• Bulletin of the Korean Chemical Society
• /
• v.31 no.7
• /
• pp.1976-1980
• /
• 2010

A simple and reliable method has been developed to selectively separate and concentrate trace amounts of Fe(III) ions from water and food samples by using flame atomic absorption spectrometry. A new reagent, 5-hydroxy-4-ethyl-5,6-di-pyridin-2-yl-4,5-dihydro-2H-[1,2,4] triazine-3-thione, was synthesized and characterized by using FT-IR spectroscopy and elemental analysis. Effects of pH, concentration and volume of elution solution, sample flow rate, sample volume and interfering ions on the recovery of Fe(III) were investigated. The optimum pH was found to be 5. Eluent for quantitative elution was 10 mL of 2 M HCl. The preconcentration factor of the method, detection limit (3s/b, ${\mu}gL^{-1}$) and relative standard deviation values were found to be 25, 4.59 and 1%, respectively. In order to verify the accuracy of the method, two certified reference materials (TMDA 54.4 lake water and SRM 1568a rice flour) were analyzed. The results obtained were in good agreement with the certified values. The method was successfully applied to the determination of Fe(III) ions in water and food samples.

• Korean Chemical Engineering Research
• /
• v.54 no.5
• /
• pp.636-647
• /
• 2016

Magnetite nanoparticles ($Fe_3O_4$ NPs) were synthesized by co-precipitating method under optimized condition. The $Fe_3O_4$ NPs coated with sodium dodecyl sulfate-thenoyltrifluoroacetone ($Fe_3O_4$ NPs-SDS-TTFA) were then exerted as the magnetic solid phase extraction (MSPE) adsorbent for the extraction process prior to introducing to a flame atomic adsorption spectrometry (FAAS). The synthesized $Fe_3O_4$ NPs-SDS-TTFA were applied for the extraction of Pb(II) ions from different water samples. The characterization studies of nanoparticles were performed via scanning electron microscopy-energy dispersive micro-analysis (SEM-EDAX), X-ray diffraction (XRD) and vibrating sample magnetometer (VSM) techniques. The substantial parameters affecting the extraction efficiency were surveyed and optimized. A dynamic linear range (DLR) of $10-400{\mu}g\;L^{-1}$ was obtained and the limit of detection (LOD, n=7) and relative standard deviation (RSD%, n= 6, $C=20{\mu}g\;L^{-1}$) were found to be $2.3{\mu}g\;L^{-1}$ and 1.9%, respectively. According to the results, the proposed method successfully applied for the extraction of Pb(II) ions from different environmental water samples and satisfactory results achieved.

• Journal of Environmental Science International
• /
• v.6 no.5
• /
• pp.513-520
• /
• 1997

This study was performed to investigate the riverbed structure and the pollution type in Nakdong River, Western Nakdong River. and Suyoung Stream. Sediment and water samples were collected at is in Nakdong River. in Western Nakdong River, and 8 states In Suyoung Stream from February 20, 1997 to June 15, 1997. The depth distributions of sampling sites in the three streams were measured and heavy metals(Cd, Pb, Cr, Cu) and pesticides in sediments and COD, BOD, and total nitrogen(T-N) in water samples were analysed. The deepest and the shallowest sites were strate 11(11.58m) and 9(3.35m) in Nakdong River, site 7(6.25m) and 4(2.06m) in Western Nakdong River, and site 8(2.89m) and 1(0. 61m) in Suyoung Stream , respectively. The mean concentration of Cd(45.79ppm) was higher In the sediment of Western Nakdong River than In other two streams and those of Pb(76.25ppm), Cr(48.13ppm), and Cu(77.50ppm) were higher in file sediment of Suyoung Stream than in other two streams. Pesticides(1 kind of organophosphorus and 3 kinds of organochlorine pesticide) were detected only in the sediment of Western Nakdong River. The mean concentrations of COD(20.26ppm), BOD(25.36ppm), and T-N(18.05ppm) were higher in the water sample of Suyoung Stream than In other two streams.

• Journal of Korean Society of Water and Wastewater
• /
• v.21 no.2
• /
• pp.151-164
• /
• 2007

Criteria for rehabilitation priority are discussed to evaluate structural stability of deteriorated water transport and transmission pipes, in this study. For the purposes, safety factor is introduced and estimated by measuring tensile strength and by analyzing stress caused by the internal-external loads working on buried pipe body. Related informations are surveyed and collected under various conditions in the fields by digging out and the structural stability is assessed. In the evaluation results of structural safety, it is shown that steel pipe is more affected by external load than internal load. The average external load is estimated as $53.7kg/cm^2$ and total hoop stress is estimated by $2676.5kg/cm^2$. Also, Poisson effect into longitudinal direction due to internal and external loads is most influential on hoop stress. The calculated safety factors of hoop stress are ranged from 0.7 to 5.2 with average value of 2.1, considering a bending stress to longitudinal direction. The decision of rehabilitation priority by safety factors show that structural safety of CIP sample 1(S1) was assessed at the lowest order with safety factor value, 0.7 and that of DI sample 15(S15) was evaluated as the most stable in structural aspect.

