 percent wood failure.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.18 no.4
• /
• pp.320-327
• /
• 2006

Numerical analysis and experimental study are performed to investigate the effect of heat load and operating temperature on the thermal performance of several variable conductance heat pipe (VCHP) with screen meshed wick. The heat pipe is designed in 200 screen meshes, 500 mm length and 12.7 mm outer diameter tube of copper, water (4.8 g) is used as working fluid and nitrogen as non-condensible gas (NCG). Heat pipe used in this study has evaporator, condenser and adiabatic section, respectively. Analysis values and experimental data of wall temperature distribution along axial length are presented for heat transport capacity, condenser cooling water temperature change, degrees of an inclination angle and operating temperature. These analysis and experiment give the follow findings: For the same charging mass of working fluid, the operating temperature of heat pipe becomes to be high with the increasing of charging mass of NCG. When the heat flux at the evaporator section increases, the vapor pressure in the pipe rises and consequently compresses the NCG to the condenser end part and increases the active length of the condenser. From previous process, it is found out we can control the operating temperature effectively and also the analysis and experimental results are relatively coincided well.

• Radiation Oncology Journal
• /
• v.22 no.1
• /
• pp.64-68
• /
• 2004

Purpose : To study the feasibility of verifying real-time 2-D dose distribution measurement system with the scintillation screen for the quality assurance. Materials and Methods : The water phantom consisted of a scintillation screen (LANEX fast screen, Kodak, USA) that was axially located in the middle of an acrylic cylinder with a diameter of 25 cm. The charge-coupled device (CCD) camera was attached to the phantom In order to capture the visible light from the scintillation screen. To observe the dose distribution In real time, the intensity of the light from the scintillator was converted to a dosage. The isodose contours of the calculations from RTP and those of the measurements using the scintillation screen were compared for the arc therapy and the Intensity modulated radiation therapy (IMRT). Results : The kernel, expressed as a multiplication of two error functions, was obtained in order to correct the sensitivity of the CCD of the camera and the scintillation screen. When comparing the calculated isodose and measured isodose, a discrepancy of less than 8 mm in the high dose region was observed. Conclusion : Using the 2-D dosimetry system, the relationship between the light and the dosage could be found, and real-time verification of the dose distribution was feasible.

• Journal of Korea Water Resources Association
• /
• v.48 no.1
• /
• pp.23-35
• /
• 2015

In this study, the behavior of fresh water body between the injection and production wells with the fresh water injection rate in a saline aquifer is numerically analyzed by using a three-dimensional numerical model. 8 injection wells are arranged at equidistant intervals on a concentric circle and one production well is located at the center of this circle. In the case that the fresh water injection rate is relatively small, the fresh water body around a injection well screen is not mixed with neighboring ones and is independently distributed. However, when the injection rate is increased, the size of the fresh water body is continuously increased, and the areas, where saline and fresh water among injection wells are mixed, are appeared. The mixed degree is increased as the injection rate is increased. This phenomenon is identically generated around the production well. Moreover, when the injection rate is increased, the ratio of saline water in and around the production well is decreased.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.42 no.3
• /
• pp.208-214
• /
• 2022

Drought stress is a condition that occurs frequently in the field, it reduces of the agricultural yield of field crops. The aim of the study was to screen drought-adapted genotype of Italian rye grass. The experiments were conducted between the two Italian ryegrass (Lolium multiflorum L.) cultivars viz. Hwasan (H) and Kowinearly (KE). The plants were exposed to drought for 14 days. The results suggest that the morphological traits and biomass yield of KE significantly affected by drought stress-induced oxidative stress as the hydrogen peroxide (H₂O₂) level was induced, while these parameters were unchanged or less affected in H. Furthermore, the cultivar H showed better adaptation by maintaining several physiological parameter including photosystem-II (Fv/Fm), water use efficiency (WUE) and relative water content (RWC%) level in response to drought stress. These results indicate that the cultivar H shows improved drought tolerance by generic variation, improving photosynthetic efficiency and reducing oxidative stress damages under drought stress. These findings can be useful to the breeder and farmer for improving drought tolerance in Italian rye grass through breeding programs.

• Korean Journal Plant Pathology
• /
• v.14 no.6
• /
• pp.594-597
• /
• 1998

The optimal quantity of inoculum was determined to screen resistance of garlic cultivars against Sclerotium cepivorum and 30 cultivars was tested. The growth of the pathogen in detached roots, Disease incidence was increased when the inoculum density was raised form 10 to 100 sclerotia. The optimal inoculum density to differentiate resistance or susceptibility of garlic cultivars was seemed to be 50 sclerotia. The cultivars collected from England, Japan, Nepal and Turkey, and cultivars such as common red, PI1356104 and PI135693 were less than the other cultivars in their disease incidence. The growth of S. cepivorum in detached roots varied from 23 to 33 mm according to garlic cultivars. There was no relationship between the disease incidence and the growth in detached roots. The sclerotial germination was increased significantly when root extract was extract was added. The addition of only distilled water resulted in 13% germination, but the addition of 0.25 g of root extract in 100 ml distilled water resulted in more than 85% germination. There was no difference in the stimulation of sclerotial germination among cultivars which showed different resistance.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2005.10a
• /
• pp.164-169
• /
• 2005

It is design and manufacture which the rake operated in and out of water. Also irrigation test result of several times, the flux inside the waterway collects 0.15m/s to case below the dirt which is accumulated in the rake 30kg, difficulty was to examine closely the thing, it followed hereupon and the grade in the agriculture waterway flux inside the cursor waterway was quick, or, with water level in dirt removal it established in the irrigation facility downstream it will be able to increase a flux, very the possibility of getting an efficient power it is it knew.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.4
• /
• pp.570-575
• /
• 2010

This study is regarding development of an index table for antomation of welding process in impeller fabrication. A PLC, which is widely used for automation in industry, was also adopted as a controller for the index table because of it effectiveness, easy maintenance and repair. The index table consists of centering jig, blade jig, workbench, driving system and a controller. A touch screen was also prepaired as a man-machine interface to provide convenience for workers. Water jacket was installed inside the workbench to reduce thermal stress come from the welding. Temperature of the water jacket was kept constant to cool an impeller main plate effectively. The index table developed in this study convinces that it reduces the total welding time by 50% compared with the conventional process without the table.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1599-1600
• /
• 2007

The DTL water skid cooling system and Resonant Control Cooling Systems (RCCS) will employ a control system that can be operated by a local, programmable logic controller (PLC), interfaced through a touch screen interface, mobile alarm SMS server system, or it can be operated through the PEFP global control system network. The RCCS is implemented using Experimental Physics and Control System (EPICS) based hardware and software and is integrated with other networked PEFP EPICS systems. This presentation discusses the features of the local control system.