• Journal of Microbiology and Biotechnology
• /
• v.9 no.6
• /
• pp.784-788
• /
• 1999

The effects of pH, moisture content, and the relative amount of a polymer sample on the biodegradation of degradable polymers in soil were studied using various polymer materials such as cellulose, poly-(butylene succinate-co-adipate) (SG) polycaprolactone (PCL), a blend of PCL and starch (PCL-starch), and a poly-lactic acid (PLA). As with other materials, the polymers degraded faster at a neutral pH than at either acidic or basic conditions. Moisture contents of 60 and 100% water holding capacity exhibited a similar biodegradability for various polymers, although the effects differed depending on the polymer. For synthetic polymers, biodegradation was faster at 60%, while the natural polymer (cellulose) degraded faster at 100%. Fungal hypae was observed at a 60% water holding capacity which may have affected the biodegradation of the polymers. A polymer amount of 0.25% to soil revealed the highest biodegradability among the ratios of 0.25, 0.5, and 1%. With a higher sample amount, the residual polymer could be recovered after the biodegradation test. It was confirmed that a test for general biodegradation condition can be applied to plastic biodegradation in soil.

• Journal of Korean Ophthalmic Optics Society
• /
• v.11 no.2
• /
• pp.143-149
• /
• 2006

The purpose of this study is synthesizing silicone polymer which is used the material of contact lens and solving the problems of water content and light transmittance for gas permeable contact lens. We used NVP, MMA, HEMA monomer for polymerization and EGDMA as cross linking regent. Also, we polymerized with a several formulation arrangement for the best condition as contact lens. After that. we measured water content and light transmittance by each sample which was polymerized. We polymerized the silicone polymer which is simultaneously pursued by the transparent and water content of the material and measured their physical nature of each sample on this study.

• Environmental Analysis Health and Toxicology
• /
• v.18 no.3
• /
• pp.199-208
• /
• 2003

A new technique was proposed for the determination of alkylphenols, chlorophenols and bisphenol A in tap water samples. The sample preparation consists of a solid phase extraction (SPE) of alkylphenols, chlorophenols and bisphenol A from a water sample with XAD-4 and subsequent conversion to isobutyloxycarbonyl (isoBOC) derivatives or tert-butyldimethylsilyl (TBDMS) derivatives for sensitive analysis with the CC/MS SIM mode. The recoveries were 86.6 ∼ 105.2％ (isoBOC derivatization) and 97.6∼484.5％ (TBDMS derivatization), respectively. The limit of quantitation of alkylphenols, chlorophenols and bisphenol h for SIM were 0.001∼0.050 $\mu\textrm{g}$/1 (isoBOC derivatization) and 0.003∼0.050 $\mu\textrm{g}$/1 (TBDMS derivatization). The SIM responses were linear with the correlation coefficient varying 0.9755∼0.9981 (isoBOC derivatization), and 0.9908∼0.9996 (TBDMS derivatization). When these methods were applied to tap water samples, the range of concentrations were 22.8∼31.3 ng/1 in 2,4-dichlorophenol, 28.6∼70.3 ng/1 in pentachlorophenol, 15.2∼17.4 ng/1 in t-butylphenol, 10.8∼13.2 ng/1 in t-octylphenol and 17.6∼36.3 ng/l in bisphenol A, respectively.

• Journal of the Korean Applied Science and Technology
• /
• v.37 no.6
• /
• pp.1619-1626
• /
• 2020

In this study, the physical properties of water-dispersible polyurethane resins synthesized with polyammonium phosphate and HMDI were studied by coating film samples and full-grain surfaces. Solvent resistance was found to be unchanged in all samples, and in terms of tensile strength, DPU-AP3 (1.887 kgf/㎟) containing the most ammonium polyphosphate showed the lowest physical properties. The elongation rate was measured as 54 8% in the sample containing a large amount of ammonium polyphosphate. Abrasion resistance was measured as 548 mg.loss of a sample containing a lot of ammonium polyphosphate, and it was confirmed that the physical properties of the blended resin of ammonium polyphosphate and water-dispersible polyurethane were changed.

• Korean Journal of Metals and Materials
• /
• v.47 no.12
• /
• pp.873-880
• /
• 2009

Water-vapor permeation through metallic barriers deposited on polymer substrates has been an important technological issue because the performance of the barrier is critical to the reliability of flexible organic devices. For the development of long-lifetime flexible organic devices, two different sets of samples were designed and demonstrated from the viewpoint of the water-vapor transmission rate (WVTR). Aluminum (Al) and polyethylene terephthalate (PET) were chosen for the barrier layer and the polymer substrate, respectively. Two stacking structures, a single-layer (Al/PET) structure and a double-layer (Al/PET/Al) structure, were used for the WVTR measurement. For the single-layer structure, the WVTR decreases as the thickness of the barrier layer increases. Compared to the single-layer sample, the double-layer sample showed superior WVTR performance (by nearly three times) when the total thickness of the Al barrier was greater than 100 nm.

• Analytical Science and Technology
• /
• v.20 no.1
• /
• pp.70-77
• /
• 2007

Twelve chlorophenols (CPs) were extracted by liquid phase microextraction (LPME) from the industrial waste-water and analyzed by GC/MS. To establish the optimal conditions, species of extraction solvent, sample amount, pH of sample, salting out effect, a number of sampling and plunger movement speed were investigated. As a result, the linearities of calibaration curves ranged from 0.9913 to 0.9999, while LODs and LOQs were from 0.05 to 10.0 ng/mL except 2,3,4,5-tetrachlorophenol and pentachlorophenol. Using this method, 4-chloro-3-methylphenol confirmed from waste water at the concentration of 784 ng/mL. The method can be applicable to detect chlorophenols from industrial waste-water.